Questions
Showing results 1 to 20 of 69
0

votes

1

answer

76

views

The Marshall Code 50 I bought losses sound while in use. Turn the power on and off sometimes fixes it and also disconnecting it from the bluetooth device. However, recently I don't even connect a bluetooth device like my phone to avoid it, it still happens. Already tried installing the lates firmware, done factory reset, and still having this problem. I'm from the Philippines, the seller did not reply when I asked for assistance. I also don't know where I could bring it for technical support.

asked 04 Nov 2021 at 07:16 AM

Roger Brigido Lagatic
0

votes

1

answer

156

views

I seem to be having the same issues that a lot of people have reported, where I cannot get the Marshall Gateway app to connect to my Code 25. I've only had the amp for about a week and I cannot get the app to see it. ? 

I can connect to the amp via Bluetooth using my phone (Pixel 3a, Android 11) and whilst connected, can use it as a BT speaker to play music from Spotify. However, nothing I do seems to get the app to connect to the amplifier. 

-I've updated the amp to the latest firmware using my laptop/web browser. 
-I've followed all the instructions in the Bluetooth Connectivity Troubleshooter to the letter (CODE - Gateway Bluetooth Connection Troubleshooting - my.marshall.com)

No matter what I do, or what order I install/uninstall/connect, the app will not see the amplifier. Everything works otherwise - I'm able to apply Patches from ? using a USB connection - and the amp sounds great. I'd just like to be able to control it from my phone.

edited 03 Oct 2021 at 01:11 AM

Harleigh Maguire

asked 16 Sep 2021 at 03:16 AM

Harleigh Maguire
0

votes

2

answers

219

views

I have a xiaomi redmi note 8 and also have a problem connecting the marshall gateway app to the amp code50.
I can only be connected as if I were listening to music, I even tried to connect it with an otg adapter, it works like that, but there are a lot of problems with braking the application? Please if it is possible to solve this problem.

 And if I tried all variants except one, and that is to uninstall every marshall application to amplify my Marshall Code 50 Firmware 1.4.4 recognize bluetooth connection from which I can control my installed Gateway 1.5.5 of course not just music to listen to But that I have complete control and whether maybe the problem is that the usb is included in my computer, whether to turn it off because I registered everything else. If anyone can answer all these questions I will be grateful.

asked 08 May 2021 at 09:33 AM

Vladimir kovacevic
1

vote

0

answers

302

views

I have an issue with tap tempo on the Code 25 with 1.45 firmware and wondered if anyone else has the same issue.  The manual says you should "press MOD and DEL selection switches together". When I do that the amp does indeed go into tap tempo mode (tap the selector switch to set tempo), but regardless of how quick I press the buttons or if I hold down one and then hit the other it always switches on the MOD module too. The other double combination switches (tuner and bluetooth) dont do this and work as expected and only switch on those functions without switching on or off any other modules.

edited 31 Mar 2021 at 12:47 PM

Joliet Jake (61)

asked 30 Mar 2021 at 10:34 PM

Joliet Jake (61)
0

votes

1

answer

277

views

I seem to be having the same issues that a lot of people have reported, where I cannot get the Marshall Gateway app to connect to my Code 25. I've only had the amp for about a week and I cannot get the app to see it.

I can connect to the amp via Bluetooth using my phone (Pixel 3a, Android 11) and whilst connected, can use it as a BT speaker to play music from Spotify. However, nothing I do seems to get the app to connect to the amplifier.

-I've updated the amp to the latest firmware using my laptop/web browser. 
-I've followed all the instructions in the Bluetooth Connectivity Troubleshooter to the letter (CODE - Gateway Bluetooth Connection Troubleshooting - my.marshall.com)

No matter what I do, or what order I install/uninstall/connect, the app will not see the amplifier. Everything works otherwise - I'm able to apply Patches from ? using a USB connection - and the amp sounds great. I'd just like to be able to control it from my phone.

asked 28 Mar 2021 at 10:54 AM

Andrew Jarvis
0

votes

1

answer

326

views

Hi, I just recieved my Code 50 yesterday "bought brand new" and the amp sounded great until i hooked up to my pc this morning and downloaded a featured preset not a communiy preset. I am running usb not bluetooth and its my studio setup. Now all the distortion and gain sounds like the input gain is wide open clipping the signal coming in at all volume levels, and on all distortion and od gain presets. I tried to reset the amp and did a firmware update now its litterally so bad you cant play it. This is certainly a software issue cause the effects and clean tones sound fine. This happened immediatley after i sent the preset usb from the website to the amp from the pc. Also i tried several guitars, usb cables, guitar cables and even my mac. just dont know wether i should send it back or if thiscan be fixed with a firmware patch or something , Thanks

asked 09 Mar 2021 at 07:41 PM

stephen anderson
0

votes

1

answer

233

views

I have followed all the Forum and Support threads, re-installed current  Amp firmware, updated the Gateway App, restared everything several times... the iPhone does not see the Amp when blue light is flashing to 'pair'. Also not visible to ipad or other devices so I'm assuming it's a problem with the CODE system itself. I haven't even got as far as connecting the Gateway App!

