Questions
Showing results 1 to 17 of 17
0

votes

1

answer

461

views

I noticed there is an emulated out on the back of the 20Watt Dsl head. From reading the .pdf manual, I understand that the head needs to stay connected to the speaker cabinet. So I know to never un-hook it, however - My questions being - 

Do I need to be in Stand-By mode to actually use the headphones? If not, will the sound still come from the speaker cab? 

Also, can I just plug my headphones directly into the Emulated Out? the .pdf manual says the Dsl20 Emulated Out supports Headphones. But I've seen people comment in other places that you need a headphone amp that increases volume or something. I haven't been able to test with headphones yet, and I kinda' wanna' get the right answer on this before I try. Thanks. 

 

Loving the Amp and Speaker cab though haha. Just came in yestreday. 

asked 29 May 2021 at 06:33 AM

Nicholas Thomas (1)
2

votes

4

answers

954

views

Hi,

How do you control system sound (power on & shut down) volume on Emberton?

The system sound is VERY loud, and aggressive sound. 

It's silly when you hear relaxing yoga music, and then you're forced to hear very loud guitar sound at the end of the meditation session.

Thanks.

edited 29 Mar 2021 at 12:19 PM

John Doe (2)

asked 29 Mar 2021 at 12:18 PM

John Doe (2)
0

votes

1

answer

261

views

I have 2 cabs,   2x12(16 Ohms 100w) and 4x12(8 Ohms 240w).

In Code 100h manual, says the speaker output is MINIMUM 8ohms load. I can use my 16 ohms cab without harm the amp head or the cab itself?

I'm getting trouble in the 4x12 transportation, the 2x12 is way lighter. Until now I'm only using the 8Ohms cab in the code 100h.

asked 22 Mar 2021 at 02:04 PM

Gabriel Salvi
0

votes

0

answers

346

views

Hello,

I am having trouble confirming if a speaker must be connected in order to use the D.I out on my Marshall 2525h. The manual only contains one sentence of information which doesn't provide enough clarification considering this can destroy an amplifier if misunderstood.

Would I have to connect my 2525h  to a 1x12 cab (via 1x8 ohm connection) in order to use the D.I output? This signal from DI would be sent to a Two-notes C.A.B.M for Impulse response, before going straight into the audio interface?

asked 02 Jan 2021 at 06:19 AM

Mitchell Morabito
6

votes

9

answers

6.6k

views

This is killing me! total dealbreaker. If I can't find a solution I'll return this speaker which I love everything else about it.

It goes to auto-standby if it's unused for 20 mins regardless of bluetooth use or sound coming from RCA jack. But whenever I play something next time, I have to touch the knobs to wake it up manually. I put the speaker in my bookshelf which my plan is to not need to touch it in every use.

I want it to not go stanby mode ever. Is it possible? I couldn't find any answer in the manual, in the forum or in any other place. Sent a support inquiry as well, but I'm curious if anyone else is having same issue.

asked 08 Feb 2020 at 05:38 PM

Mehmet Yildiz (9)
0

votes

1

answer

706

views

Manual says "Connect a single speaker cabinet here for the DSL1HR head". Is it means I can't use cabinet with two 8ohm speakers in series?

asked 04 Jan 2020 at 09:50 PM

Dmitriy Sokolov
1

vote

2

answers

950

views

The manual that came with the head says use output 3 when using a single 8 ohm cab. 

The online manual on the Marshall website says to  use output 2 when using a single 8 ohm cab.

I  have plugged a single cab into these both  at different times and output 2 seems to have more volume and treble than output 3

I am slightly confused and annoyed as shouldn’t  either 8 ohm output sound the same irregardless of which one I plug my single 8 ohm cab into?

I would appreciate some clarification so that I can use the correct 8 ohm output for my speaker cab!

Update to my original post as I  have an additional question related to rear speaker outputs.

The third output speaker socket and the revised manual show this as output for 2x16 ohm. (Mine has the modified sticker attached)

Does this mean:

a: that you can plug two 16 ohms speaker cabs which have been set up in parallel into output socket 3 and the power amp sees a total of 8 ohms? .

b: output socket 3 already internally wired in parallel with socket 2 and such you plug one 16 ohm cab into socket 3 and one 16 ohm cab into socket 2, for a total of 8 ohm impedance?

c: Not sure what else could be possible?

Could you please confirm which is the correct approach? Thanks, Ross

edited 01 Jun 2020 at 03:44 AM

Ross Ferro (1)

asked 13 Nov 2019 at 11:11 AM

Ross Ferro (1)
0

votes

1

answer

596

views

The 100w head is not loud enough for me so can i run it into the return of a louder head , this would mean the louder head having the 4x12 connected + the code head would have no speaker connected , now i always thought that solid state amps do not require a load box but the manual says do not leave the speaker un connected , so can i run this way or do i need a load box even tho the amp is solid state ?

asked 28 Sep 2019 at 02:09 PM

STIXX DIAMOND
0

votes

1

answer

689

views

Hallo,

I just purchased my new Origin head 20H and I noted a discrepancy between the rear panel speaker TAGS and the electronic manual and photo available on Marshall website. In my amp there is the socket n.2 for a mono 8 ohm connection ans the socket n.3 is labeled with a dotted line to the n.2 for the connection of a pair of cabinet 16 ohm. while in the Marshall web site the sockets n.2 and n.3 are labeled with 8 ohm. Could you Clarify please? thanks.

edited 26 Aug 2019 at 10:12 AM

Roberto ACErob71

asked 26 Aug 2019 at 10:11 AM

Roberto ACErob71
0

votes

2

answers

887

views

Hi, 3 question:

1) I'm Italian and I just purchased on ebay a brend new DSL40Cr from a UK shop. I was wondering if the ampli still works at 220V - 50 Hz as per manual, regardeless the fact it comes from UK, and if will arrive with power calbe schuko plug or UK plug. In this case may I use an adaptor male shuko/female UK ?

