Hi, I just recieved my Code 50 yesterday "bought brand new" and the amp sounded great until i hooked up to my pc this morning and downloaded a featured preset not a communiy preset. I am running usb not bluetooth and its my studio setup. Now all the distortion and gain sounds like the input gain is wide open clipping the signal coming in at all volume levels, and on all distortion and od gain presets. I tried to reset the amp and did a firmware update now its litterally so bad you cant play it. This is certainly a software issue cause the effects and clean tones sound fine. This happened immediatley after i sent the preset usb from the website to the amp from the pc. Also i tried several guitars, usb cables, guitar cables and even my mac. just dont know wether i should send it back or if thiscan be fixed with a firmware patch or something , Thanks
The iOS Gateway app was unable to connect to my CODE 50 even though my MacBook Pro is connected via bluetooth, so I did a factory reset and then tried to do a firmware update. The first part of the firmware update (1.44) appeared to install correctly. Next I saw a DSP update and tried to apply that update. In the middle of the DSP update, I received an error message to the effect that the update failed and I should power off & on my computer/device. I powered my Mac off & on, but the CODE 50 shows a progress indicator (about 20%) and says "DO NOT SWITCH OFF."
I tried to reinstall the firmware/DSP update, but this time the update process would not even begin. I suspect the problem is the frozen progress indicator and whatever ongoing or frozen process is causing the "DO NOT SWITCH OFF" message.
Othe than ignoring the warning on the CODE 50 and powering it off & on, I don't see what else I can do. Is there a way to abort the ongoing or frozen process without turning the CODE off.
What should I do?
I bought the combo yesterday and it's full of bluetooth bugs - looking now at the FORUM my impression is that the support doesn't care about it.
- No automatic bluetooth connection - iPHONE - I am having always to force Iphone to "forget" the AMP and pairing it again... each time...
- MAC IOS , When I try to connect the bluetooth in my MAC, it makes the system crashes, mouse and keyboard stop working... there's no were to get the necessary code to bluetooth connection...
DO WE HAVE PLANS FOR A NEW FIRMWARE TO BE RELEASED SOON ? PLEASE
I am experiencing terrible interference when trying to use my Code 50 via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X. I am using a microphone to record the Code 50 and using the Bluetooth Movies series world to change patches. The clicks/pops/noise/interference is loud enough to interfere with the recording process. Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues? I am running the most current Firmware. Any current solution to my noise issues?
I recieved my Code 100H this week.
(FYI) I attempted the update with a MacBook Pro with USB-C, High Sierra 10.13.1, Chrome Browser. I was able to connect to the Code but the unit would not update. It was stalled on the progress bar on the unit at 0% and on the browser.
(FYI) I attempted the update on a Windows machine and was successful using the update utility and with Chrome Browser. The Code unit shows updating to 1.4.1 but the boot screen shows 1.11?
The Code 100H will not connect to any Bluetooth device I have. Windows, Mac, iPhone, or iPad. It does not even show up as a device and never has even out of the box. I am convienced it does not work. Is there a master reset button combo for the unit? I am out of ideas concerning the Bluetooth. It seems like I am not the only one having issues with the Bluetooth. If this can't work consistently I am considering returning the unit. Even the simplest device can connect with Bluetooth and hold a connection. My Code 100H won't even show up as a device to connect to. Please advise.
I am experiencing terrible interference when trying to use my Code 50 via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X. I am using a microphone to record the Code 50 and using the Bluetooth to change patches. The clicks/pops/noise/interference is loud enough to interfere with the recording process. Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues? I am running the most current Firmware. Any current solution to my noise issues? Thank you.