Questions
Showing results 1 to 20 of 90
0

votes

0

answers

37

views

hi all,

I ve got a helix hx I am trying to use for channel swap on the amp.

 

For all of the above the following applies:

- JVM footcontroller is disconnection

- JVM midi has been reset: its on MIDI channel 1

 

Boss ES5 (works)

I can get it working using a Boss ES5: https://www.youtube.com/watch?v=3YI65cgA4XI

Midi cable setup: Boss ES5 (out)  > JVM (IN)

 Also going from Boss through the helix (midi passthrough works).

Midi cable connection:  Boss ES 5 (out) > Helix (IN) > Helix (out) > JVM

However, this is using Midi patch panel change. Not sure how this differs from MIDI CC?

 

Helix HX (not working)

For Helix im following this video : https://youtu.be/simaPS7dzLw?t=55

Midi cable connection:   Helix (out) > JVM

Im using MIDI CC and following the table in JSH User manual.

channel : 1

Function: CC: 16

value 2

= clean channel, Orange mode.

 

I set the amp up so that the midi controller is BLINKING and it doesnt stop blinking: its not receiving the signal?

I feel like Im close to getting there.

 

Any ideas?

Thanks,

Eric

Presets Manual MIDI

asked 28 Jul 2019 at 09:07 AM

eric barlier
0

votes

1

answer

35

views

can i get a manual for my 1923 jim marshall obe 85th celebration special edition 50 watt head? 

Manual

asked 15 Jul 2019 at 11:36 PM

Donny Lovette
0

votes

1

answer

89

views

Hello

I want to exchange valves in my Origin 20h, ordered some from Tube Amp Doctor. After I exchange them do I have to rebias it? Is there a manual for rebiasing? I wasn't able to find anything which would give me even slight bit of a hint about it .

thanks

iosman

Manual Tubes

edited 06 Aug 2019 at 07:59 AM

ios man

asked 07 Jul 2019 at 06:13 AM

ios man
0

votes

1

answer

87

views

I just got this head recently and installed the latest firmware update the other night (6/20/2019).   When I try to connect my IPad through the My Marshall app it seems to be a hit or miss proposition but more miss than hit.   In my settings on the IPad it shows me as connected, and the blue light on the head goes from flashing to solid.  On the app, it shows the head detected but when I press on that I get a "Connection Rejected"  (You may only control amps you are already connected to for audio output) and there's no control over the head from the app.   Now several other times it syncs right up.  I'm at a loss though.  Am I doing something wrong maybe in the sequence (operator error) or is there an issue somewhere else.  The manual doesn't really reference Bluetooth that well.  I'm not bluetooth savy becuase I rarely use it except for my phone in the car and connection there is automatic after I initially set it up.

So is it me?  Is it the gateway software?  Is it the head??   Help please?

CODE Gateway Bluetooth iOS Manual Firmware

asked 22 Jun 2019 at 05:32 PM

Kim Lubstorf
0

votes

2

answers

120

views

I just got around to updating the firm ware on the code 100 thought as long as i had the amp connected to my pc via the usb cable I would check out the code editor and it would not respond looked at the manual casually and did not notice any mention of how to connect

 

dos this need to be acomplished using a midi to usb cable

CODE USB Manual MIDI

asked 18 Jun 2019 at 01:46 PM

Stephen Rosin (1)
0

votes

1

answer

87

views

I really need the above to repair my Marshall MG30CFX  guitar amp. Can the forumers point me to the right place to download it?

Manual

asked 04 May 2019 at 08:38 AM

Athan Kopar
0

votes

0

answers

104

views

Hope this helps some folks. The registration and Web site is a joke. Shame on you Marhsall !

https://marshall.com/marshall-amps/products/archive

Registration Manual

asked 04 Mar 2019 at 01:21 AM

Mark Mitchell
0

votes

1

answer

152

views

Hi guys,

I want to exchange valves in my Origin 20h, ordered some from Tube Amp Doctor. After I exchange them do I have to rebias it? Is there a manual for rebiasing? I wasn't able to find anything which would give me even slight bit of a hint about it...

