Questions
Showing results 1 to 10 of 10
0

votes

1

answer

107

views

I seem to be having the same issues that a lot of people have reported, where I cannot get the Marshall Gateway app to connect to my Code 25. I've only had the amp for about a week and I cannot get the app to see it. ? 

I can connect to the amp via Bluetooth using my phone (Pixel 3a, Android 11) and whilst connected, can use it as a BT speaker to play music from Spotify. However, nothing I do seems to get the app to connect to the amplifier. 

-I've updated the amp to the latest firmware using my laptop/web browser. 
-I've followed all the instructions in the Bluetooth Connectivity Troubleshooter to the letter (CODE - Gateway Bluetooth Connection Troubleshooting - my.marshall.com)

No matter what I do, or what order I install/uninstall/connect, the app will not see the amplifier. Everything works otherwise - I'm able to apply Patches from ? using a USB connection - and the amp sounds great. I'd just like to be able to control it from my phone.

edited 03 Oct 2021 at 01:11 AM

Harleigh Maguire

asked 16 Sep 2021 at 03:16 AM

Harleigh Maguire
0

votes

2

answers

199

views

I have a xiaomi redmi note 8 and also have a problem connecting the marshall gateway app to the amp code50.
I can only be connected as if I were listening to music, I even tried to connect it with an otg adapter, it works like that, but there are a lot of problems with braking the application? Please if it is possible to solve this problem.

 And if I tried all variants except one, and that is to uninstall every marshall application to amplify my Marshall Code 50 Firmware 1.4.4 recognize bluetooth connection from which I can control my installed Gateway 1.5.5 of course not just music to listen to But that I have complete control and whether maybe the problem is that the usb is included in my computer, whether to turn it off because I registered everything else. If anyone can answer all these questions I will be grateful.

asked 08 May 2021 at 09:33 AM

Vladimir kovacevic
0

votes

1

answer

299

views

Hi, I just recieved my Code 50 yesterday "bought brand new" and the amp sounded great until i hooked up to my pc this morning and downloaded a featured preset not a communiy preset. I am running usb not bluetooth and its my studio setup. Now all the distortion and gain sounds like the input gain is wide open clipping the signal coming in at all volume levels, and on all distortion and od gain presets. I tried to reset the amp and did a firmware update now its litterally so bad you cant play it. This is certainly a software issue cause the effects and clean tones sound fine. This happened immediatley after i sent the preset usb from the website to the amp from the pc. Also i tried several guitars, usb cables, guitar cables and even my mac. just dont know wether i should send it back or if thiscan be fixed with a firmware patch or something , Thanks

asked 09 Mar 2021 at 07:41 PM

stephen anderson
2

votes

2

answers

952

views

Actually I'm totaly not interested in bluetooth connection, but of course I understand that it might be an essential prolem for some people...

But there are some other problems I'd like you to find good solution for.

1. Master volume. From 0 to 10% there is almost no sound, over 10% it becomes very loud. 

2. Decreasing sound level with Volume pot results in decreasing USB signal level - not acceptable for players using USB output for recording in DAW software. It would be nice if for clean preamp gain at 2 and volume at 3  give recording level about -6 dB, now it is about -36 dB... 

Best regards, Jacek.

P.S. What is a frequency range of CODE 25 speaker?

 

asked 24 Jan 2019 at 11:09 AM

Jacek Klimkiewicz (170)
0

votes

1

answer

577

views

asked 01 Jan 2019 at 07:30 PM

James Graham (12)
0

votes

1

answer

772

views

I am experiencing terrible interference when trying to use my Code 50  via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X.  I am using a microphone to record the Code 50 and using the Bluetooth Movies series world to change patches.  The clicks/pops/noise/interference is loud enough to interfere with the recording process.  Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues?   I am running the most current Firmware.  Any current solution to my noise issues? 

Thank you. 

edited 17 Dec 2018 at 06:02 PM

Saloni kamalsagar

asked 16 Dec 2018 at 11:46 AM

Saloni kamalsagar
0

votes

1

answer

596

views

Hello, I have acquired the CODE 25, really an excellent amplifier, very versatile and very good presets. My problem and please I hope you help me to resorve it, is that even though I can connect via Bluetooth, I can listen to my tracks ....... the big problem is that when I want to use the FX or presets it appears that there is no amplifier connected ... (either from my android phone or my Ipad I ... I do not understand what the problem is.) Secondly, when I want to install the MARSHALL FIRMWARE UPDATE UTILITY, to enter presets or update the ampli, does not recognize the connection.I request guidance to be able to make full use of such a beautiful tool for my music.I use Widows 10 and G. Chrome.For your attention, thank you very much

asked 16 Oct 2018 at 05:55 AM

Luis Ernesto Espinoza Guerra
0

votes

1

answer

821

views

I'm using the USB connection from a PC to the Code 25, and found that the ouput sound on the headphones is only mono-left mixed.  I get sound in both speakers on my headset, but when I test left/right channels, it's obvious that the sound is only coming from left channel.

This isn't an issue when I'm playing music through the Bluetooth connection, and both left/right channels come through ok.

Is there a firmware fix so that when sound is channeled through USB to the headphone 3.5mm jack, it'd be stereo instead of mono-mixed?

asked 05 Apr 2018 at 07:59 AM

Alvin Tang
1

vote

1

answer

1.5k

views

Promises, promises ... "we'll fix it soon";  " bluetooth issues will be addressed in future firmware updates";  " USB recording issues will be looked into"; AND, a 2-way footswitch will be available for Code 25/50 users when Code 100 is released.  Am I alone in my disappointment for Marshall's seemingly apathetic (non) responses to purchasers of their "not ready for prime time" digital products?!?!?!   I really wanted a Marshall Amp after 45 years as a Fender user.  My mistake.  I should have known better.  Useless, unsupported, glitched, buggy, unreliable, etc., etc., etc.    What say you Marshall in an attempt to save any reputation you thought you had?!?!?!?

asked 05 Apr 2017 at 06:08 AM

S Fisher (6)
2

votes

3

answers

3.2k

views

I am experiencing terrible interference when trying to use my Code 50  via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X.  I am using a microphone to record the Code 50 and using the Bluetooth to change patches.  The clicks/pops/noise/interference is loud enough to interfere with the recording process.  Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues?   I am running the most current Firmware.  Any current solution to my noise issues?  Thank you. 

asked 05 Sep 2016 at 05:35 PM

S Fisher (6)
Showing results 1 to 10 of 10
Loading - please wait...