Hello when I attempt to connect my Code 25 for a firmware update the device is not recognized. It says USB malfunction. I read a post that says I must use a midi compatible cable. Is there a particular way to identify if the cable is compatible or not. If I search the cables I find do not seem to have the proper connector. Thanks
owned a code 25 for a while now but only really started using it during lockdown but have to say I'm really impressed. I'm just using it for living room playing and connected to my DAW as a way of laying down ideas but seriously, it's REALLY good.
For context, I've played guitar for 27 years and working in live music has been my primary source of income (pre lockdown....) for around 17 years. I'm usually a live-sound engineer and tour manager and occasionally fill in the gaps with some guitar-teching. I'm uk-based but have international clients, mostly guitar-based, playing mostly academy sized venues but have done major festivals worldwide and one short stint of an arena tour. The point here is not to blow my whistle, simply to say I've spent a lot of time being exposed to all manner of amps and modelling.
I own a line 6 helix and while the CODE isn't as flexible with regards to I/O, I genuinely feel like it's amp-modelling, especially for crunch, fuzzy or blown out tones, blows the Helix out of the water. Not that I'm as likely to use metal tones or had much cause to tweak them but I've noticed those kind of presets can sound a little thin. Also, higher gain sounds in general could benefit from a graphic EQ somewhere in the modelling chain, as it can be prone to squeak at frequencies usually outside of a regular amps range, presumably because of the full-range nature of the cab.
So, my query is, is there any chance that the CODE range is likely to get any substantial firmware updates or maybe 2nd generation hardware that could bring additional functionality/Pro level durability and a decent footswitch... I'm impressed that you've managed to get that much functionality out of a mono-jack but a few extra switches or even just midi connectivity for use with after market footswitched to access would open the amp right up.
Personally, I'd love to see one capable of more complex I/O routing i.e. the ability to record your dry input to DAW over usb and similarly, route from the DAW to the amp input for re-amping.
Midi I/O and an xlr input with phantom and a decent sounding pre would make it a nice little hub for a solo recording setup.
Anyway, great work Marshall/Softube, really hope you develop the line further.
Hi. I have a question: The Code USB interface is ok only with pc or it work with really usb midi? With usb midi pedal like Midi commander by Meloaudio, for explample, work or not?
if it work only with pc like daw is very very poor choise. next firmware? the orignal PDL 91009 is ok, but it's very very limited.
Ok i havent used my code for a while and decided to get it out and dust it off for a jam... I thought it most likely needed a firmware update so decided to plug it in to my pc. Ihad been through this process when i bought it so i didnt anticipate any problems LOL
So firstly it wouldnt detect the amp even though pc audio was being routed through it, anyhow got through the teething issues and enabled the midi thing as per instructions and then bam! amp went past the connected but and it showed the available firmware it was on 1.3 and showed 2 further updates to the current 1.4.
I started it and nothing happened. sat watching the dots fly by and absolutely nothing was going on. So after what seemed like hours i decided to cancel and try again and it would sometimes detect it, sometimes not sometimes stard to update, sometimes not and then i tried the last time and it all seemed to go well, i actually saw % numbers going up and then it stalled again and nothing happened. I left it for a good 45 minutes and still nothing, so i decided to cancel it again and try one last time.
only now the amp says the firmware version is 0.0 and it wont do anything. I am unable to factory reset even. It really should not be this difficult to update the damn firmware. I have been trying to do this for HOURS!
My CODE 25 connects to my PC via both through MIDI in Chrome and through the Firmware Update Utility but it refuses to do anything but sit there while the gold loading circle just spins and spins. I've left it for upwards of 30 minutes. I'm unable to click on check for updates or anything. Tried rebooting a few times, tried turning blutooth off while doing it, etc. My amps current version according to both the amp and the app is v1.3. Any suggestion on what to try? Should I do some kind of factory reset to the amp and try again? Any help or suggestions would be appreciated.
As a side note, I'm also unable to "download preset to amp" to test it out even though it's giving me the go ahead to do it on the preset site. I'm sure the issue is connected to being unable to update the firmware.
I`m trying to use my BOSS Gt-100 as a Midi controller to change channels on my JHS410H.
It works...but sometimes amplifier doesn`t change a channel.
Looks that it`s amp fault, because gt100 sends PC messages on each press.
I think that JVM gets sometimes confused because all messages out of GT100 comes in formula: 2xCC+1xPC.
Could you advice how to deal with it? Is there any option to change a firmware on JVM midi module to make communication more realiable?
firstly, i am disappointed with the code. this amp seems like its still at test phase, its to buggy for a release. would expect marshall to only release a new product unless its 100% reliable.
connecting ios devices to code is always problematic. very unstable.
my main problem now is updating firmware. cant update in chrome. i have midi capability approved for marshall but keep getting midid disabled error even though i clearly have midi enabled.
tried opera, and the midi is working and the code is coming up as connected. i get as far as a message stating that firmware is updating with a status bar and percentage marker. doesnt update! stays at 0% and never moves. left it overnight and still 0% when i woke.
i have spent more time messing about with the problems with this amp than playing guitar. do i need to sell this and just buy a guitar interface? maybe
also, when using this amp through garageband there is no dedicated clean preset to use with garageband or other AU. basically it goes into garageband with a marshall preset and then the other AU preset is on top of the marshall preset. ideally this amp should include a straight clean unprocessed preset to work with other software AU's. i really do think people need to consider a good quality guitar interface before purchasing this amp. its very restricitve and unreliable. if you are not gigginG i dont see the point in this amp.
CAN SOMEONE HELP ME WITH THE FIRMWARE ISSUE ASAP!