Questions
Showing results 1 to 11 of 11
0

votes

1

answer

208

views

Hello everyone, I wanted to tell you about my situation and if you can provide me with any advice or help. 

I have about 4 months ago my Marshall CODE 25 because I liked its characteristics and its comfortably to play in home.
but now I tried to connect it with my pc to use it as an interface and I couldn't, becouse it dosen't appaers in my daw.
When I put the usb cable, the guitar did not sound in the amp and I assumed that because the sound would go to my pc,
but when I took it out, my guitar did not sound,
it does not pick up my guitar.
I tried his bluethooth function and my amp plays the sound of my phone.

Maybe conect the cable usb make some mistake in the software, i don't
now
I've tried turning it on and off several times and resetting the amp. Please I would appreciate
a lot if you could give me any helpful information as I tried my best to have it and i worked hard to have
that amp.

asked 06 May 2021 at 05:44 AM

Vicente Farias
0

votes

1

answer

335

views

Hi all,

Happy New Year! 

I have recently switched from a MacBook to a Windows 10 desktop and had previously recorded via USB straight into Garageband using the CODE with no issues at all. After switching to Windows 10 I can't get the CODE to connect though, it wont recognise in Chrome to manage the presets (I just get the "CODE: Not Connected" message in the bottom left of the screen, I have tried free trial versions and free to use DAW's and none of them see the CODE as an input. I've installed the ASIO4ALL driver but still no joy, the CODE is on the 1.44 firmware.

Am I missing something or is there a setting to change other than switching the MIDI input to ASIO?

Thanks in advance,

Rob

asked 03 Jan 2021 at 11:27 AM

Rob Furminger
1

vote

2

answers

466

views

Hi,
owned a code 25 for a while now but only really started using it during lockdown but have to say I'm really impressed. I'm just using it for living room playing and connected to my DAW as a way of laying down ideas but seriously, it's REALLY good.

For context, I've played guitar for 27 years and working in live music has been my primary source of income (pre lockdown....) for around 17 years. I'm usually a live-sound engineer and tour manager and occasionally fill in the gaps with some guitar-teching. I'm uk-based but have international clients, mostly guitar-based, playing mostly academy sized venues but have done major festivals worldwide and one short stint of an arena tour. The point here is not to blow my whistle, simply to say I've spent a lot of time being exposed to all manner of amps and modelling.

I own a line 6 helix and while the CODE isn't as flexible with regards to I/O, I genuinely feel like it's amp-modelling, especially for crunch, fuzzy or blown out tones, blows the Helix out of the water. Not that I'm as likely to use metal tones or had much cause to tweak them but I've noticed those kind of presets can sound a little thin. Also, higher gain sounds in general could benefit from a graphic EQ somewhere in the modelling chain, as it can be prone to squeak at frequencies usually outside of a regular amps range, presumably because of the full-range nature of the cab.

So, my query is, is there any chance that the CODE range is likely to get any substantial firmware updates or maybe 2nd generation hardware that could bring additional functionality/Pro level durability and a decent footswitch... I'm impressed that you've managed to get that much functionality out of a mono-jack but a few extra switches or even just midi connectivity for use with after market footswitched to access would open the amp right up.

Personally, I'd love to see one capable of more complex I/O routing i.e. the ability to record your dry input to DAW over usb and similarly, route from the DAW to the amp input for re-amping.

Midi I/O and an xlr input with phantom and a decent sounding pre would make it a nice little hub for a solo recording setup.

Anyway, great work Marshall/Softube, really hope you develop the line further.


asked 27 Oct 2020 at 02:41 PM

Jamie-Lee Warlow (1)
1

vote

0

answers

613

views

Hi. I have a question: The Code USB interface is ok only with pc or it work with really usb midi? With usb midi pedal like Midi commander by Meloaudio, for explample, work or not?

if it work only with pc like daw is very very poor choise. next firmware? the orignal PDL 91009 is ok, but it's very very limited.

thx 

paolo

asked 19 Nov 2019 at 05:32 PM

Paolo Goi (1)
0

votes

0

answers

526

views

I have a CODE 100h + CODE412 and I love them !!!!
I use a pedal board with different effects and was thinking of adding a looper / switcher (Boss ES-5 or MUSICOM LAB EFX LE).
I would like to know if with the looper I have listed I can change presets to CODE100H via midi. Do I need a USB / MIDI interface? Thanks

asked 18 Nov 2019 at 05:01 PM

Ziggy 75 (10)
0

votes

2

answers

997

views

I just got around to updating the firm ware on the code 100 thought as long as i had the amp connected to my pc via the usb cable I would check out the code editor and it would not respond looked at the manual casually and did not notice any mention of how to connect

 

dos this need to be acomplished using a midi to usb cable

asked 18 Jun 2019 at 01:46 PM

Stephen Rosin (1)
0

votes

0

answers

1k

views

Hello, I would like to connect one of my PCs (OS linux) on a Marshall CODE 50 and take control via usb midi.

