Questions
Showing results 1 to 9 of 9
0

votes

2

answers

48

views

Hi all,

I write small desktop app for CODE25.

Everything working except uploading whole preset into CODE.

This is sysex message which i sending into Amplifier to change active preset

sysex data=(0,33,21,127,127,127,114,2,0,68,101,97,116,104,32,83,121,109,98,111,108,105,99,32,50,32,32,0,75,55,20,40,50,1,1,0,25,50,25,1,12,30,0,0,50,50,0,50,0,0,0,0,50,50,50,1,2,35,25,30,20,1,0,75,75,1,7,1,2,3,4) time=0

what is wrong ?

thanks.

CODE Gateway Presets MIDI

asked 30 Nov 2019 at 12:35 PM

matthew black
0

votes

0

answers

42

views

I have a CODE 100h + CODE412 and I love them !!!!
I use a pedal board with different effects and was thinking of adding a looper / switcher (Boss ES-5 or MUSICOM LAB EFX LE).
I would like to know if with the looper I have listed I can change presets to CODE100H via midi. Do I need a USB / MIDI interface? Thanks

CODE Presets USB MIDI

asked 18 Nov 2019 at 05:01 PM

Ziggy 75
0

votes

1

answer

203

views

My CODE 25 connects to my PC via both through MIDI in Chrome and through the Firmware Update Utility but it refuses to do anything but sit there while the gold loading circle just spins and spins. I've left it for upwards of 30 minutes. I'm unable to click on check for updates or anything. Tried rebooting a few times, tried turning blutooth off while doing it, etc. My amps current version according to both the amp and the app is v1.3. Any suggestion on what to try? Should I do some kind of factory reset to the amp and try again?  Any help or suggestions would be appreciated.

As a side note, I'm also unable to "download preset to amp" to test it out even though it's giving me the go ahead to do it on the preset site. I'm sure the issue is connected to being unable to update the firmware.

Thanks!

CODE Gateway Presets Firmware MIDI

asked 21 Mar 2019 at 04:15 PM

Brett Ewaschuk
0

votes

0

answers

287

views

Hello, I would like to connect one of my PCs (OS linux) on a Marshall CODE 50 and take control via usb midi.

When I open /etc/dmmidi2 in read acces. Reading file char by char, I see information when I touch the buttons of the amp (PREFX, AMP, MOD, ...). I can find the information in CODE-Midi-Implementation-Chart-V2.1.pdf.

I usually get two or three bytes and cross it with the document.
But this frame is not in the form Start of Transmission> Header> Command> End of Transmission.

By against when I open /etc/dmmmidi2 in write access, I can not send any command.
After having turned on the amp, I sent the following sequence for RECALL PRESETS 05:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x73 0x01 0x05 0xF7
or RECALL CURRENT SETTINGS:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x72 0x01 0x00 0xF7
Start of Transmission> Header> Command> End of Transmission
This command does not seem to work. Is there an intermediary step?

Would it be possible to give me a typical sequence to the CODE or a document that will explain the procedure to operate (ON / OFF) one of the button (PREFX, AMP, MOD, ...) of the amp.
Thank you in advance.
Cordially.

yoann

CODE Presets USB MIDI

asked 11 May 2018 at 07:24 AM

Yoann Thomas
0

votes

1

answer

863

views

Hello, 

i switch through my presets with  the Marshall PEDL-91009, however, this pedalboard only has 3 switches and a bank switch, however i would like to have a pedalboard with more than 3 preset switch button for faster recall ... is there a solution (maybe via MIDI) , or a compatible footswitch that i am unaware of? 

CODE Presets Footswitch MIDI

asked 21 Mar 2018 at 04:47 PM

Daniele Varra
0

votes

4

answers

1.4k

views

Hey all - new to the forums, new to Marshall amps and had a few questions about the Code 50 I just ordered that will be here in a day or so.  I have played my guitars through my buddy's Code 50 and am familiar with editing the patches, tweaking the tones and getting the sounds that I want from the amp to fit my playing style.  What I am not familiar with is the use of footswitch and any Midi capabilities it may have.

1) Can one use just a regular on/off type of old school footswitch to turn an effect or amp on/off or initiate a patch change?  I have several old school footswitches I have successfully used on many different amps, albeit older amps, and it has always worked.  Curious since the Marshall footswitch actually holds presets if anything like that would work.

