Questions
Showing results 1 to 20 of 136
0

votes

1

answer

34

views

Hello y'all,

I've been having a problem with JVM 205Combo.
During corona-lockdown, when we were not allowed to rehearse with the band, I had took my amp home with me....
As I'm always curious to find other sounds, I started experimenting with connecting other speaker cabs to my JVM. But, as I later discovered, the cable I used was no good and I think I blew up the main amplifier. I looked for the fuse, for it seemed logical to me that the fuse was blown, but couldn't find it. I also have a JCM 800 2205 head, a JMP MK2 2204 head and I've been having a JCM900 4100 head in the past. Now, all these amps were fused, so if anything went wrong, it was just the fuse that was blown. In fact, I've experienced that!
But no fuse on the JVM....is that correct? Because if it is, my problem is bigger than I thought. In that case, what was blown instead? The output transformer? My tubes?

I hope somebody can help me out on this one. And I promise never to experiment with other speakers or whatsoever.

Thnx anyway!
Cheers!

 

asked 10 Sep 2021 at 08:23 PM

Arno Visser
0

votes

1

answer

61

views

Hello,    New amp I procured and I am hoping to get some Q's answered regarding. 

It did not come with a footswitch and being new to all of this I do not know why I need one or which footswitch to get ????

Also, I was told by the original owner that it is quite than it used to be and may need a new tube.   Also do not know which way to go with this ...   

 

Last point is when switching over from clean to overdrive it is buzzing and I am not sure why...

 

After hours on youtube and reading the instruction manual I am even more confused. 

 

Thanks in advance for comments/advice. 

 

Wade

asked 25 Aug 2021 at 11:03 PM

Wade Gail
0

votes

1

answer

58

views

I ordered a DSL40CR in January and it was amazing but in April it just stopped working. Sent it back to get fixed but it was deemed beyond repair and they sent a brand new one and it arrived in June. After a few weeks the new amps' volume would fluctuate after maybe 3-4 hours of playing. Got in touch with the shop I bought it from and described the problem, they said it was most likely the tubes so they sent two new ones. After replacing both tubes the volume still fluctuates after it's been played for a few hours.

asked 24 Aug 2021 at 10:15 PM

Lewis McLean
0

votes

0

answers

81

views

Can I use Tung Sol EL34B tubes in my Origin 20H amplifier to replace the stock EL34 tubes ?

asked 08 Jul 2021 at 03:38 PM

RAYMOND N
0

votes

1

answer

99

views

first time poster, long time tech. having experience with marshall amps I am familiar with issues stemming from problematic circuit boards (i.e.-DSL/TSL etc ) however my experience regarding this model is limited. can't say I have ever been a fan of DSP. for me ,as a player/tech DSP is a deal breaker. like the dreaded nintendo game format red circle of death, once the DSP bites it you're done.  I just seek a simple answer for my customer who bought one second hand,never re-tubed. amp lost power.sounds like a badly blown speaker (speakers test good). replaced output tubes and driver tube (original outputs tested badly). preamp tubes test good. supply voltages appear to be normal.overdrive channel LED switches from red to amber to slightly different amber but no green.  clean channel button switches normal. red-orange-green.master volume button doesn't come on.sometimes if you perform factory reset all buttons function but sound is still terrible. nice clean signal going thru to pin 7 of V7.  in between V7 and phase inverter something is haywire. my money is on the DSP board but not having a flow chart ??? tried to get a signal straight into the power amp but got nothing out. any input appreciated guys.  one thing more...i get the 2 separate heater voltages. V6 is 12vdc but the other for the remaining tubes originating at the tranny, is that standard 6.3 ? didn't see it on the schematic.

 

 

 

edited 29 Jun 2021 at 12:17 PM

gordon perry

asked 29 Jun 2021 at 12:16 PM

gordon perry
0

votes

2

answers

123

views

So, my Marshall JVM 410c lately started making minor crackling sounds before creating a huge pop sound, and the level would be reduced until I changed the channel. This was concerning enough, and I had intended to have it checked out at my local shop, but then it began to hum and then produced the same pop sound last night. Even when I change the channel, no sound comes out now. Is there anyone who knows what's causing this? I'm not familiar with tube amplifiers, so I'm assuming this just means I need to replace a tube rather than the entire unit.

