Questions
Showing results 1 to 20 of 44
0

votes

2

answers

19

views

I recently purchased a CODE25 to use as a practice amp. It looked like something fun I could play around with.

The first few days it was ok as I was only using some of the factory presets. Trouble started as soon as I edited one or saved an online preset. The sound dissappeared (speaker) and the display got very faint. Restarting the amp made the display ok again but still no speaker sound. I reset the presets (hold down Amp while turning it on) and that seemed to do the trick.

But soon after the sound issue started again. I reset the amp presets, re-installed the firmware, but I only had sound for 2-3 seconds after boot, then nothing.

I have now discovered that if I plug in a headphone (which has sound) and then unplug it, I have speaker sound again. This makes me even more confused. I haven't tested long enough to confirm that this will work over time. 

I see that there is a lot of posts regarding sound issues and requests for a long overdue firmware. But have anyone found out any new tricks to overcome the issues?

I sent an email to Servicedesk last week but haven't recieved a response of any kind.

asked 14 Apr 2021 at 11:00 AM

Bjørn Gamlem
0

votes

0

answers

167

views

Hi, I'd want to know if disconnecting the speaker on a 20w Origin head would activate the standby (so this won't damage the amp) even if then I go through the send to an audio interface and not returning to the amp through the return or anything else (and so NOT using the di out). In fact I would like to use my favorite cab+microphone+power amp simulator and then connect it to the interface and listen with my headphones on and I think it would be impossibile and harmful to the sound to add another cabinet simulation to the already-present One in the di out (right?) and so I would exit from the send.

2 another simple questions:

could i do this with a combo, too? In that case, how do I disconnect the speaker?

The last one: if I exit from the send, I'll take the preamp signal, right? And if I exit from the di out will I have the preamp signal (with the cab simulation) or will it just be the guitar signal with the cab simulation only (I assume I won't anyway have the power amp too)?

Sorry for my bad english and for the ignorancešŸ˜…

 

edited 11 Jan 2021 at 10:45 AM

Jacopo Gaggia

asked 11 Jan 2021 at 10:17 AM

Jacopo Gaggia
0

votes

1

answer

261

views

After struggling for an hour with instructions in the User Manual and online Support, here's how I was able to pair my Monitor Bluetooth Headphones with a second source:

1) Turn off Bluetooth on the existing/first source.
2) Power off Monitor headphones.
3) Press and hold the Power button for ~10 seconds (in other words, keep holding after the initial "power on" tone) until you hear a second tone.  The LED on the headphone will blink with a sapphire color.
4) Discover the Monitor headphones on the second source and connect.

I love my headphones, but the User Manual and on-line help are deficient on this topic.

asked 10 Dec 2020 at 10:55 AM

Nelson Kersey
0

votes

2

answers

251

views

Hi everyone,

                            I've a very similar question to one that has already been asked. 

Is it safe to use the headphone/line out without any speakers connected to the rear on a MG100HDFX head?

Also, when I do use the speakers, do I have to use both speaker outputs at the rear or is using  just one ok?

One more thing, is it safe to use my faulty G80R CD as a speaker cab with my MG1000HDFX, I'll be using nothing like full power, just having fun in my room?

Thank you in advance,

                                                 Voxathon.

asked 18 Nov 2020 at 12:55 PM

Vox Athon
1

vote

0

answers

177

views

The sound that a headphone, connected with the code100, produces does not include the effects that are placed in sent and return. That is really strange. 

Music played with a phone or tablet that is connected with Bluetooth does go through the effects in the sent and return loop. Really strange again in my opinion.

I would like to know  why it is wired this way and I would be really happy with a solution for at least the headphones!

Kind regards!

asked 03 Nov 2020 at 08:47 PM

Ed de Bakker (1)
0

votes

1

answer

113

views

Is it possible to use headphones with the Stockwell 2? They don't work plugging into the 3.5mm AUX port, but would it work to buy a USB-C to 3.5mm jack converter?

asked 29 Oct 2020 at 09:58 AM

Gareth Chiles
0

votes

1

answer

488

views

When I plug my headphones into the headphone jack, the amp still plays out of the speaker. Is this supposed to happen? How can I disable this?

asked 01 Jul 2020 at 09:33 AM

Nathaniel Chamron (10)
0

votes

1

answer

346

views

Hello everyone,

I recently bought a Marshall CODE25 and I want to connect headphones, but I don't know exactly what impedance the headphones should have because in the amp's tutorial it does not specify what output the headphone connection has.

Thanks greetings.

asked 07 Jun 2020 at 10:33 PM

David Hidalgo Luna
0

votes

1

answer

461

views

Can I use bluetooth headphones with ampli Code 50 to play guitar and listening it? I have bluetooth headphones but don't works...

asked 02 May 2020 at 10:10 AM

Marco Brini
0

votes

1

answer

529

views

Hi. Just verifying. Can I use The Behringer HA400 power headphone amplifier through the DI with the origin head without the cab attached or only into a mixing desk before removing the speaker ?
I’m just looking for best way to use headphones without the speaker attached .

thanks. 

