How do I set my Code 100 up to record on windows and what is a user friendly software to use.
Thanks a mil!
I've got a (not very big) problem with recordnig music via USB. I use only clean sound, typical settings for my guitar equipped with 2x Wilkinson WVC humbuckers are:
preamp - DSL, gain - 2.0 (increasing gain over 2.5 makes sound NOT as clean, as I want it to be), volume - 10, B/M/T - 7/10/5, noise gate - 0.5
power amp - American, presence - 2, resonance - 6
I tried Audacity and Presonus Studio One, and in both cases recording level is about -20dB. Of course I can normalize volume in post processing to let's say -3dB and I still have quite satisfactory quality, but I loose this 17dB of signal/noise ratio.
Any suggestion how to increase USB output level?
I just want to check with fellow CODE users if they are facing the same issues that I am dealing with.
Biggest (and most annoying) issue is, it's a matter of luck connecting the CODE through USB. 2 times out of 10 my pc recognizes the amp the first time I plug it in. Mostly it gives an error that device is not connected properly or not recognized by windows. So I end up unplugging and plugging again until (if ever) it's been recognized. (Using windows 8.1 btw) Then suddenly in the middle of a recording session my DAW starts to drag like if I am running on a PC Pentium 600. (It's running on a 3000$ alienware) This is a sign that somehow CODE get disconnected itself. Now you have only option left: Restart the PC and start all over again.
So far I have checked with different USB cables, and I am using the shortest ones as possible as I can. (less than 80 cm.) I can't check with another pc since I don't have another one, but I am running Yamaha THR-10 smoothly, without any problems at all!
So I don't believe that there's an issue with my pc. And speaking of THR, why the hell CODE doesn't have it's dedicated USB drivers. I am kind of sure that the issue I am facing is all about the ASIO drivers that we are left with as an only option.
Second issue is, maybe only 1 out of 20 times I am able to get any presets from web site. Even if it looks like CODE is connected in the Device Manager, and the Chrome (or Opera) says MIDI is connected, I can't send any presets to the amp. After a few tries, this ends up with web browsers got frozen and only option is again: restart your pc!
I really would like to hear from people who are facing similar issues and how they could get over with it. (if they ever could)
And hopefully the only answer I receive from Marshall team is not going to be: "Thanks for your feedback, we will pass this to our technical team"
Promises, promises ... "we'll fix it soon"; " bluetooth issues will be addressed in future firmware updates"; " USB recording issues will be looked into"; AND, a 2-way footswitch will be available for Code 25/50 users when Code 100 is released. Am I alone in my disappointment for Marshall's seemingly apathetic (non) responses to purchasers of their "not ready for prime time" digital products?!?!?! I really wanted a Marshall Amp after 45 years as a Fender user. My mistake. I should have known better. Useless, unsupported, glitched, buggy, unreliable, etc., etc., etc. What say you Marshall in an attempt to save any reputation you thought you had?!?!?!?
Hi, Although My laptop recognizes My code 50 via usb, nuendo 4.3 doesn't (although it recognizes My zoom and korg asio).
Therefore, I'm unable to assign the code has an input for recording via usb. Thanks.
I've been recording on garageband and other softwares for a long time already!
However, I've bought this (crappy) amp to record via USB on these DVAs I'm used to work with. SO, aparently, after questioning people who uses the same amp, and here on the forum, NOBODY could explain the real reason why this "amp" won't work for recording via usb!
The TWO computers I use (macbook and PC - windows7) reconize the amp, however NO SOUND AT ALL are recorded!
I am familiar with LINE 6 products and I use them a lot. No problem at all with this gear! But MARSHALL, the most famous brand of amps on the world, releases an amp promising to do something they aparently are not able to!
Lame amp! recently bought and, hopefully, recently SOLD! Waste of my time and money!
I recently found out that my code 25 doesn't have a output that supports a jack. I've used a "Gibson Memory cable" before, and that was ok for my use. So my question is; which program should use when I connect my code amp to my computer? I'm not looking for an expensive and supergood program, just a program that works for my hobby playing :-) I hope this was understandable :-)
I was using the usb connection to record on Audacity. The guitar I was using was a Fender Strat with noiseless pups. I found that the signal stregth was really low and the only way I could get a decent recorded signal was to turn up the master volume to an unbearable level and was close to getting a stern talking to from my better half. I then tried the same process but used some headphones and this sorted the level issue so it recorded a strong signal. There was still a bit of crackle on the recording but much improved from the last firmware release.
I then recorded some acoustic guitar without headphones. This was a martin DRs1 with a stock fishman pup. Signal strength was really good and the quality was great. No hum or hiss or crackle.
Great to hear others experiences.