Looking through the forum, this is clearly not an isolated event - looks like the Amp firmware is WAY behind current Bluetooth versions.

Any suggestions please? I am still within my return for credit timeline - should I send it back to the dealer?

asked 06 Feb 2021 at 12:12 PM

Tony Hulbert
0

votes

0

answers

247

views

Yes, I've read the many questions of the same nature on the forum, and performed all the suggested actions. None of them have been successful.  I've seen many questions similar to mine, and only a few who have been able to make it work... and of those who did, their solutions didn't work for me.

When I connect my amp to my phone's bluetooth, it will pair for audio with no problems.  I can play audio through the amp.  When I open Gateway, there is no "red button" prompting me to connect.  When I tap on the CODE tab in the menu, it says "Not connected" and when I tap on the green "Scan for apps" button, nothing happens.

It will connect to my Samsung tablet with no issues.

Here are the steps I have tried:
Factory reset on the amp.
Unpair  and forget the amp in my phone's bluetooth settings.

Uninstall the app from my phone after clearing the cache and the data.

Update the firmware on the amp (the browser window said I was up to date but I installed the latest firmware anyway.)

What else can I do?  I don't want to return the amp because it sounds great, but not having the amp controls on my phone is a deal breaker.

 

 

asked 26 Sep 2020 at 06:59 AM

Jeremy Stroop
1

vote

4

answers

503

views

I have a Marshall Code 50 running MCU version 1.44 and Gateway (Android version 1.5.5) on a Samsung Galaxy S9+ running the latest OS. I can bluetooth pair to the amp and play music, but can not connect to the amp to change my presets from the library.  I have reloaded the latest firmware on the amp, deleted and reinstalled the Gateway app, paired and unpaired several times.  Nothing seems to work.  I even grabbed my old Galaxy S7 Edge phone and that Gateway app on it does the same thing.  Does my amp need to be serviced for Bluetooth connectivity?

asked 03 Aug 2020 at 12:12 PM

Kent Knudsen (1)
0

votes

1

answer

561

views

 

Hi,

 

I have found a weird thing that may or may not be known with iOS + Bluetooth and the Code 50.

The CODE 50 when playing backing tracks / using it as a Bluetooth speaker is very quiet (So the master is wacked up and the playing guitar is extremely loud). 

 

and the weirdest thing (which physically makes sense but still it shouldn't do it) is that the Amp is predominatly a Left speaker when playing music through bluetooth as my phone (iPhone 6S) thinks my amp is bluetooth headphones rather than speaker (as the headphone icon pops up on the top right). 

 

My amp is on the latest firmware update.

 

Is there any fix for this? There's nothing in the gateway app for audio balencing

 

asked 26 Jul 2020 at 09:49 PM

Ed Thwaites
0

votes

1

answer

420

views

I can't get the phone app and code 100 amp to connect. bluetooth does connect but the app will not show or allow to connect thus make the app unsuable. i have redownload app manty time. reconnected phone many times. amp is up to date firmware. i have had the app working fine and connected in the past.but now no matter how many redownloads, resets and starting fresh i can longer connect with the app to control it. i have been through every setting and all combinations on connecting updatig reseting and nothing seems to work. need help please. thank you.

asked 11 May 2020 at 03:31 PM

shawn isaac
0

votes

1

answer

519

views

Marshall Code 25 Bluetooth not working !!!!

i try to update firmware to 1.44, i try with diferente phones, android/ios/tablet etc.... wont detect nothing.... bluetooth Marshall not appear!... 

Marshall apps is a fucking crazy bad... and support too.....

Need help please. I love my marshall code 25, but without bluetooth i send it back....

asked 28 Dec 2019 at 06:39 PM

andre Sarabando
4

votes

8

answers

1.1k

views

Hi I have a CODE 100H head/cab and a CODE 100 combo both with the latest firmware re-installed from Marshall and both have this issue, i.e. the amp very oftenn completely freezes when I save a preset.

Steps to reproduce:

- Modify any patch on the front panel

- Save

- 50% of the times the amp seems to freeze. The preset is saved but you can no longer change preset and there is no sound coming out.

The same happens if you modify a patch from the iOS app via bluetooth and then save it from there.

 

It's REALLY frustrating and I can't believe I didn't find anything on this forum under the "crash on save" keywords. Seeing it happens on both of my CODE units it much be a software bug, I don't think it has anything to do with my units.

Anyone else has seen this problem?

