The continuous scrolling of the display, plust the lag when I turn the knob make it very difficult to read the display. Am I missing a trick? Do they all do this?

Buenas amigos.

Tengo el CODE100 via USB conectado a mi PC. Mi PC detecta el CODE 100, pero cuando entro en Reaper no puedo activar mi guitarra para escucharla en Reaper. Alguien me puede ayudar y darme paso a paso, desde que arranco el Reaper y mi CODE 100 esta conectado y lo detecta para que suene y pueda grabar la guitarra. Puedo escuchar las otras pistas grabadas (baterias, bajos, voces ) pero al querer escuchar mi guitarra no puedo.

Seguramente hay pestañas de Reaper, o tema de drivers, o no se que, que no hago bien. Tambien me dice que Reaper no puede hacer "enabled" mi CODE.

Mucha gracias

I have successfully saved presets to my iPhone and can play them using the bluetooth pairing.

What is the best way to permanently transfer or sync them from the iPhone to my Code 50 amp? 

Hello,

I had purchased a marshall code 100C. After a marshall dealer told me there was a fire hazard issue with the code 100C and that the code 50 was better i sold the 100C and bought the 50C now i see it doesnt have an effect loop. IS this true with a defect in the code 100 combos or is there a new version coming. IS the marshall code 50 a better product?

Warren

Hello everyone. I recently purchased a used Marshall Code 100 amp. It sounded great at home and at rehearsals I had it on a milk carton a couple of times and sound was still good. Then, I put it on an amp stand which put it at about my chest level. The sound has now seemed to completely change. The sounds are more tinnier (even with a Les Paul) and lower strings on my telecaster can sound muddier on some settings. Can this much sound difference happen with the position? Anyone else have this amp and run into this problem? is there something wrong with the amp? Thanks!

Hi, I've been trying to record using the CODE 25 connected by USB to my PC but have been getting really low volumes in Audacity. Preset volume is already set to 10 and output from the speakers are already loud. Is there a way to increase only the volume of the USB audio output without increasing master volume? Thanks.

I need help with the code footswitch 

all I want to do is click one footswitch button to go from one preset(clean) to a overdrive preset  

like set the code 50 on 87 then hit the switch to like 50 or whatever. 
thanks in advance for the tutorial for me, tye moron. 

Hello,

I purchased a marshall code 50 in the USA from Guitar center in Jan of this year. Now, there is an issue where the sound from the amp speaker cuts off after 15-20 seconds of plugging my guitar in. I can still hear the guitar if I use any headphones. Upon contacting the store they suggested to contact Marshall directly since there wasn't a specific type of coverage on the amp I purchased. So my question is how can i contact marshall USA to get this resolved? It doesn't seem super straightforward to find their info online. Any help would be appreciated.

Thanks,

Kshitij

Hello everyone from Portugal,

I recently bought a marshall code 50 and I am really dissapointed. Any tips for making it sound better? I have spend ages on it trying to get a good high gain tone but it just sounds 'boxy'. Any help would be greatly appreciated.

Does anybody have a list of the cabs and descriptions, and also more detail on the effects options? Perhaps I am a loser because I don't know all the historical Marshall speaker cab configurations or know what CLS means on a chorus effect :-)  But I don't. A list would be helpful.

I just replaced my old Line 6 Firehawk setup with a Marshall Code 50. I am still figuring out the settings and how they interact but it is definitely an upgrade and a bargain for the money. Line 6 did publish a comprehensive list of amps, effects and cabs though, with detail on what each model was based on, and this was both interesting and helpful. 

This has been asked before and the answer was to search the marshallforum.com, and I did but found nothing.

I have an issue with tap tempo on the Code 25 with 1.45 firmware and wondered if anyone else has the same issue.  The manual says you should "press MOD and DEL selection switches together". When I do that the amp does indeed go into tap tempo mode (tap the selector switch to set tempo), but regardless of how quick I press the buttons or if I hold down one and then hit the other it always switches on the MOD module too. The other double combination switches (tuner and bluetooth) dont do this and work as expected and only switch on those functions without switching on or off any other modules.

Many people are talking that the new CODE products with current manufacturing dates are already coming from the factory with the new Firmware 1.45, and that it brings many improvements and the equipment sounds better than with the 1.44 which is the last officially launched.