2) As far as Midi goes, I come from a Line6 multi-effects world and know that many of their multi-effect units have the capability to control effects on/off/parameters and patch/bank switching via Midi commands.  Does the Code software have anything like that if hooked up to a PC/Mac running a DAW that has the capability to send midi control commands to change patches/effects realtime during recording/playback.

Thanks for any input and excited to get this amp.  I am a player of over 30 years and have only ever played through Crate amps for the past 20+ years that have finally given up and the cost to repair is more than new.  Bash Crate all you want but they were loud and proud and with the right EQ/effects loops made some damn good musical sounds.

CODE Presets USB Footswitch MIDI

asked 20 Mar 2018 at 03:04 AM

Billy Nab
0

votes

1

answer

334

views

Hello everyone. I would like to know if an update for the code was envisaged. if yes, marshall, can you accelerate the time of change of preset in midi .. it's so slow! we have the break of the preset change. it's too bad. thank you

CODE Presets MIDI

asked 14 Jan 2018 at 03:58 AM

Thierry Tant
1

vote

9

answers

520

views

hi

firstly, i am disappointed with the code.  this amp seems like its still at test phase, its to buggy for a release.  would expect marshall to only release a new product unless its 100% reliable.

connecting ios devices to code is always problematic. very unstable.

my main problem now is updating firmware.  cant update in chrome. i have midi capability approved for marshall but keep getting midid disabled error even though i clearly have midi enabled.

tried opera, and the midi is working and the code is coming up as connected. i get as far as a message stating that firmware is updating with a status bar and percentage marker. doesnt update! stays at 0% and never moves. left it overnight and still 0% when i woke.

i have spent more time messing about with the problems with this amp than playing guitar. do i need to sell this and just buy a guitar interface? maybe

also, when using this amp through garageband there is no dedicated clean preset to use with garageband or other AU. basically it goes into garageband with a marshall preset and then the other AU preset is on top of the marshall preset. ideally this amp should include a straight clean unprocessed preset to work with other software AU's.  i really do think people need to consider a good quality guitar interface before purchasing this amp. its very restricitve and unreliable. if you are not gigginG i dont see the point in this amp. 

CAN SOMEONE HELP ME WITH THE FIRMWARE ISSUE ASAP!

CODE Bluetooth iOS Presets Firmware MIDI

asked 15 Nov 2017 at 09:40 AM

ste cullen (5)
0

votes

1

answer

1.3k

views

I just want to check with fellow CODE users if they are facing the same issues that I am dealing with.

Biggest (and most annoying) issue is, it's a matter of luck connecting the CODE through USB. 2 times out of 10 my pc recognizes the amp the first time I plug it in. Mostly it gives an error that device is not connected properly or not recognized by windows. So I end up unplugging and plugging again until (if ever) it's been recognized. (Using windows 8.1 btw) Then suddenly in the middle of a recording session my DAW starts to drag like if I am running on a PC Pentium 600.  (It's running on a 3000$ alienware) This is a sign that somehow CODE get disconnected itself.  Now you have only option left: Restart the PC and start all over again.

 So far I have checked with different USB cables, and I am using the shortest ones as possible as I can. (less than 80 cm.) I can't check with another pc since I don't have another one, but I am running Yamaha THR-10 smoothly, without any problems at all!

So I don't believe that there's an issue with my pc. And speaking of THR, why the hell CODE doesn't have it's dedicated USB drivers. I am kind of sure that the issue I am facing is all about the ASIO drivers that we are left with as an only option.

 Second issue is, maybe only 1 out of 20 times I am able to get any presets from web site. Even if it looks like CODE is connected in the Device Manager, and the Chrome (or Opera) says MIDI is connected, I can't send any presets to the amp. After a few tries, this ends up with web browsers got frozen and only option is again: restart your pc!

I really would like to hear from people who are facing similar issues and how they could get over with it. (if they ever could)

And hopefully the only answer I receive from Marshall team is not going to be: "Thanks for your feedback, we will pass this to our technical team"

 Regards,

CODE Presets Windows USB MIDI recording PC Driver

edited 07 Jun 2017 at 07:36 PM

Gurhan Ozkaya (1)

asked 06 Jun 2017 at 07:57 PM

Gurhan Ozkaya (1)
Showing results 1 to 9 of 9
Loading - please wait...