Manual Tubes

asked 10 Feb 2019 at 04:21 PM

Stepan Dusek
0

votes

1

answer

134

views

Is the a Marshall Forum for all types of Amps or just Code amps?   I need a user manual for a JVM 205H.   Where on Marshall's web page do  i go please?

 

thanks

 

CODE Manual

asked 09 Feb 2019 at 07:46 PM

Ronald Spurgeon
0

votes

0

answers

150

views

Hello,

Reading the manual for the Code 50, it's not clear to me what the tap pattern setting is on the multi delay. What I am tryng to do is emulate having two delay pedals, essentially just repeating twice with no feedback. The effect should be two "echos" of a note and then nothing more. The multi delay seems to work, the manual says to set the Feedback level to the number of delay repeats (2). The Tap Pattern function seems to have no effect, though. How is that supposed to work?

Thank you.

CODE Manual Delay tap pattern multi

asked 05 Feb 2019 at 10:41 AM

Daniel Stux
0

votes

1

answer

141

views

Searching all over the interwebs for a Marshall G15MS Micro Stack Amp Manual (not the G15MSii version). My amp does not include the Overdrive button.

Can anyone help?

Manual

asked 16 Jan 2019 at 05:57 PM

Adam Filiatrault
0

votes

2

answers

128

views

Hi, 3 question:

1) I'm Italian and I just purchased on ebay a brend new DSL40Cr from a UK shop. I was wondering if the ampli still works at 220V - 50 Hz as per manual, regardeless the fact it comes from UK, and if will arrive with power calbe schuko plug or UK plug. In this case may I use an adaptor male shuko/female UK ?

2) I would like to know if I can use an external speaker as additional together with the internal Speaker, for example the internal 16 Ohm speaker + an external 8 Ohm speacker connected obviously at right socket.

3) in case of use of one external speaker (e.g. 8 Ohm ) which one I should connect of the two socket where is labeled down "1 x 8 OHM - 2 x 16 OHM" ? is it indifferent, the one to the left or the right ?

update for the question n.2: maybe I figure out how it has to be done: unplug the internal speacker from 16 OHM socket and plug it into the 8 OHM speacker. plug a 16 OHM external cabinet into the other 8 OHM Speacker socket. otherwise only configuration showed on manual are allowed. Is that correct?

 

thank you

Speaker Manual ExternalSpeaker Power dsl40cr Cable

edited 15 Jan 2019 at 01:35 PM

Roberto ACErob71

asked 15 Jan 2019 at 01:06 PM

Roberto ACErob71
0

votes

0

answers

117

views

Hi people.

Firstly, I would like to say what a great site.

Secondly, forgive me if this has been asked elsewhere.

Ok, the question is:

I have a Marshall origi n 50 head(beautiful bit of kit!!!!)

And a marshall 1936 cab.

The issue i have is which speaker connections to use.

The manual forvthe amp says socket 3 at 8 ohms, yet the back of yet amp shows socket 2 as 8 ohms!!!

Also even though amp is not stereo can i use 2 speakef cables ftom the 16ohm sockets????

A bit crazy i know but dont wznt to blow me new amp for the sake of asking the great znd wise

Many thanks in anticipation

Speaker Manual

asked 14 Jan 2019 at 11:32 PM

PATRICK BENNETT
0

votes

1

answer

148

views

When I try to save a preset to the amp, there is no problem. When I try to save a preset to my library I get the message: Patch cannot be saved; sync with Marshall server in progress.  My gateway has both a Bluetooth and an internet connection. Logged into my.marshall but nothing happening. Sync button is disabled. I feel like I'm missing something in my understanding of this aspect of the Code/Gateway system. Is there a user manual for the Gateway app?