P.s the origin amp is awesome. Love it. 

asked 19 Apr 2020 at 12:41 PM

Johnathan McLam (1)
0

votes

2

answers

634

views

Hello.

I've been using the Marhsall Monitor bluetooth headphones for about a year and I haven't had any issues using these in rain or during really sweaty sessions at the gym. I'm now looking to upgrade to the Marshall Monitor A.N.C. II. And from the promotion video posted by marshall(https://www.youtube.com/watch?v=xMy3OXCXZvk) I see at the 1:17 mark that(what I assume is) the microphones for A.N.C. will be located on the top of the headset.
Will this pose a higher risk for water damage on this headset modell?

See screenshot from promotion video:

Thanks for any type of response.

B.R.

Kristoffer Hellstrand

edited 11 Mar 2020 at 08:06 AM

Kristoffer Hellstrand

asked 11 Mar 2020 at 08:05 AM

Kristoffer Hellstrand
0

votes

1

answer

1k

views

Hi Guys,

got an origin 20 combo, trying to use headphones on di out. What am I doing wrong? Got speaker working but no sound in headphones.

I take it first thing is unplug speaker??? Then what, do I need to change the power setting or something?

hanging off till I hear more.

ali

 

 

asked 19 Feb 2020 at 05:51 PM

Alistair James
0

votes

1

answer

572

views

Looking to confirm, when using headphones on 5 Watt, you disconnect the speaker correct?  Also, does this need to be in low power only or can it be in normal power for headphone use?

 

asked 29 Oct 2019 at 12:40 AM

tom zenner
0

votes

1

answer

916

views

hallo Marshall team,

please can you tell me if the DI/Out socket can be used also with headphones?

is it confirmed that once I connected the DI/Out to a mixer PA or a Audio Interface, I can un-plug the speaker cable fro the amp without damages?

thank you

regards

asked 27 Aug 2019 at 12:48 PM

Roberto ACErob71
0

votes

6

answers

712

views

I get no guitar through the headphones.  What must I do to get the audio from my guitar to the headphones?  I would like to use this as a line signal to another amp.

I do get audio out from my phone to the headphones when Bluetooth is connected. When Bluetooth is connected, whatever is playing on the phone will be heard through the headphones. So, I know the headphones AND the headphone jack both work. 

asked 08 Jul 2019 at 03:06 AM

Antonio Hillario
0

votes

1

answer

1k

views

Hi there,

I hope my english will be understandable. :)

I bought the Marshall Major II Bluetooth headphones almost two years ago and they were doing well and I was happy with them. Now there's a problem with the controll knob on the backside. So I mailed the support service and got excellent help from them. I mailed some photos and conformation that I really have bought them. Now they want me to totally destroy them by cutting cables and snapping them in half before they can send new ones. I find this quite an unusual procedure and want to know if this is normal and if anyone had made similar expierienced and if this is trustworthy. 

Thanks for your help

Greetings from Germany

 

asked 23 May 2019 at 05:19 PM

Miles Müller
0

votes

2

answers

696

views

The headphone output on my Code 100 head is extremely quiet, requiring me to crank the volume on the amp to hear the signal at all in the phones. The phones are new and work fine in every other application I've used. Could I be missing something?

asked 19 May 2019 at 10:19 PM

Matthew Miller
0

votes

1

answer

1.5k

views

Hey!

I'm currently looking at getting either the Marshall DSL1H or DSL20H amp head. I know that they both have emulated out's that can be used with headphones, but what I'd like clarified for me is how this would work exactly. I'm not going to be buying a cab for it right away, but would like to be able to still use all the knobs on the amp to sculpt te tones I want and to also control volume levels. Is this something that I can achieve without a cab connected to it? If I need a cab connected to it can I just connect it to a load box? 

Thanks.

asked 26 Apr 2019 at 02:25 PM

Myke Helstein
0

votes

1

answer

529

views

Hi, I bought Major II on Amazon and some users complained that the ones that come in are often not original. So I would like to ask you, if on the basis of these photos we can deduce the originality of the product (with a code on the label). Thank you ;)

 

https://twitter.com/LocoToretto/status/1114819190567985152

asked 07 Apr 2019 at 09:16 AM

Raffaele Sanseverino
0

votes

1

answer

496

views

Hi, dear marshall.

Last  year i have bougth headphones Mrashall MiD. But they have got broken. I don't have service center in my city, and the store, i bought it closed. But headphones still have a 1 rear free repair warranty.

Please answer, how can i repair it?

 

With respect, Andrey N.

asked 17 Mar 2019 at 03:52 PM

Andrey Nerpin
Showing results 1 to 20 of 44
Loading - please wait...