When I connect the DI output of my new Origin 20c to my recording system (ART USB Dual Pre into Logic Pro on M1 iMac) there is a constant hum. A noise gate set to -30dB just cuts it out. The combo speaker itself is silent. I cannot find any help on the Marshall website!
I seem to be having the same issues that a lot of people have reported, where I cannot get the Marshall Gateway app to connect to my Code 25. I've only had the amp for about a week and I cannot get the app to see it. ?
I can connect to the amp via Bluetooth using my phone (Pixel 3a, Android 11) and whilst connected, can use it as a BT speaker to play music from Spotify. However, nothing I do seems to get the app to connect to the amplifier.
-I've updated the amp to the latest firmware using my laptop/web browser.
-I've followed all the instructions in the Bluetooth Connectivity Troubleshooter to the letter (CODE - Gateway Bluetooth Connection Troubleshooting - my.marshall.com)
No matter what I do, or what order I install/uninstall/connect, the app will not see the amplifier. Everything works otherwise - I'm able to apply Patches from ? using a USB connection - and the amp sounds great. I'd just like to be able to control it from my phone.
Hi - never having used a DI out before, being reasonably new to home recording and not wanting blow up a newly purchased SC20H, the question is - can I just run an instrument cable (or speaker cable ?) from the DI Out on the back of my SC20H straight into the Mic/Instrument inputs of my audio interface (Presonus Aidiobox USB) ? I dont have a cab for the head yet and want to start using it this way until I get a cab. Thanks in advance.
Quick 4 part question: A) can I use the USB to get a line level signal into my PC that my digital interface will push to my powered monitors?
B) when using USB is the cabinet speaker muted?
C) must my DAW be open to make this work?
D) in this USB mode, can the CODE 100 be operated without speakers connected?
I'm having a problem when I recording my guitar.
My recording guitar setup is:
Gibson Les Paul Studio -> Bugera 333xl Infinium Head Amp (with instrument cable)
Bugera 333xl Infinium loudpeaker output -> Active DI Box Behringer Ultra-G (with speaker cable)
Active DI Box Behringer Ultra-G Direct Link -> Marshall 4x12 MX412B (with speaker cable)
Active DI Box Behringer Ultra-G Output -> Presonus Studio Live AR16 USB Mixer (XLR cable)
I'm using Logic Pro X Software.
I record a guitar riff in Logic Pro x as audio track (audio_1) and then i want to record a second guitar like a fill guitar or lead guitar (audio_2).
To record audio2 i turn on audio1 to listen the guitar riff.
When i’m gonna listen the audio2 in solo mode besides the lead guitar I can listen the sound of my audio1 with very low volume but i can listen it to
Can you help me with this problem please ?
How can I update firmware when I don't have USB port on my Marshall speaker
I'm using USB on my Mac and the Mac sees the Code and allows me to set the speaker to it.
When I pull up a Youtube video and start it the video will play for about 5 seconds and then halts.
It's almost like something else is intercepting it. It basically locks up and I have to close the browser.
Same issue when using the Code 25 as input device on Mac for Garage Band. It recognizes it but when I record
upon playback the sounds are scratchy and unusable
This Code 25 works on my Windows Machine both ways as Input and Output device flawlessly
I have installed the latest firmware so that is not the issue.
Any ideas on what it might be causing the problem on the Mac?
Actually I'm totaly not interested in bluetooth connection, but of course I understand that it might be an essential prolem for some people...
But there are some other problems I'd like you to find good solution for.
1. Master volume. From 0 to 10% there is almost no sound, over 10% it becomes very loud.
2. Decreasing sound level with Volume pot results in decreasing USB signal level - not acceptable for players using USB output for recording in DAW software. It would be nice if for clean preamp gain at 2 and volume at 3 give recording level about -6 dB, now it is about -36 dB...
Best regards, Jacek.
P.S. What is a frequency range of CODE 25 speaker?
If I want to plug my 100h into my PC via USB, does it still need a speaker load or can I use it without a cab connected?
CAN I ADD ANOTHER SPEAKER CABINET TO THE CODE 50
I WOULD LIKE BOTH CABINETS TO PRODUCE SOUND
MAYBE THROUGH THE USB OR A PORT OUT OR A WIFI CONNECTION
The Code 25 makes a strange sound when letting a plucked guitar string sound die out, only when "amp" is selected (might be digital artifacting?) I saw one question about this via USB, but what I hear is not via USB, just out of the amps own speaker, no USB connected!
I wrote in a question you can please excuse me as now that I have the amp in hand, I am very happy. This is excellent.
I would consider how to add a high frequency speaker so music streaming is a bit brighter, but I notice the sound via USB is pretty good and one up on the Mustang series which did not stream music out the USB port. Thank You. I kept my G-Dec 3 Thirty around for that reason (plus tweeter and line outs - I might add). As I get used to this I might find the headphone out sufficient but wish you had added Lineout so the speaker stayed engaged but could take the lineout to other amps or recordering devices.
Can you tell us which interal speaker is used, ohm rating and the frequency response?
I do not want to open it up to figure it out since I plan on maintaing my warranty, at least for the next year.. :)
PS who signed off on this design, give them a raise :). But if you had a version with the features I mentioned, I would gladly have paid the additional cost and only been fully satisfied. Like I am at 96.75% now. You can quote me.