Gateway Bluetooth Presets Manual

asked 12 Jan 2019 at 02:16 AM

David Miller
0

votes

1

answer

243

views

I have a Marshall DSL 100-watt head purchased in 2016 (so not the newest version), whose channel switching and onboard reverb I would like to operate with a Fractal Audio FX8's relay function. The manual for the FX8 clearly states that its relay function is only to be used on amps with "short-to-sleeve" switching. My questions are, is the Marshall DSL100 head built with short-to-sleeve channel switching? And also, do the channel switching and reverb on/off functions on the amp behave in a latching manner (i.e. the effect remains on as long as the switch is engaged) or an auto-off manner (i.e. the effect is triggered by a momentary connection)?

Thank you!

Footswitch Manual DSL

asked 08 Jan 2019 at 06:59 PM

Hayden Gist
0

votes

1

answer

214

views

I've read the manual and apparently the volume knob controls the volume of whatever preset is selected.

I'm running a Marshall code 50 with boss gt1 pedalboard so my question is, if i want to my sound to be controlled via pedalboard shouldn't I be able to turn volume knob all the way down and only control the amps volume with master volume knob? Because the moment i turn the volume knob down i dont hear anything.

I'm just trying to get a more deeper sound, the sound i get is just way too bright

CODE Presets Manual

asked 29 Dec 2018 at 08:02 PM

Brandon Parish
0

votes

1

answer

128

views

I cannot know some menu. for example, how touse a small icon that is described tablet mark and amp mark.

I want to know detail of Gateway Application.

How can I get the detail manual about application on tabet?

Gateway Manual

asked 02 Dec 2018 at 04:17 AM

Morimasa Matsuda
0

votes

1

answer

183

views

Ive read the manual for the jvm410h but dont fully get the outputs.

All i need to know if anyone can help it what out puts do i use on amp and cabs when i plug into my 1 1960a and when i use my 1960b too so half stack full stack.

I need idiots guide.

Thanks 

Speaker Manual

asked 06 Oct 2018 at 07:18 AM

Paul Evans
0

votes

1

answer

168

views

Hello, 

I'm about to buy DSL20CR, I'd like to verify that my Line6 helix can switch channels and enable / disable fx loop of that amp.

In Helix manual is said: "IMPORTANT! Connect EXT AMP 1/2 only to amplifiers that utilize "short-to-sleeve" footswitch inputs. Connecting to any other sort of input could cause permanent damage to both your amp and Helix! If you're not sure if your amp has short-to-sleeve inputs, contact the manufacturer."

Is this ok with DSL20CR?

 

br, 

Martti

Footswitch Manual

asked 02 Oct 2018 at 04:08 PM

Martti Väisänen
0

votes

1

answer

210

views

I've been playing Marshall amps for years now and I've bought new and used, traded for them, traded them away for other stuff, and Marshall USED TO SUPPORT us out here in the REAL WORLD that keep their amps going and keep playing them by making the owners manuals available on the website and making the website easy to navigate but now it is a complete disgrace!!!!!  How F***ing hard is it to keep the owners manuals linked to an easy to locate section UNDER what USED TO BE CALLED "SUPPORT"!!!  It is not very hard at all.  The only manuals I can navigate to are the CODE amps.  You should be proud to support your vintage amps and keep the manuals fully available online for your time honored and time tested LOYAL CUSTOMERS who continue to use Vintage or Older Model Marshall Amps.  Your Website sucks now and is extremely limited.  I realize you want to keep your current products out there and is no way you can continue to host all of your product specs and info on so many models over the years, but YOU COULD continue to maintain the ONE page in a SUPPORT section that details where to download your DISCONTINUED PRODUCTS and simply throw all of those PDF files into a folder and link it to your SUPPORT page so we can continue to download the manuals easily ourselves without any assistance from you guys.  It doesn't take up that much disk space and is not very hard at all to encode that back into your page.  I am SURE that I am not the only one here that is completely frustrated that Marshall Customer Support appears to have gone to hell and you don't seem to care about your customers any longer or you want to SELL us a manual to get more money out of us.  This is CRAP!  You need to FIX THIS and I guarantee you that Millions of Marshall USERS will thank you!  Let's get back to putting the Customer FIRST folks!  

CODE Manual

asked 02 Oct 2018 at 01:54 AM

Dale Ellerbe
Showing results 1 to 20 of 90
Loading - please wait...