I am not able to transfer presets from Mac to Code 50. The display below preset shows code not available though usb is connected
I have a CODE 100h + CODE412 and I love them !!!!
I use a pedal board with different effects and was thinking of adding a looper / switcher (Boss ES-5 or MUSICOM LAB EFX LE).
I would like to know if with the looper I have listed I can change presets to CODE100H via midi. Do I need a USB / MIDI interface? Thanks
Hi! I have an issue while trying to transfer dowloaded presets to my Code25. It occures both usb and bluetooth connections. On a usb connection i click the “amp” icon on a preset, it’s name appears on a Code screen. I push and hold store button on amp, “saved” appears. But then Code becomes freeezed, it does not react on button push etc. when i switch it off and then switch on it works fine, preset available on amp. The same issue appears when i try to transfer presets using Gateway app. What I do wrong?
if i use a clean preset of the marshall code 100H i got issues with crackling sounds. Even after turning it off and on. Its extremly annoying and it destroyes all that i record into my DAW. With this crackling sounds this Device is absolutly useless!! I've also updated to the latest Firmware version but nothing changed!
I know I can override any CODE amp preset with CODE USB connections from the website or by changing on my phone while connected and saving either on the phone and/ or amp. But How do direct amp changes work with Gateway while disconnected and then synced later on?
In other words, if I save modifications on my amp to a particular preset and I am not connected to my gateway on my phone, when I do connect and sync later, which setting wins? Does the phone setting override the amp-stored setting (ie. back out the mods made on the amp / push the settings to the amp from the phone) or does the phone pick up the modified amp setting from the amp and store it in Gateway (ie, pull the settings from the amp and store in my phone)?
Also, I have the first 30 presets set up for ones I use to perform and are addressable using code programmable foot controller. If I want to archive/backup those presets someplace to guard against an unplanned need to do a factory reset, does it make sense to store them perhaps in the cooresponding setting in my Library ( the blue section of My Gateway ) That way i can bring them into the amps and store them one at a time from the library back into the presets on the amp, or is there a better way to backup/restore presets in the event of a factory reset?
I purchased a Marshall CODE 100H + 212 Cab recently.
I downloaded the Marshall Gateway app and have created a My Marshall account.
The Amp came pre-loadedwith a 100 presets.
The Marshall Gateway app also came pre-loaded with 100 presets,
but the Gateway app presets are different from the ones in the amp.
I synced the 100 presets in the Gateway app to my "My Marshall" account Library.
I have edited and saved some of the Presets on my Amp.
I want to transfer the edited Presets on my Amp to my "My Marshall" account Library, and then put them in my Gateway app,
How do I Transfer a Preset FROM my CODE Amp to my "My Marshall" account Library?
I see the option to transfer a Preset from My Library to the Amp,
and I understand how to manage / organize the Gateway app presets from the Library,
but I don't see a way to put a Preset on the Amp in the Library.
Do I have to manually re-create it in the Library?
The My Gateway online interface is great for managing / organizing the Gateway app presets from the Library.
It would be useful if there was as similar interface for managing / organizing the presets on the Amp, when connected via USB.
Hello, I have acquired the CODE 25, really an excellent amplifier, very versatile and very good presets. My problem and please I hope you help me to resorve it, is that even though I can connect via Bluetooth, I can listen to my tracks ....... the big problem is that when I want to use the FX or presets it appears that there is no amplifier connected ... (either from my android phone or my Ipad I ... I do not understand what the problem is.) Secondly, when I want to install the MARSHALL FIRMWARE UPDATE UTILITY, to enter presets or update the ampli, does not recognize the connection.I request guidance to be able to make full use of such a beautiful tool for my music.I use Widows 10 and G. Chrome.For your attention, thank you very much
I connected my Code 50 to my laptop via bluetooth, but the my.marshall presets says "CODE not connected". I tried connecting via USB, but the amp has a goofy connector that standard USB cables do not connect to. Also - I can connect via the Gateway app on my phone, but the presets I add to My Library do not show up (even though it says that they have synced).
Hello, I would like to connect one of my PCs (OS linux) on a Marshall CODE 50 and take control via usb midi.
When I open /etc/dmmidi2 in read acces. Reading file char by char, I see information when I touch the buttons of the amp (PREFX, AMP, MOD, ...). I can find the information in CODE-Midi-Implementation-Chart-V2.1.pdf.
I usually get two or three bytes and cross it with the document.
But this frame is not in the form Start of Transmission> Header> Command> End of Transmission.
By against when I open /etc/dmmmidi2 in write access, I can not send any command.
After having turned on the amp, I sent the following sequence for RECALL PRESETS 05:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x73 0x01 0x05 0xF7
or RECALL CURRENT SETTINGS:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x72 0x01 0x00 0xF7
Start of Transmission> Header> Command> End of Transmission
This command does not seem to work. Is there an intermediary step?
Would it be possible to give me a typical sequence to the CODE or a document that will explain the procedure to operate (ON / OFF) one of the button (PREFX, AMP, MOD, ...) of the amp.
Thank you in advance.
can any one help me i can't down load any of my favorite guitar players presets,do i do it manually on my phone or what i got how the USB gets the music from my library,but every time i pair my phone with my marshall it stays on for one preset i can't even reconize so i play all my music songs pink floyd led zepplin SRV JIMI H On simple clean setting what the ,and futher more at a guitarist presets he might have used at the left bottom corner there is 4 or 5 boxes,phone box amp box and stupid finger sign and so on but i get a stop sign code when i click on the little amp .i can play little wing and basically with an amp that should tell you more i guess its not the amp or the guitar you have its the size of the theory of how your soul connects with the vibe.help if you can
Hey all - new to the forums, new to Marshall amps and had a few questions about the Code 50 I just ordered that will be here in a day or so. I have played my guitars through my buddy's Code 50 and am familiar with editing the patches, tweaking the tones and getting the sounds that I want from the amp to fit my playing style. What I am not familiar with is the use of footswitch and any Midi capabilities it may have.
