Questions
Showing results 1 to 5 of 5
0

votes

1

answer

35

views

I have a two part question 🤔.  I have my two amplifiers listed above.  I have both electric and electric acoustic guitars.  I'm learning how to play and bought the 50 watt acoustic Amp as I  really like the sound of over wound humbuckers through it for heavy slow blues.

First question,  keeping the AS50D as the main sound, can I connect it through/to the 100 watt Marshall? Both are 4 ohms and I would like the maximum amount of power to drive my 4 x 12" cabinet of 8 ohm Jensen Tornadoes that are wired in series for the 4 ohm 100 watt MG HDFX. Then I would have 150 watts total to drive my 400 watt total limit.

 

Question two,  can I connect my 50 watt AS50D Amp to my 4 x 12" speaker cabinet by running a cable from the back of my Amp to the cabinet. I have footswitch,  line out and (effects loops) send and return Jack's to use.

  Even though my 4 x 12" cabinet would be very under powered. I would like to hear the sound of the AS50D  through those speakers. I'm new to guitar and don't want to ruin any of my equipment.  I did also have a guitar made through two luthiers,  I also made the 4 x 12" cabinet to match my guitar.  I call them Snort and the box.

  I have the components for the sound I'm looking for,  now I need to combine them all together.  I truly appreciate guidance from the technical support team at Marshall. 

God bless you for your time and kindness.  Thank you,  Eric Dailey 

asked 06 May 2022 at 09:49 PM

Eric Dailey
0

votes

1

answer

323

views

Hello,    New amp I procured and I am hoping to get some Q's answered regarding. 

It did not come with a footswitch and being new to all of this I do not know why I need one or which footswitch to get ????

Also, I was told by the original owner that it is quite than it used to be and may need a new tube.   Also do not know which way to go with this ...   

 

Last point is when switching over from clean to overdrive it is buzzing and I am not sure why...

 

After hours on youtube and reading the instruction manual I am even more confused. 

 

Thanks in advance for comments/advice. 

 

Wade

asked 25 Aug 2021 at 11:03 PM

Wade Gail
0

votes

0

answers

585

views

I was wondering if the creator of the KASHMIR preset would be interested in also creating the FLANGER part for KASHMIR using all the current preset settings (amp, cabinet, speaker etc) as a complimentary preset for the turnaround section of the song.  I believe, from forums, that a preset will switch better (Marshall CODE footswitch) if the preset has the same amp, speaker and or cabinet setting as it takes away the millisecond delay of switching between amps in a particular preset.  Look forward to your answer and or creation of said beasty.

Regards Kev

 

asked 30 Jul 2019 at 02:07 AM

Kev Lawlor
0

votes

1

answer

1.1k

views

Hello.  I have a Marshall Code 100 Head, 4 12 cabinet and the 2 12 combo amp.  Absulutely love these amps.  I also have the 3 way footswitch.  What I can't figure out, is how to be able to turn off and on the REVERB from the foot pedal.  Is there a way for this?  It defaults to allow you to access the Distortion, Modulation and Delay but what about the reverb?  Any ideas?

Thanks, Larry

asked 21 Jun 2019 at 05:33 PM

Larry Tucker
0

votes

2

answers

1.5k

views

I'm looking for a Marshall Cabinet for my newly aquired 3203 - It origianlly paired with a 4x10 but am wondering how it will sound with a 2X12 and also - will just any footswitch do? I think the answer on that last one is yes but I am not sure.

asked 10 Jun 2016 at 06:11 PM

Jhon Baker
Showing results 1 to 5 of 5
Loading - please wait...