Happy New Year!
I have recently switched from a MacBook to a Windows 10 desktop and had previously recorded via USB straight into Garageband using the CODE with no issues at all. After switching to Windows 10 I can't get the CODE to connect though, it wont recognise in Chrome to manage the presets (I just get the "CODE: Not Connected" message in the bottom left of the screen, I have tried free trial versions and free to use DAW's and none of them see the CODE as an input. I've installed the ASIO4ALL driver but still no joy, the CODE is on the 1.44 firmware.
Am I missing something or is there a setting to change other than switching the MIDI input to ASIO?
Thanks in advance,
owned a code 25 for a while now but only really started using it during lockdown but have to say I'm really impressed. I'm just using it for living room playing and connected to my DAW as a way of laying down ideas but seriously, it's REALLY good.
For context, I've played guitar for 27 years and working in live music has been my primary source of income (pre lockdown....) for around 17 years. I'm usually a live-sound engineer and tour manager and occasionally fill in the gaps with some guitar-teching. I'm uk-based but have international clients, mostly guitar-based, playing mostly academy sized venues but have done major festivals worldwide and one short stint of an arena tour. The point here is not to blow my whistle, simply to say I've spent a lot of time being exposed to all manner of amps and modelling.
I own a line 6 helix and while the CODE isn't as flexible with regards to I/O, I genuinely feel like it's amp-modelling, especially for crunch, fuzzy or blown out tones, blows the Helix out of the water. Not that I'm as likely to use metal tones or had much cause to tweak them but I've noticed those kind of presets can sound a little thin. Also, higher gain sounds in general could benefit from a graphic EQ somewhere in the modelling chain, as it can be prone to squeak at frequencies usually outside of a regular amps range, presumably because of the full-range nature of the cab.
So, my query is, is there any chance that the CODE range is likely to get any substantial firmware updates or maybe 2nd generation hardware that could bring additional functionality/Pro level durability and a decent footswitch... I'm impressed that you've managed to get that much functionality out of a mono-jack but a few extra switches or even just midi connectivity for use with after market footswitched to access would open the amp right up.
Personally, I'd love to see one capable of more complex I/O routing i.e. the ability to record your dry input to DAW over usb and similarly, route from the DAW to the amp input for re-amping.
Midi I/O and an xlr input with phantom and a decent sounding pre would make it a nice little hub for a solo recording setup.
Anyway, great work Marshall/Softube, really hope you develop the line further.
Hi Guys and Gals.. and the Marshall team....
I recently a Marshall CODE 25 amp and it is working fine except for one thing it says " MIDI is not available" is coming up so I cant listen to a another user preset.
Any Fixes out there? my browser is google chrome and it is up to date.. Thanks Ben
I write small desktop app for CODE25.
Everything working except uploading whole preset into CODE.
This is sysex message which i sending into Amplifier to change active preset
sysex data=(0,33,21,127,127,127,114,2,0,68,101,97,116,104,32,83,121,109,98,111,108,105,99,32,50,32,32,0,75,55,20,40,50,1,1,0,25,50,25,1,12,30,0,0,50,50,0,50,0,0,0,0,50,50,50,1,2,35,25,30,20,1,0,75,75,1,7,1,2,3,4) time=0
what is wrong ?
I have a CODE 100h + CODE412 and I love them !!!!
I use a pedal board with different effects and was thinking of adding a looper / switcher (Boss ES-5 or MUSICOM LAB EFX LE).
I would like to know if with the looper I have listed I can change presets to CODE100H via midi. Do I need a USB / MIDI interface? Thanks
I ve got a helix hx I am trying to use for channel swap on the amp.
For all of the above the following applies:
- JVM footcontroller is disconnection
- JVM midi has been reset: its on MIDI channel 1
Boss ES5 (works)
I can get it working using a Boss ES5: https://www.youtube.com/watch?v=3YI65cgA4XI
Midi cable setup: Boss ES5 (out) > JVM (IN)
Also going from Boss through the helix (midi passthrough works).
Midi cable connection: Boss ES 5 (out) > Helix (IN) > Helix (out) > JVM
However, this is using Midi patch panel change. Not sure how this differs from MIDI CC?