1) Can one use just a regular on/off type of old school footswitch to turn an effect or amp on/off or initiate a patch change? I have several old school footswitches I have successfully used on many different amps, albeit older amps, and it has always worked. Curious since the Marshall footswitch actually holds presets if anything like that would work.
2) As far as Midi goes, I come from a Line6 multi-effects world and know that many of their multi-effect units have the capability to control effects on/off/parameters and patch/bank switching via Midi commands. Does the Code software have anything like that if hooked up to a PC/Mac running a DAW that has the capability to send midi control commands to change patches/effects realtime during recording/playback.
Thanks for any input and excited to get this amp. I am a player of over 30 years and have only ever played through Crate amps for the past 20+ years that have finally given up and the cost to repair is more than new. Bash Crate all you want but they were loud and proud and with the right EQ/effects loops made some damn good musical sounds.
Hi I just bought a code 50 and when i try to plug USB cable with my computer (mac pro), evrytime i saw that so it is impossibe to change preset.
I got a Marshall Code 50 a few days ago. It is so much more than I expected. There are more than enough presets to mess with. Some are pretty crappy, but there are abunch of good ones worth tweaking. I've read a lot of comments saying that the amp is crap, the presets suck,etc With so many editing options available, if you can't find the tone you want, you shouldn't be messing with modeling amps. There is plenty of power for my needs, and seems to sound good and consistent through a large volume range.
The stuff I don't like:
1) Why couldn't you use a 1/4" headphone jack instead of the mini?
2) Why couldn't you use a USB normal sized plug instead of miniUSB? You didn't know that miniUSB is almost prehistoric now? I had a tough time finding an adaptor here in Sao Paulo. If I can't easily get ancient technology here in Brazil, the connector must be extinct in the real world.
I've started messing around connecting the amp to my DAW Logic pro and recorded some stuff. It's got potential
I have the My Marshall app paired with my CODE amp. I have my mobile device (Samsung tabket) connected to the amp via a Micro USB cable but still receive the not connected message. I can't download any user presets.
My son has a Code 25 and the preset knob stopped working i had a look at it last night and tried the firmware update from the web site now it wont do anything and just says check USB. has anyone had this problem or have a solution.
thanks in advance
Hi, I’m having trouble getting sound from my Marshall Code 50 amp to record on Audacity.
I am running a new, working USB B cable from my Marshall Code 50 to a Dell Latitude 7280 running Windows 10. The computer is able to detect the amp USB input, and I am using the ‘CODE 50 digtal interface’ as my default recording device on both my soundcard and Audacity, however there is no sound output coming from the amp shown on Audacity , when I try to record (sound is produced from the amp’s speakers, however Audacity is not showing or recording any sound output). I am sure that the connection is working and the amp/ computer is not faulty, as I am able to download tone presets from the MyMarshall preset page. I have tried restarting both my laptop and amp multiple times, using different cables, using different USB ports, AND have the newest 1.41 CODE software, newest Audacity software, and newest version of my Intel HD sound drivers, but to no effect. I am on the verge of going insane from this as I have being trying for over 10 hours, and have had no results. This has worked for me previously, as I last recorded to Audacity with all the same settings about a month ago, however it’s simply not working anymore. I need to get it fixed ASAP, as I am due to record tomorrow, so any help would be greatly appreciated.
I just want to check with fellow CODE users if they are facing the same issues that I am dealing with.
Biggest (and most annoying) issue is, it's a matter of luck connecting the CODE through USB. 2 times out of 10 my pc recognizes the amp the first time I plug it in. Mostly it gives an error that device is not connected properly or not recognized by windows. So I end up unplugging and plugging again until (if ever) it's been recognized. (Using windows 8.1 btw) Then suddenly in the middle of a recording session my DAW starts to drag like if I am running on a PC Pentium 600. (It's running on a 3000$ alienware) This is a sign that somehow CODE get disconnected itself. Now you have only option left: Restart the PC and start all over again.
So far I have checked with different USB cables, and I am using the shortest ones as possible as I can. (less than 80 cm.) I can't check with another pc since I don't have another one, but I am running Yamaha THR-10 smoothly, without any problems at all!
So I don't believe that there's an issue with my pc. And speaking of THR, why the hell CODE doesn't have it's dedicated USB drivers. I am kind of sure that the issue I am facing is all about the ASIO drivers that we are left with as an only option.
Second issue is, maybe only 1 out of 20 times I am able to get any presets from web site. Even if it looks like CODE is connected in the Device Manager, and the Chrome (or Opera) says MIDI is connected, I can't send any presets to the amp. After a few tries, this ends up with web browsers got frozen and only option is again: restart your pc!
I really would like to hear from people who are facing similar issues and how they could get over with it. (if they ever could)
And hopefully the only answer I receive from Marshall team is not going to be: "Thanks for your feedback, we will pass this to our technical team"
Any plans to release a Windows desktop app for managing presets via USB connection? I'm not an Android or iPhone user. Editing via amp panel is ok, but somewhat tedious.
On the code 50 there is an option to edit the presets but this is not on the 25. Is there still a way to edit presets?
Can the usb be used for anything other than recording?