Questions
Showing results 1 to 16 of 16
0

votes

3

answers

26

views

Hi! I have an issue while trying to transfer dowloaded presets to my Code25. It occures both usb and bluetooth connections.  On a usb connection i click the “amp” icon on a preset, it’s name appears on a Code screen. I push and hold store button on amp, “saved” appears. But then Code becomes freeezed, it does not react on button push etc. when i switch it off and then switch on it works fine, preset available on amp. The same issue appears when i try to transfer presets using Gateway app. What I do wrong?

CODE Gateway Bluetooth Presets USB

edited 20 Aug 2019 at 05:44 AM

Alexey Kornilov

asked 20 Aug 2019 at 05:43 AM

Alexey Kornilov
0

votes

10

answers

92

views

Cable plugged in to both computer and Code 50. Display shows 'Ready for Update' - but neither the browser or Desktop Utility will connect.

Rebooted everything and tried from laptop. Same results. What's wrong?

Why can we not update via bluetooth connection rather than USB cable?

CODE Bluetooth USB

asked 07 Jul 2019 at 10:00 PM

Ernie Barnard
2

votes

2

answers

315

views

Actually I'm totaly not interested in bluetooth connection, but of course I understand that it might be an essential prolem for some people...

But there are some other problems I'd like you to find good solution for.

1. Master volume. From 0 to 10% there is almost no sound, over 10% it becomes very loud. 

2. Decreasing sound level with Volume pot results in decreasing USB signal level - not acceptable for players using USB output for recording in DAW software. It would be nice if for clean preamp gain at 2 and volume at 3  give recording level about -6 dB, now it is about -36 dB... 

Best regards, Jacek.

P.S. What is a frequency range of CODE 25 speaker?

 

CODE Bluetooth Speaker USB Firmware

asked 24 Jan 2019 at 11:09 AM

Jacek Klimkiewicz (122)
0

votes

1

answer

213

views

I am experiencing terrible interference when trying to use my Code 50  via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X.  I am using a microphone to record the Code 50 and using the Bluetooth Movies series world to change patches.  The clicks/pops/noise/interference is loud enough to interfere with the recording process.  Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues?   I am running the most current Firmware.  Any current solution to my noise issues? 

Thank you. 

CODE Gateway Bluetooth Mac USB Firmware

edited 17 Dec 2018 at 06:02 PM

Saloni kamalsagar

asked 16 Dec 2018 at 11:46 AM

Saloni kamalsagar
0

votes

1

answer

257

views

Hello, I have acquired the CODE 25, really an excellent amplifier, very versatile and very good presets. My problem and please I hope you help me to resorve it, is that even though I can connect via Bluetooth, I can listen to my tracks ....... the big problem is that when I want to use the FX or presets it appears that there is no amplifier connected ... (either from my android phone or my Ipad I ... I do not understand what the problem is.) Secondly, when I want to install the MARSHALL FIRMWARE UPDATE UTILITY, to enter presets or update the ampli, does not recognize the connection.I request guidance to be able to make full use of such a beautiful tool for my music.I use Widows 10 and G. Chrome.For your attention, thank you very much

CODE Bluetooth iOS Android Presets USB Firmware

asked 16 Oct 2018 at 05:55 AM

Luis Ernesto Espinoza Guerra
0

votes

1

answer

828

views

Is it possible to control and make changes to the existing preloaded patches of the Code App via the USB port connected to a Windows 10 Laptop?

or the Marshall Gateway App works only with Android/iPhone via Bluetooth?

 

thanks

 

 

 

CODE Gateway Bluetooth USB

asked 05 Jul 2018 at 06:58 AM

Mel Gili
0

votes

2

answers

523

views

I connected my Code 50 to my laptop via bluetooth, but the my.marshall presets says "CODE not connected". I tried connecting via USB, but the amp has a goofy connector that standard USB cables do not connect to. Also - I can connect via the Gateway app on my phone, but the presets I add to My Library do not show up (even though it says that they have synced). 

CODE Gateway Bluetooth Presets USB

asked 11 Jun 2018 at 10:11 PM

Tom Appelbaum
0

votes

1

answer

481

views

Hi, my Code 50 USB has stopped working, nothing wrong with the USB port because it still charges the phone - tried two cables, no luck.  So now I'm trying to figure out how to play songs through it via Bluetooth but *&^%%%%### no luck - how the hell do you do it? I've downloaded the Marshall Gateway app to my android but all i get is my phone icon and an arrow to the amp icon. DO I have to do something on the amp?

CODE Gateway Bluetooth Android USB

asked 07 Apr 2018 at 03:31 AM

Leone Britt
0

votes

1

answer

308

views

I'm using the USB connection from a PC to the Code 25, and found that the ouput sound on the headphones is only mono-left mixed.  I get sound in both speakers on my headset, but when I test left/right channels, it's obvious that the sound is only coming from left channel.