Helix HX (not working)
For Helix im following this video : https://youtu.be/simaPS7dzLw?t=55
Midi cable connection: Helix (out) > JVM
Im using MIDI CC and following the table in JSH User manual.
channel : 1
Function: CC: 16
= clean channel, Orange mode.
I set the amp up so that the midi controller is BLINKING and it doesnt stop blinking: its not receiving the signal?
I feel like Im close to getting there.
My CODE 25 connects to my PC via both through MIDI in Chrome and through the Firmware Update Utility but it refuses to do anything but sit there while the gold loading circle just spins and spins. I've left it for upwards of 30 minutes. I'm unable to click on check for updates or anything. Tried rebooting a few times, tried turning blutooth off while doing it, etc. My amps current version according to both the amp and the app is v1.3. Any suggestion on what to try? Should I do some kind of factory reset to the amp and try again? Any help or suggestions would be appreciated.
As a side note, I'm also unable to "download preset to amp" to test it out even though it's giving me the go ahead to do it on the preset site. I'm sure the issue is connected to being unable to update the firmware.
I have an iPhone with google chrome installed but when I try to get a preset it says midi not available everything else on Bluetooth is working. Are you telling me I have to have a desk top instead of using my iPhone to directly get presets? So confusing!!
So, for the first time, I wanted to download a preset or “patch” off of the my.marshall site from another fellow Marshall lover. I clicked on the preset link from YOUTUBE, which took me to the Marshall user on MY MARSHALL. I utilized my iPhone so the default browser is SAFARI of course. I read that My.Marshall does not work with SAFARI so I downloaded CHROME to my iPhone which is version 71.0. When I went back to My. Marshall to save the preset to my Library I STILL got the MIDI IS NOT AVAILABLE notice on the bottom of my screen. I powered down my phone to restart thinking maybe I had to allow the Newly downloaded CHROME to “re-set” but still same thing MIDI IS NOT AVAILABLE. PLEASE ADVISE as this is SO FRUSTRATING!!!!! Thank you in advance....
hi, i wonder if there is away to dwonload presets through tablet or smart phone to the amp in wierless way ?
or the only way is to use pc midi ?
Hello, I would like to connect one of my PCs (OS linux) on a Marshall CODE 50 and take control via usb midi.
When I open /etc/dmmidi2 in read acces. Reading file char by char, I see information when I touch the buttons of the amp (PREFX, AMP, MOD, ...). I can find the information in CODE-Midi-Implementation-Chart-V2.1.pdf.
I usually get two or three bytes and cross it with the document.
But this frame is not in the form Start of Transmission> Header> Command> End of Transmission.
By against when I open /etc/dmmmidi2 in write access, I can not send any command.
After having turned on the amp, I sent the following sequence for RECALL PRESETS 05:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x73 0x01 0x05 0xF7
or RECALL CURRENT SETTINGS:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x72 0x01 0x00 0xF7
Start of Transmission> Header> Command> End of Transmission
This command does not seem to work. Is there an intermediary step?
Would it be possible to give me a typical sequence to the CODE or a document that will explain the procedure to operate (ON / OFF) one of the button (PREFX, AMP, MOD, ...) of the amp.
Thank you in advance.
i switch through my presets with the Marshall PEDL-91009, however, this pedalboard only has 3 switches and a bank switch, however i would like to have a pedalboard with more than 3 preset switch button for faster recall ... is there a solution (maybe via MIDI) , or a compatible footswitch that i am unaware of?
Hey all - new to the forums, new to Marshall amps and had a few questions about the Code 50 I just ordered that will be here in a day or so. I have played my guitars through my buddy's Code 50 and am familiar with editing the patches, tweaking the tones and getting the sounds that I want from the amp to fit my playing style. What I am not familiar with is the use of footswitch and any Midi capabilities it may have.
1) Can one use just a regular on/off type of old school footswitch to turn an effect or amp on/off or initiate a patch change? I have several old school footswitches I have successfully used on many different amps, albeit older amps, and it has always worked. Curious since the Marshall footswitch actually holds presets if anything like that would work.
