I have an issue with tap tempo on the Code 25 with 1.45 firmware and wondered if anyone else has the same issue. The manual says you should "press MOD and DEL selection switches together". When I do that the amp does indeed go into tap tempo mode (tap the selector switch to set tempo), but regardless of how quick I press the buttons or if I hold down one and then hit the other it always switches on the MOD module too. The other double combination switches (tuner and bluetooth) dont do this and work as expected and only switch on those functions without switching on or off any other modules.
I have tried everything to do the firmware update on my new Code 25. Its showing v1.11 still.
I have tried Crome, Edge, and downloading the manual windows exe. I have updated drivers, booted amp in "safe mode" (which identified usb as READY but still wonnect connect in My.Marshall
Please help! I love the amp but need to be able to update the firmware
I just got this head recently and installed the latest firmware update the other night (6/20/2019). When I try to connect my IPad through the My Marshall app it seems to be a hit or miss proposition but more miss than hit. In my settings on the IPad it shows me as connected, and the blue light on the head goes from flashing to solid. On the app, it shows the head detected but when I press on that I get a "Connection Rejected" (You may only control amps you are already connected to for audio output) and there's no control over the head from the app. Now several other times it syncs right up. I'm at a loss though. Am I doing something wrong maybe in the sequence (operator error) or is there an issue somewhere else. The manual doesn't really reference Bluetooth that well. I'm not bluetooth savy becuase I rarely use it except for my phone in the car and connection there is automatic after I initially set it up.
So is it me? Is it the gateway software? Is it the head?? Help please?
Please read this post in the spirit in which it is posted.
I monitor these forums regularly as I have five Marshall CODE amps. and I guess I like to see what's going on and stay up-to-date. And I suppose I enjoy sharing my knowledge and helping others where I can. I must also note that I've not had any of the issues described on these forums with any of my CODE amps. And I must also note that I think they're the best modelling amps. around i.e. they're Marshalls and enough said.
But what concerns me (and hence this post) is this: there really does seem to be a lack of interest on the part of Marshall Amplification when it comes to the CODE range (at least here on the forums i.e. if emailing Technical Support yields different results then I do apologise) (and given the fact that I've had no issues at all with any of my CODE amps., as noted above, I've never had to contact Technical Support so I would not know). It's almost as if Marshall regret the day they got into this modelling business (and if that's not the case: sorry but that's my personal impression at the moment after, what, around eighteen months or so of monitoring these forums???). I mean to say: there are so many posts around here (dating back) asking for feedback re: apparent bluetooth issues, projected dates for new firmware updates, etc. etc. etc. And no answers. There's even been one or two posts asking if Marshall is going to continue with the CODE range or if it's something they want to get away from. No answer. I think you get the picture.
The above being said: I do understand how frustrating it must be to be asked the same old questions over and over and over again ESPECIALLY when a forum member couldn't even be bothered to search the forums for an answer before posting and asking a question or before reading the manual. Hell: if I had a few USD or GBP or EUR for every time I've answered a question on here re: standalone software to control these amps. well, then, I'd probably buy some more CODE amps.!!! LOL!!! Point is and all jokes aside: I do get it. But it's no excuse for a lack of response on some very key issues (like those mentioned above). And what's more: for some they're not asking for favors i.e. they're quite willing to help themselves but need a little bit of input (the Master Volume issue comes to mind here) and they just don't get that input. And (back to the firmware issue): some are even prepared to roll back their firmware to a previous version as (apparently) some issues were not issues in previous versions i.e. they're not even insisting that a new, immediate, firmware update with fixes is made available. Fairer than that I don't think they could be. But: no response (or, in some cases, a very non-committal response anyway).
In closing: I don't know if I'm correct in my assumption that Marshall isn't too interested in this CODE range of amps. I also don't know if, maybe, this (perceived on my part anyway) lack of interest is because this particular market is quite tough nowadays (what with other modelling amps. and a plethora of plugins and the rest of the junk out there) and maybe the core business (the more expensive and professional products) is being conentrated on and these CODE amps. are just an irritation. But you need to know this (as I have noted already): they are STILL Marshall amplifiers. And there is nothing on the market (whether it be another modelling amp. or a plugin) that sounds like these amps. (or, at very least, comes as close to emulating the more expensive and professional Marshall valve amps.). So they are actually something to be proud of Marshall. Just bear this in mind going forward.
As I said: please read in the spirit in which this is being posted.
No response is necessary either. But please do take cognisance of what I've posted above going forward.
On my Code-25 I had a setting I liked to use - preset 7 - Volcano, but now it's different (maybe changed after a firmware update?)
Does anyone know what the manual settings are to emulate Volcano (previous pre-set 7)?
After some more hunting and pecking, I discoved how to get the listings to appear in My Gateway. I had to make sure my phone was connected to my computer then went through MENU on the Gateway phone app. After logging in, the app hilighted SYNC and once pressed away it went. I then managed to sort accordingly and save. The app does what it is supposed to do so now I have no problems at this point. Again, why isn't this explained in a document or tutorial...? Programmers and suppliers cannot expect users to understand their thought process without some clue here or there.