When I open /etc/dmmidi2 in read acces. Reading file char by char, I see information when I touch the buttons of the amp (PREFX, AMP, MOD, ...). I can find the information in CODE-Midi-Implementation-Chart-V2.1.pdf.

I usually get two or three bytes and cross it with the document.
But this frame is not in the form Start of Transmission> Header> Command> End of Transmission.

By against when I open /etc/dmmmidi2 in write access, I can not send any command.
After having turned on the amp, I sent the following sequence for RECALL PRESETS 05:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x73 0x01 0x05 0xF7
or RECALL CURRENT SETTINGS:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x72 0x01 0x00 0xF7
Start of Transmission> Header> Command> End of Transmission
This command does not seem to work. Is there an intermediary step?

Would it be possible to give me a typical sequence to the CODE or a document that will explain the procedure to operate (ON / OFF) one of the button (PREFX, AMP, MOD, ...) of the amp.
Thank you in advance.
Cordially.

yoann

asked 11 May 2018 at 07:24 AM

Yoann Thomas
0

votes

4

answers

3k

views

Hey all - new to the forums, new to Marshall amps and had a few questions about the Code 50 I just ordered that will be here in a day or so.  I have played my guitars through my buddy's Code 50 and am familiar with editing the patches, tweaking the tones and getting the sounds that I want from the amp to fit my playing style.  What I am not familiar with is the use of footswitch and any Midi capabilities it may have.

1) Can one use just a regular on/off type of old school footswitch to turn an effect or amp on/off or initiate a patch change?  I have several old school footswitches I have successfully used on many different amps, albeit older amps, and it has always worked.  Curious since the Marshall footswitch actually holds presets if anything like that would work.

2) As far as Midi goes, I come from a Line6 multi-effects world and know that many of their multi-effect units have the capability to control effects on/off/parameters and patch/bank switching via Midi commands.  Does the Code software have anything like that if hooked up to a PC/Mac running a DAW that has the capability to send midi control commands to change patches/effects realtime during recording/playback.

Thanks for any input and excited to get this amp.  I am a player of over 30 years and have only ever played through Crate amps for the past 20+ years that have finally given up and the cost to repair is more than new.  Bash Crate all you want but they were loud and proud and with the right EQ/effects loops made some damn good musical sounds.

asked 20 Mar 2018 at 03:04 AM

Billy Nab
0

votes

2

answers

3k

views

How do I set up my new CODE50 USB to my CUBASE9? "CODE" shows up in CUBASE Inspector for MIDI Tracks, but no signal.

Do I need a CODE driver? 

Does the CODE50 USB only send MIDI?

Does it send audio waveform signals?

I viewed a couple of Marshall video tutorials that didn't help and it says practically nothing in the download manual. 

Thanks, Kevin

asked 23 Feb 2018 at 12:31 AM

kevin hughes
0

votes

1

answer

2.5k

views

I just want to check with fellow CODE users if they are facing the same issues that I am dealing with.

Biggest (and most annoying) issue is, it's a matter of luck connecting the CODE through USB. 2 times out of 10 my pc recognizes the amp the first time I plug it in. Mostly it gives an error that device is not connected properly or not recognized by windows. So I end up unplugging and plugging again until (if ever) it's been recognized. (Using windows 8.1 btw) Then suddenly in the middle of a recording session my DAW starts to drag like if I am running on a PC Pentium 600.  (It's running on a 3000$ alienware) This is a sign that somehow CODE get disconnected itself.  Now you have only option left: Restart the PC and start all over again.

 So far I have checked with different USB cables, and I am using the shortest ones as possible as I can. (less than 80 cm.) I can't check with another pc since I don't have another one, but I am running Yamaha THR-10 smoothly, without any problems at all!

So I don't believe that there's an issue with my pc. And speaking of THR, why the hell CODE doesn't have it's dedicated USB drivers. I am kind of sure that the issue I am facing is all about the ASIO drivers that we are left with as an only option.

 Second issue is, maybe only 1 out of 20 times I am able to get any presets from web site. Even if it looks like CODE is connected in the Device Manager, and the Chrome (or Opera) says MIDI is connected, I can't send any presets to the amp. After a few tries, this ends up with web browsers got frozen and only option is again: restart your pc!

I really would like to hear from people who are facing similar issues and how they could get over with it. (if they ever could)

And hopefully the only answer I receive from Marshall team is not going to be: "Thanks for your feedback, we will pass this to our technical team"

 Regards,

edited 07 Jun 2017 at 07:36 PM

Gurhan Ozkaya (1)

asked 06 Jun 2017 at 07:57 PM

Gurhan Ozkaya (1)
0

votes

2

answers

2.3k

views

Is there a capability to control the Code 25 via USB MIDI???

 

Thanks in advance...

asked 16 Nov 2016 at 01:46 AM

Joe Ruggiero
Showing results 1 to 11 of 11
Loading - please wait...