2) As far as Midi goes, I come from a Line6 multi-effects world and know that many of their multi-effect units have the capability to control effects on/off/parameters and patch/bank switching via Midi commands. Does the Code software have anything like that if hooked up to a PC/Mac running a DAW that has the capability to send midi control commands to change patches/effects realtime during recording/playback.
Thanks for any input and excited to get this amp. I am a player of over 30 years and have only ever played through Crate amps for the past 20+ years that have finally given up and the cost to repair is more than new. Bash Crate all you want but they were loud and proud and with the right EQ/effects loops made some damn good musical sounds.
I have a problem with connecting a TC Electronics G-System to my JVM 410HJS. The way described in the manual does not work. Preset switching is not possible. The Midi channels have been matched to Ch 1 according to the manual but programming is not working. The JVM doesn't receive messages (no fast blinking). Does the G-System not send useable midi data at all?
Thank you in advance!
con i use the boss fc200 as a footswitch with the code50 amp. Im having a midi connector set to the plug where it is to be connected.
if so what standard midi presets do i need in order to be able to switch form setting 02 to e.g. 53
Hello everyone. I would like to know if an update for the code was envisaged. if yes, marshall, can you accelerate the time of change of preset in midi .. it's so slow! we have the break of the preset change. it's too bad. thank you
firstly, i am disappointed with the code. this amp seems like its still at test phase, its to buggy for a release. would expect marshall to only release a new product unless its 100% reliable.
connecting ios devices to code is always problematic. very unstable.
my main problem now is updating firmware. cant update in chrome. i have midi capability approved for marshall but keep getting midid disabled error even though i clearly have midi enabled.
tried opera, and the midi is working and the code is coming up as connected. i get as far as a message stating that firmware is updating with a status bar and percentage marker. doesnt update! stays at 0% and never moves. left it overnight and still 0% when i woke.
i have spent more time messing about with the problems with this amp than playing guitar. do i need to sell this and just buy a guitar interface? maybe
also, when using this amp through garageband there is no dedicated clean preset to use with garageband or other AU. basically it goes into garageband with a marshall preset and then the other AU preset is on top of the marshall preset. ideally this amp should include a straight clean unprocessed preset to work with other software AU's. i really do think people need to consider a good quality guitar interface before purchasing this amp. its very restricitve and unreliable. if you are not gigginG i dont see the point in this amp.
CAN SOMEONE HELP ME WITH THE FIRMWARE ISSUE ASAP!
I just want to check with fellow CODE users if they are facing the same issues that I am dealing with.
Biggest (and most annoying) issue is, it's a matter of luck connecting the CODE through USB. 2 times out of 10 my pc recognizes the amp the first time I plug it in. Mostly it gives an error that device is not connected properly or not recognized by windows. So I end up unplugging and plugging again until (if ever) it's been recognized. (Using windows 8.1 btw) Then suddenly in the middle of a recording session my DAW starts to drag like if I am running on a PC Pentium 600. (It's running on a 3000$ alienware) This is a sign that somehow CODE get disconnected itself. Now you have only option left: Restart the PC and start all over again.
So far I have checked with different USB cables, and I am using the shortest ones as possible as I can. (less than 80 cm.) I can't check with another pc since I don't have another one, but I am running Yamaha THR-10 smoothly, without any problems at all!
So I don't believe that there's an issue with my pc. And speaking of THR, why the hell CODE doesn't have it's dedicated USB drivers. I am kind of sure that the issue I am facing is all about the ASIO drivers that we are left with as an only option.
Second issue is, maybe only 1 out of 20 times I am able to get any presets from web site. Even if it looks like CODE is connected in the Device Manager, and the Chrome (or Opera) says MIDI is connected, I can't send any presets to the amp. After a few tries, this ends up with web browsers got frozen and only option is again: restart your pc!
I really would like to hear from people who are facing similar issues and how they could get over with it. (if they ever could)
And hopefully the only answer I receive from Marshall team is not going to be: "Thanks for your feedback, we will pass this to our technical team"