? ? ?

edited 14 Jun 2021 at 07:52 AM

rony yadav

asked 25 May 2021 at 06:44 AM

rony yadav
0

votes

0

answers

161

views

I read the post about the TSL 602 BIAS at this forum link:

?

should I change the two standard EL34s, and mount EL34EHs, the BIAS value is always 80mV for this model even when changing tube brands, or is this value valid only by replacing the two EL34s with the same brand?

Thank's

asked 14 Apr 2021 at 10:33 PM

Gerardo Manganiello
0

votes

1

answer

171

views

Ok.  A couple questions I'm sure can be answered here.

I just bought the DSL40CR less than a week ago.  It's awesome for something smaller.  Great at home amp.

However, the first clean channel is very low on volume, while if i switch to the other clean its 3 times as loud or more.  Is something wrong here?  One clean channel  can be cranked to max volume which would be the equivalent of the other clean channel at maybe a 2.

Second question, I'm hearing a lot of talk of people swapping out the speakers in these amps.  Is this always recommended?

Third question, I desire more reverb.  Is getting a pedal the answer, or another Marshall amp altogether?  Would a JVM be any better in the reverb category?

Fourth question, would getting different tubes change any of the previous concerns?  Would getting different tubes make the amp better?

Im new to valve amps, and I'm struggling to answer all these questions.

 

Thanks

 

 

asked 22 Mar 2021 at 11:55 PM

Robert Kortekamp
0

votes

1

answer

166

views

I've got an Origin 5C, about 6 months old.  Has worked fine and is a fun little amp.  But last night I had my first issue.
Got the rig set up, with front-end fx, and also some fx in the loop. Warmed it up, then played a few bars in low power. All worked fine, so I switched to full power, and stepped away for a few minutes to let it warm up some more.
When I came back, it was still powered on (light and mild hum), but the footswitch was dead and there was zero volume. Not even cable crackle when plugging and unplugging the guitar.
I messed around with all the connections. Pulled everything and plugged in directly (also checked the instrument cable). So, guitar > cable > amp. Still no volume, and just a slight hum (very slight; it wasn't ampliyfing anything, so this was just circuit hum).
I dissambled the the thing, to check tubes and connections. Everything looked grand.
Reassembled it, and it worked fine. Played for a good 10 or 15 minutes at medium volume, and it was a charm.
But then the volume started dropping. Would come in and out. Then it dropped completely, and the footswitch went dark again.
I tried connecting an external preamp into the return (with a dummy plug in the send), but no luck. Footswitch was still dark.
Hum but no volume.
Haven't tried it yet today, but I'm expecting the same behaviour. My assumption is that there is something that goes sideways when the temperature gets up.
So, two questions:
1 - Is this a power tube issue? I haven't noticed any other problems or symptoms of bad tubes. And, like I said, it's 6 months old. Never gigged, but played loud fairly often.
2 - What's up with the footswitch? I can't find any schematics of the Origin series, and I don't care to go tracing. So, I'm not sure exactly where the FS fits into the circuit. I was wondering if that symptom might help to diagnose.
Anyway, a great little amp, but it's acting up!
Has anybody had or heard of this issue?
Thanks, friends

asked 17 Mar 2021 at 01:12 PM

Clark Powers
0

votes

1

answer

202

views

I have a Marshall Origin 50H, its about 7 months old and I've used it perhaps  maybe 10 times total for some pretty low volume playing and never used on anything but the lowest 5w setting. I'm using it with a proper 16 ohm Celestion cabinet and proper cables and playing for about 40yrs so know what I'm doing, well, most days that is lol! :)

Anywho,  after about 10 minutes the volume drops WAY off and I'm assuming its a power tube since the level of gain doesn't change at all,  just the volume and it gets real compressed. 

Since I've only had the amp 7 months, would the tubes be covered under warranty in any way? I would hope so due to how little I've used it, thanks for any insight.

edited 02 Mar 2021 at 11:34 PM

Steven I

asked 02 Mar 2021 at 11:24 PM

Steven I
0

votes

1

answer

145

views

Hello, 

I recently found a JCM900 4500 series hi-gain dual reverb in mint condition. The serial is Y38091---I know that it was made in 1990, I was just curious past the "Y" what the remaining five digits might pertain to? I was really just intrigued by reading the history of these and was wondering if mine is one of the first few produced and if it would be possible to find out what tubes and components were used on this one. Also, is it possible to get a copy of the original manual? 

 

Thanks for any and all help! I love my 900.

asked 18 Feb 2021 at 04:24 PM

adam capps
1

vote

1

answer

208

views

hi , can I swap out the ecc83 preamp tube in V1 for a ecc81 in a SC20H? I’m just trying to lower gain to a much cleaner sound - preferably to the origin clean . 