2) I would like to know if I can use an external speaker as additional together with the internal Speaker, for example the internal 16 Ohm speaker + an external 8 Ohm speacker connected obviously at right socket.

3) in case of use of one external speaker (e.g. 8 Ohm ) which one I should connect of the two socket where is labeled down "1 x 8 OHM - 2 x 16 OHM" ? is it indifferent, the one to the left or the right ?

update for the question n.2: maybe I figure out how it has to be done: unplug the internal speacker from 16 OHM socket and plug it into the 8 OHM speacker. plug a 16 OHM external cabinet into the other 8 OHM Speacker socket. otherwise only configuration showed on manual are allowed. Is that correct?

 

thank you

edited 15 Jan 2019 at 01:35 PM

Roberto ACErob71

asked 15 Jan 2019 at 01:06 PM

Roberto ACErob71
0

votes

0

answers

489

views

Hi people.

Firstly, I would like to say what a great site.

Secondly, forgive me if this has been asked elsewhere.

Ok, the question is:

I have a Marshall origi n 50 head(beautiful bit of kit!!!!)

And a marshall 1936 cab.

The issue i have is which speaker connections to use.

The manual forvthe amp says socket 3 at 8 ohms, yet the back of yet amp shows socket 2 as 8 ohms!!!

Also even though amp is not stereo can i use 2 speakef cables ftom the 16ohm sockets????

A bit crazy i know but dont wznt to blow me new amp for the sake of asking the great znd wise

Many thanks in anticipation

asked 14 Jan 2019 at 11:32 PM

PATRICK BENNETT
0

votes

1

answer

895

views

Ive read the manual for the jvm410h but dont fully get the outputs.

All i need to know if anyone can help it what out puts do i use on amp and cabs when i plug into my 1 1960a and when i use my 1960b too so half stack full stack.

I need idiots guide.

Thanks 

asked 06 Oct 2018 at 07:18 AM

Paul Evans
0

votes

1

answer

4.3k

views

Hallo,

I got a doubt on well interpretating the manual where it states:

WARNING: When using the DSL1HR head
for ‘silent’ practice or DI recording ALWAYS
disconnect the speaker cabinet from the
amplifier’s rear panel before switching on.
NEVER unplug the speaker cable from the
speaker cabinet while it is still connected
to the amplifier rear panel. This may stress
the amplifier’s power-stage and in extreme
cases may lead to valve and/or transformer
failure.

can someone confirm what I understand: if I want to play using an headphone for silent practice (connecting my headphone to emulated line Out), I shall prior disconnect the external speaker from the rear of the amplifier (shouted off), (and never from the rear of the speaker cabinet). So I can Play the amplifier using headphone without connection to the cabinet? is that correct? An this is applicable also if I connect the amplifier to a mixer (by using Line out). That is quite strange because all other amplifiers recommend to never disconnect the speakers, with or without an headphone or something helse. Please help! I don't want do damage my DSL1HR. Thanks. Cheers.

 

asked 06 Sep 2018 at 11:32 AM

Roberto ACErob71
0

votes

1

answer

769

views

I have an Axe Trak insulated speaker (here is a link to info on the speaker) www.axetrak.com/guitarmanual.pdf

When I have run it from the Marshall it has cut out after playing for a while, I have turned off the amp and then the following day used the amp with its built in 12" speaker and it has been fine. When i read the JTM 60 manual it said it is fine to drive a 8ohm from the external speaker output ONLY, not the internal out connection.

Is this OK? when things cut out it makes me worry about my Marshall and I really don't want to cause it any damage.... Also I have checked the speaker lead and that is all good, when it cut out it the sound broke up and faded in about 1 second. It is the 2nd time is has happened so i thought I best get some advice. The Axe Trak is great and means i can play a valve amp and get valve amp tone and not disturb my neighbours, it is a great bit of kit for home recording and I want/need to be able to use it. Any advice?

Thanks, Robin..

edited 16 Jun 2018 at 12:48 AM

Robin Brown

asked 16 Jun 2018 at 12:36 AM

Robin Brown
0

votes

1

answer

1.6k

views

Hi,

I want to change the speaker of my Marshall DSL 40C, but the new speaker is of 8 ohms. In this case I will use just one 8 ohms output?  The 16 ohms output and the other 8 ohms output will be unplugged? 

And about the power (RMS) of the new speaker? The manual of the DSL 40C said that the power is 40w, but the original speaker celestion seventy 80 have 80w... The new speaker can have 80w, 100w, 120w?

asked 03 Jan 2018 at 09:38 AM

Vinicius Andrade
1

vote

2

answers

1.7k

views

Hello

In the manual is told not to use the Code 100 head without a speaker? Why?

I think it's not a valve amp.

 

Martin

asked 14 Dec 2017 at 10:41 AM

Martin Louis (1)
0

votes

1

answer

993

views

Hi there. Just bought a code 50, and I'm really enjoying it. A request! any chance of getting A dot icon on the speaker selection part of the app to show wether you are selecting a 4, 2 or one speaker cab, rather than havig to go to the manual to check.

Cheers. Jim.

asked 18 Nov 2016 at 03:37 PM

James Dunne
Showing results 1 to 17 of 17
Loading - please wait...