This isn't an issue when I'm playing music through the Bluetooth connection, and both left/right channels come through ok.

Is there a firmware fix so that when sound is channeled through USB to the headphone 3.5mm jack, it'd be stereo instead of mono-mixed?

CODE Bluetooth USB Firmware

asked 05 Apr 2018 at 07:59 AM

Alvin Tang
0

votes

3

answers

435

views

I timed it.

I’m not looking for trouble, im just looking for customer service.  I’ve got far better use for my time then sitting on this forum, trolling for answers that will never come—unless YOU, Marshall Amplification changes, which is highly unlikely. You guys are going to be getting a very brutally cold visit from me at the NAMM show!

After going through the entire Blootooth connection process again, which takes like anywhere from 5-10 minutes to get connected, I went to the MyMarshall.com website to download some of the interesting amp models which other users have taken their time to create (thank you to all who have fond this!)  When I download, it goes to my actual login like it’s supposed to, but how do I get it from the mobile device to the amp?  Your video isn’t clear, but do I have to have my device connected to the USB of the amp?  If so, when is the frigging purpose of having Bluetooth then?  If not, what am I doing wrong?

I await for your robotic response.  I’m sure I’ll still be right where I’m at after it comes!

CODE Bluetooth USB

asked 02 Dec 2017 at 01:15 AM

Tommy Naccarato (16)
0

votes

1

answer

283

views

Can I connect to my code 25 via USB to my RCA Voyager tablet cause I can't Bluetooth to work

 

CODE Bluetooth USB

asked 13 Nov 2017 at 01:52 PM

Robert Grisso
0

votes

0

answers

336

views

I cannot use the Gateway app and USB connection together. If my Windows 10 laptop is connect to the amp via USB while the Gateway app is running, it freezes the controls settings in the amp and the app. I still get sound, but I cannot change presets or edit presets on the amp or with the app with the USB connected. I have to disconnect the USB cable to be able to use the app, or the amp controls. If I want to use USB, I cannot use the app. If I want to use the app, I cannot use USB. Any ideas?

I have the latest firmware and latest version of the app. I have tried disconnecting and reconnecting bluetooth connection. I've tried restarting the computer. I've tried disconnectiong Bluetooth, shuting down the amp and the computer, and starting everthing up again. Nothing helps.

CODE Gateway Bluetooth USB

asked 08 Sep 2017 at 08:40 PM

John Pasnik
1

vote

1

answer

530

views

The lag time in the release of this footswitch is rediculous.  Why would you promise something that you can't / don't deliver on?    IF the Bluetooth/iphone Gateway App were usable/seemless, the physical footswitch might not be necessary.  IF the parameters of the amp (including up/down patches) were avaiable via the USB port to a Computer program/app, the physical footswich might not be necssary.  IF there weren't Bluetooth and other software bugs, then the physical footswitch might not be necessary.  Unfortunately, IT IS necessary just to use the Code 25/50 remotely as was promised in it's advertising when purchased. Mine is still under Warranty by Marshall.   It is not performing as advertised.  Please send footswitch, or send me a RMA (Return Merchandise Authorization) for the whole AMP  - you pay return shipping...   

CODE Gateway Bluetooth USB Footswitch

asked 18 May 2017 at 01:58 AM

S Fisher (6)
1

vote

1

answer

843

views

Promises, promises ... "we'll fix it soon";  " bluetooth issues will be addressed in future firmware updates";  " USB recording issues will be looked into"; AND, a 2-way footswitch will be available for Code 25/50 users when Code 100 is released.  Am I alone in my disappointment for Marshall's seemingly apathetic (non) responses to purchasers of their "not ready for prime time" digital products?!?!?!   I really wanted a Marshall Amp after 45 years as a Fender user.  My mistake.  I should have known better.  Useless, unsupported, glitched, buggy, unreliable, etc., etc., etc.    What say you Marshall in an attempt to save any reputation you thought you had?!?!?!?

CODE Bluetooth USB Footswitch Firmware recording

asked 05 Apr 2017 at 06:08 AM

S Fisher (6)
0

votes

1

answer

514

views

So...just got my new code 25 the other day and bluetooth hooked up great....played a couple of days and no problems....Tonight..cant get it to hook up.  Any ideas?...Can I ultimatley just hook up USB to my computer and adjust fromt there?

CODE Bluetooth USB

asked 13 Sep 2016 at 12:39 AM

Scott Bojanich
2

votes

3

answers

2.3k

views

I am experiencing terrible interference when trying to use my Code 50  via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X.  I am using a microphone to record the Code 50 and using the Bluetooth to change patches.  The clicks/pops/noise/interference is loud enough to interfere with the recording process.  Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues?   I am running the most current Firmware.  Any current solution to my noise issues?  Thank you. 

CODE Gateway Bluetooth Mac USB Firmware

asked 05 Sep 2016 at 05:35 PM

S Fisher (6)
Showing results 1 to 16 of 16
Loading - please wait...