 

Thanks!

asked 23 Dec 2019 at 11:45 PM

Lele X (14)
0

votes

2

answers

518

views

Yesterday I bought a second handed CODE 50. There were no problems at the buyer's house, but when I tried to make a bluetooth connection at home, it failed. I restored the factory settings and updated the firmware to version 1.44. I still can't make a bluetooth connection (iPhone 6s, iPhone X, iPad, MacBook Pro, all with the most recent iOS and MacOS versions) and now also the amplifier loudly knocks every 3 sec. I tried all suggested solution, but still no bluetooth connection. And the knocking sound is really annoying! How can I solve these problems?

 

asked 14 Nov 2019 at 07:50 AM

Kai Bouwhuis
0

votes

2

answers

819

views

I have a code 50 and am trying to update firmware. I have an iPhone X with the Chrome app installed (newest version). I am logged into my Marshall and the gateway app. The gateway app shows I am connected via Bluetooth, but on the my Marshall firmware download page it says I am not connected and my browser doesn’t support download. 

It’s very frustrating, Marshall or any support appreciated.

asked 19 Sep 2019 at 04:03 AM

Mar Fede-mac
0

votes

2

answers

747

views

Just bought my Code 50 tried to connect the Gateway App to either my iPhone 7 or iPad Air 2.

Did a firmware update to 1.44 , the amp is paired in Bluetooth but when in Gateway, it just says it is connecting but never does.

I have tried reinstalling the firmware, forgetting the edvice and re-pairing, removing all other BT devices etc. etc. but still it will not connect.

UPDATE: this was an iOS issue, not the amp. The latest update to iOS beta 13.1 resolved it. 

 

edited 07 Sep 2019 at 06:17 AM

Steven Clarke

asked 31 Aug 2019 at 04:56 PM

Steven Clarke
0

votes

1

answer

722

views

The iOS Gateway app was unable to connect to my CODE 50 even though my MacBook Pro is connected via bluetooth, so I did a factory reset and then tried to do a firmware update. The first part of the firmware update (1.44) appeared to install correctly. Next I saw a DSP update and tried to apply that update. In the middle of the DSP update, I received an error message to the effect that the update failed and I should power off & on my computer/device. I powered my Mac off & on, but the CODE 50 shows a progress indicator (about 20%) and says "DO NOT SWITCH OFF."

I tried to reinstall the firmware/DSP update, but this time the update process would not even begin. I suspect the  problem is the frozen progress indicator and whatever ongoing or frozen process is causing the "DO NOT SWITCH OFF" message.

Othe than ignoring the warning on the CODE 50 and powering it off & on, I don't see what else I can do. Is there a way to abort the ongoing or frozen process without turning the CODE off.

What should I do?

edited 28 Aug 2019 at 03:47 AM

Jim Marshall (12)

asked 28 Aug 2019 at 02:06 AM

Jim Marshall (12)
0

votes

3

answers

731

views

I just bought a CODE 100 combo. Bluetooth audio is pairing just fine but the app never finds or connects to my CODE!

I tried everything, i even uninstalled the app rebooted the phone and started from scratch following your guide but still no luck.
Galaxy s9+ up to date CODE firmware 1.44 and gateway app 1.5.5

Fix this please

edited 12 Jul 2019 at 08:03 AM

Cris Lebrun

asked 11 Jul 2019 at 10:18 PM

Cris Lebrun
1

vote

1

answer

837

views

Dear Marshall Team,

It took some time, almost a year, but finally we got the long awaited update of the firmware to fix the painful Bluetooth issue on CODEs. I installed it a few days ago (which was a bit of an issue as reported in another of my posts but finally succeeded) and now CODE does what it is supposed to do.  BT comes on and connects as it should every time I turn on the amp and start Gateway on my Ipad/Iphone.

I'm very happy that you could fix the problem and I encourage all brothers and sisters in pain to upgrade the firmware asap if they haven't done already.

In the light of this fix I think we, the community, may also forgive you that for months you told us that it is not a firmware issue ;-) 

So far I also think that the BT connection is more stable than it used to be. 

Now I can enjoy again my little CODE 25. 

Thanks, Alex F.

asked 03 Jul 2019 at 08:28 AM

Alexander Fleischmann (14)
0

votes

1

answer

1.2k

views

I just got this head recently and installed the latest firmware update the other night (6/20/2019).   When I try to connect my IPad through the My Marshall app it seems to be a hit or miss proposition but more miss than hit.   In my settings on the IPad it shows me as connected, and the blue light on the head goes from flashing to solid.  On the app, it shows the head detected but when I press on that I get a "Connection Rejected"  (You may only control amps you are already connected to for audio output) and there's no control over the head from the app.   Now several other times it syncs right up.  I'm at a loss though.  Am I doing something wrong maybe in the sequence (operator error) or is there an issue somewhere else.  The manual doesn't really reference Bluetooth that well.  I'm not bluetooth savy becuase I rarely use it except for my phone in the car and connection there is automatic after I initially set it up.

So is it me?  Is it the gateway software?  Is it the head??   Help please?

asked 22 Jun 2019 at 05:32 PM

Kim Lubstorf
Showing results 1 to 20 of 69
Loading - please wait...