Any suggestions - outside of “ buy an Origin “ ;) 

thanks 

 

p.s REISSUE THE JMD:1 heads !

asked 18 Feb 2021 at 08:11 AM

Johnathan McLam (1)
1

vote

1

answer

239

views

Hi. I'm having a problem with my DSL5CR. When plugged direct into the amp and switched to the Classic gain channel it works perfectly. However, when switched to the Ultra gain channel, the guitar is very faint and what can be heard is a weak-fuzzy sound. When I first noticed the problem, I thought it was a case of the tubes needing to warm up, as after 30 seconds the level would gradually increase, unfortunately the problem has got worse. Could it be the pre-amp tubes at fault? 

Thanks,
Steve

asked 12 Feb 2021 at 08:08 PM

Steven Fallon (1)
0

votes

2

answers

607

views

Are there instructions on how to bias Origin 50 power tubes? A schematic?

asked 20 Jan 2021 at 02:07 PM

Kevin Alspaugh
0

votes

0

answers

192

views

I have a DSL40C i purchased in September. After a few weeks it started to emmit an arcing sound when in standby. I returned it to the supplier who found nothing wrong. It has been ok since except for a  wooshing sound when it is first turned on that stays at the same volume even if I turn the volume up but slowly dissapears over time (I assumed this was just the valves heating up and settling and happened in both normal and low power modes) Today it started the arcing again and it would not turn the volume off in standby mode, then standby mode started working correctly and now if i put the amp in low power mode the volume starts decreasing and eventually disappears after about 10 seconds. Normal power mode seems to be OK though. Does this point to defective tubes already?

asked 17 Jan 2021 at 10:57 PM

Peter Brown
0

votes

1

answer

216

views

I purchased a new DSL40CR  a few months ago. I think I need to replace some of the tubes/valves. The product is still under original manufacturer warranty, so I would like to take it to someone qualified to work on Marhsall amps, rather than change them myself. I have never owned a brand new amp before, so I don't want to void any warranty. How can I locate a proper amp technician in my area (Buffalo, NY) to help me with this? Appreciate any help. Thanks .

Dave

asked 21 Dec 2020 at 07:17 PM

David Marcoux
0

votes

0

answers

213

views

Hello,

can I use my JTM60 speaker with a Marshall Origin 20H Head?

Also, my JTM60 has suffered some damage when my nephew tried to power on the amplifier, she cranked everything up but didn't succed, when I got home I didn't noticed it was all cranked up and powered it, it blew tubes and some more, I had it repaired but it didn't get back to the same sound as before... I'd like to have it checked by qualified personnel, can you indicate someone in Italy, please?

Thanks a lot,

Marco

asked 21 Dec 2020 at 02:25 PM

Marco Damian
0

votes

2

answers

280

views

Got myself what i thought could be the greatest idea of an amp,Origin 20h.  looks awesome , plenty of clean , Too much clean , i can t seem to get gain and dirt out of it , i tried with Humbuckers seymour"s Pearly gates, and Aph-1 ( little gain but just to mention )  and with my strat with ssl-1 and ssl-5 it was cleaner than my fender Blues junior  ??  is there a way i can get it to growl more , change tubes? what should i put in  to get it the meanest ? i reallythought i could drive it better , oh yes and the treble, mid , bass, no big difference there also .  Not sure i want to invest to much in case there is no significative results.  what should i do to get real gainy dirt, please don t answer me to by a jcm900. cheers

asked 12 Nov 2020 at 04:12 AM

Rick Goy
0

votes

1

answer

445

views

Somewhere on the internet it was mentioned that replacing the power tube of a DSL5CR does not require to re-bias as the DSL5CR is a "self bias" system.
Can anyone confirm this?

Other question what would be the best brand to have for my DSL5CR power tube?

asked 05 Nov 2020 at 10:33 AM

Fred Lucas
0

votes

1

answer

397

views

Hi all, i’m looking to buy a new marshall sc20c jcm800 tube amp and get payday loans 24/7 and it doesn’t have a headphone jack . Could i plug headphones into the jack called “DI OUT” or not and what does this do?

edited 11 Nov 2020 at 03:19 PM

Jack Evans

asked 28 Oct 2020 at 04:43 PM

Jack Evans
Showing results 1 to 20 of 136
Loading - please wait...