Questions
Showing results 1 to 5 of 5
0

votes

1

answer

26

views

I have a two part question 🤔.  I have my two amplifiers listed above.  I have both electric and electric acoustic guitars.  I'm learning how to play and bought the 50 watt acoustic Amp as I  really like the sound of over wound humbuckers through it for heavy slow blues.

First question,  keeping the AS50D as the main sound, can I connect it through/to the 100 watt Marshall? Both are 4 ohms and I would like the maximum amount of power to drive my 4 x 12" cabinet of 8 ohm Jensen Tornadoes that are wired in series for the 4 ohm 100 watt MG HDFX. Then I would have 150 watts total to drive my 400 watt total limit.

 

Question two,  can I connect my 50 watt AS50D Amp to my 4 x 12" speaker cabinet by running a cable from the back of my Amp to the cabinet. I have footswitch,  line out and (effects loops) send and return Jack's to use.

  Even though my 4 x 12" cabinet would be very under powered. I would like to hear the sound of the AS50D  through those speakers. I'm new to guitar and don't want to ruin any of my equipment.  I did also have a guitar made through two luthiers,  I also made the 4 x 12" cabinet to match my guitar.  I call them Snort and the box.

  I have the components for the sound I'm looking for,  now I need to combine them all together.  I truly appreciate guidance from the technical support team at Marshall. 

God bless you for your time and kindness.  Thank you,  Eric Dailey 

asked 06 May 2022 at 09:49 PM

Eric Dailey
0

votes

0

answers

584

views

I was wondering if the creator of the KASHMIR preset would be interested in also creating the FLANGER part for KASHMIR using all the current preset settings (amp, cabinet, speaker etc) as a complimentary preset for the turnaround section of the song.  I believe, from forums, that a preset will switch better (Marshall CODE footswitch) if the preset has the same amp, speaker and or cabinet setting as it takes away the millisecond delay of switching between amps in a particular preset.  Look forward to your answer and or creation of said beasty.

Regards Kev

 

asked 30 Jul 2019 at 02:07 AM

Kev Lawlor
1

vote

0

answers

1.3k

views

Why does my code 50 amp cut out? Also, has loud crackeling sound when it's working. Sounds like a blown speaker but it's not. The master volume is only turned up 1/4 of the way and it's loud. Problems still remains even at lower volume. slight delay on the footswitch also when changing from one preset to another. Frustrated in Detroit.

asked 02 Feb 2018 at 04:55 PM

Craig Truran (1)
0

votes

1

answer

1.1k

views

Purchased used amp, jcm 2000 tsl 100 2003 with 2003 1960a slant cab. Bought footswitch, being shipped. my questions are 1) will dsl 100 cover fit my tsl 100   2) where can i get replacement tubes 3) Can i get paper manuals for amp and cab    4) is there a rt angle speaker cord available

asked 11 Oct 2017 at 12:58 AM

martin peters
4

votes

0

answers

1.3k

views

Presets need to flow easier between the different management areas.

(Reading the following is really only cumbersome, because that's how cumbersome it is to manage CODE.)

Copying one by one between amp and phone is really cumbersome.
How about an option to copy all 100 presets (or sections) between amp and phone? Both ways.
I want my amp to have the same presets as my phone.
(Others can still have the option the way it is laid out, but I don't see how managing amp and phone separately is useful unless someone really needs 200 different presets in one session.)

I like to have my preset sequenced in a way that makes sense. Artists, cleans, crunch, OD, Amps, or new additions squeezed next to existing ones. Others may sequence by set list or bands. If I shuffle presets on the computer/gateway, then the phone syncs this new sequence, and the amp does not match. Gets confusing.
Additionally, if the footswitch is assigned from the amp, then I have to copy new presets from phone to amp and even reassign to footswitch. Too many steps.

"Just use the presets on the phone and forget amp presets" would be an answer, but what about footswitch? and what about dead or forgotten phones?
Easy (automatic?) sync (with on/off for this auto/sync) between phone and amp, would allow everyone to use the amp (and footswitch) without constantly pulling out the  phone and pairing to have presets from the phone available. Bluetooth drains batteries.
Btw, any phone sounds come on the speaker  when playing because my iphone6 sees the amp as a headphone. So the presets need to be on the amp for any gigs.

Another footswitch suggestion:
A setting or function where the first 30 presets (01-30, without 00) are loaded into the 10 banks on the footswitch automatically? Then I only have to manage my presets within the 100 and everything else is assigned automatically?

asked 18 Jun 2017 at 07:02 PM

michael s (9)
Showing results 1 to 5 of 5
Loading - please wait...