Questions
Showing results 1 to 8 of 8
0

votes

1

answer

323

views

Hello,    New amp I procured and I am hoping to get some Q's answered regarding. 

It did not come with a footswitch and being new to all of this I do not know why I need one or which footswitch to get ????

Also, I was told by the original owner that it is quite than it used to be and may need a new tube.   Also do not know which way to go with this ...   

 

Last point is when switching over from clean to overdrive it is buzzing and I am not sure why...

 

After hours on youtube and reading the instruction manual I am even more confused. 

 

Thanks in advance for comments/advice. 

 

Wade

asked 25 Aug 2021 at 11:03 PM

Wade Gail
0

votes

1

answer

806

views

I noticed there is an emulated out on the back of the 20Watt Dsl head. From reading the .pdf manual, I understand that the head needs to stay connected to the speaker cabinet. So I know to never un-hook it, however - My questions being - 

Do I need to be in Stand-By mode to actually use the headphones? If not, will the sound still come from the speaker cab? 

Also, can I just plug my headphones directly into the Emulated Out? the .pdf manual says the Dsl20 Emulated Out supports Headphones. But I've seen people comment in other places that you need a headphone amp that increases volume or something. I haven't been able to test with headphones yet, and I kinda' wanna' get the right answer on this before I try. Thanks. 

 

Loving the Amp and Speaker cab though haha. Just came in yestreday. 

asked 29 May 2021 at 06:33 AM

Nicholas Thomas (1)
0

votes

1

answer

761

views

Manual says "Connect a single speaker cabinet here for the DSL1HR head". Is it means I can't use cabinet with two 8ohm speakers in series?

asked 04 Jan 2020 at 09:50 PM

Dmitriy Sokolov
0

votes

2

answers

972

views

Hi, can anyone explains to me WHY we can't use a CODE 100H without the cabinet? For VALVE amps there is a good reason for which you need the cabinet always connected but for solid state amps it seems very strange.

Is it maybe an error in the manual? Maybe it's a phrase that has been written for all the Marshall valve heads and it was mistakenly added to the CODE as well?

Please let me know, I have an application where I only need the 100H coming up soon.

Thanks!

asked 23 Dec 2019 at 11:53 PM

Lele X (14)
0

votes

1

answer

743

views

Hallo,

I just purchased my new Origin head 20H and I noted a discrepancy between the rear panel speaker TAGS and the electronic manual and photo available on Marshall website. In my amp there is the socket n.2 for a mono 8 ohm connection ans the socket n.3 is labeled with a dotted line to the n.2 for the connection of a pair of cabinet 16 ohm. while in the Marshall web site the sockets n.2 and n.3 are labeled with 8 ohm. Could you Clarify please? thanks.

edited 26 Aug 2019 at 10:12 AM

Roberto ACErob71

asked 26 Aug 2019 at 10:11 AM

Roberto ACErob71
0

votes

1

answer

4.6k

views

Hallo,

I got a doubt on well interpretating the manual where it states:

WARNING: When using the DSL1HR head
for ‘silent’ practice or DI recording ALWAYS
disconnect the speaker cabinet from the
amplifier’s rear panel before switching on.
NEVER unplug the speaker cable from the
speaker cabinet while it is still connected
to the amplifier rear panel. This may stress
the amplifier’s power-stage and in extreme
cases may lead to valve and/or transformer
failure.

can someone confirm what I understand: if I want to play using an headphone for silent practice (connecting my headphone to emulated line Out), I shall prior disconnect the external speaker from the rear of the amplifier (shouted off), (and never from the rear of the speaker cabinet). So I can Play the amplifier using headphone without connection to the cabinet? is that correct? An this is applicable also if I connect the amplifier to a mixer (by using Line out). That is quite strange because all other amplifiers recommend to never disconnect the speakers, with or without an headphone or something helse. Please help! I don't want do damage my DSL1HR. Thanks. Cheers.

 

asked 06 Sep 2018 at 11:32 AM

Roberto ACErob71
0

votes

1

answer

1.5k

views

Hi!

I have a Marshall 1936 2x12 cabinet, but I am unsure how to correctly use the input jacks (8 ohm/16ohm).

Could you please send/post a PDF of the user manual?

Thank you so much!

 

asked 27 May 2017 at 12:29 PM

Greg A
0

votes

1

answer

1.3k

views

Hello,

I was wondering if you could recommend any extension Marshall cabinet for my Class 5 combo amp.

As per the link , https://marshallamps.com/support/faq/impedance/ ... where can I find that information on your website?

 

WHAT EXTENSION CABINET WILL WORK WITH MY COMBO AND WHICH IMPENDENCE DO I SET MY AMPLIFIER ON?

 

Most of our combos have an extension cabinet designed to match its size and sound. Our website has full details of which combos and extension cabinets work together and the user manuals, available to download from the support section, give full explanations on how to connect them. We recommend going to your local Marshall Dealer so you can test out the combos and cabinets to see which one suits you the best.

 

Regards,

 

Antoine

asked 25 Aug 2016 at 08:36 PM

Antoine Mai
Showing results 1 to 8 of 8
Loading - please wait...