Please release this new 1.45 as soon as possible or at least let us know when its release is estimated on the official website Thank you

I need to change the order of the presets as needed, but the Gateway application does not allow changing the position of each preset in memory. 
I don't want to overwrite presets by saving to other stots, I just want to change the order of each preset. 
Is there another way to perform this operation? 
MyGateway does not synchronize with the hardware, it only sends it to the hardware. 
My CODE presets do not appear on MyGateway.

Hi, 

I have a CODE50 (1 week).

After editting a preset, I click and hold the exit/store button to save the changes I made.   The changes are stored but the CODE then "freeze"..  no sound, no change possible,...    After switch off/on, everything is back to normal.  The preset is updated.    

Same thing is happening when I store the preset in the footcontroller...  

Is that "normal"?   Am I doing something wrong?   I presume that I'm not supposed to do a switch on/off everytime that I want to store a present change...   

Thanks

I seem to be having the same issues that a lot of people have reported, where I cannot get the Marshall Gateway app to connect to my Code 25. I've only had the amp for about a week and I cannot get the app to see it.

I can connect to the amp via Bluetooth using my phone (Pixel 3a, Android 11) and whilst connected, can use it as a BT speaker to play music from Spotify. However, nothing I do seems to get the app to connect to the amplifier.

-I've updated the amp to the latest firmware using my laptop/web browser. 
-I've followed all the instructions in the Bluetooth Connectivity Troubleshooter to the letter (CODE - Gateway Bluetooth Connection Troubleshooting - my.marshall.com)

No matter what I do, or what order I install/uninstall/connect, the app will not see the amplifier. Everything works otherwise - I'm able to apply Patches from ? using a USB connection - and the amp sounds great. I'd just like to be able to control it from my phone.

I suddenly have this problem with my Code 50 and my Lenovo tablet. It did work with the Gateway app until today, and it is connected via bluetooth and it will play music from the tablet, but the Gateway app doesn't even see the amp. I tried uninstalling it, reinstalling it, clearing the cache and storage, no joy. Oddly, it works fine still from my LG phone.

I have 2 cabs,   2x12(16 Ohms 100w) and 4x12(8 Ohms 240w).

In Code 100h manual, says the speaker output is MINIMUM 8ohms load. I can use my 16 ohms cab without harm the amp head or the cab itself?

I'm getting trouble in the 4x12 transportation, the 2x12 is way lighter. Until now I'm only using the 8Ohms cab in the code 100h.

Here are a few things I would suggest as improvements to the Marshall Code series. I have a 25 so some things may be specific to that amp. I have stuck to things that could be improved only by software or firmware as these are improvements everyone can have simply by updating the firmware rather than modifying the amp itself.

1. Reduced power mode to switch between full power and lower power mode. This would fix the volume control issue everyone complains about.  Maybe this could be a global setting in the firmware ?

2. USB audio Volume level setting (e.g.  -3dB, 0dB, +3dB etc). This could also be a global setting in the firmware ?

2. Normalise the volumes of the models, some are way too hot (British class A power-amp), some are way too low (Natural pre-amp). I beleive this is the reason why some models have strange low frequency distortion (50s British, OD DSL).

3. Show the configuration of the Cab models, not everyone is a Marshall fanboy and I have no idea what cab a "1960X". even if it was displayed as "1960X (4x12)" I would at least know what the configuration of cab the model is.

4. Fix the spring and hall reverbs, they sound very cheap, like the "echo" you would get on a cheap karaoke machine, certainly nothing like a spring reverb.

5. For god's sake release an official desktop editor!!! with the option to save/restore/edit patches.

6. A sync button to sync the amp presets with your gateway. It you want to rearage the patches online in gateway, you have to manually save all the patches one at a time to the amp using the phone app. So if you add a new patch at position 0, you have to manually save all 100 patches one at a time in order to match your gateway sounds!

 7. Fix the tuner, it is pretty bad on both the amp and the app. It's slow to respond and not very accurate (at least thats what its like on mine). Ive no idea how well it works on the foot controller.

8. If possible add a Fuzz pedal model, even at the expense of removing another model (I wouldnt miss the pretty poor Acoustic simulator for instance).

These are just some suggestions that I feel would make the amp just a little bit better, but in general I'm having a lot of fun with this little amp, and love the sounds and features it has. It is way better sounding than some of the negative reviews online would suggest.

Maybe other people can suggest firmware updates too?

As title says I have no output to the speaker cab. All I hear is a very quiet fizz/hum. Output to headphones is fine. Only arrived today and will be going back Monday unless I can resolve this. Code 2x12 cab seems fine and tried three different speaker leads. Gutted as I was so looking forward to getting a full weekend on this before going back to work.