Questions
Showing results 1 to 20 of 33
0

votes

0

answers

8

views

While attempting to set up the footswitch (more help needed there), I somehow duplicated 01 So American over 92 19x12 and it is gone.  I liked both of them and have been unable to get back 02, even with factory reset of the amp and footswitch.

Any thoughts would be appreciated!

Presets Footswitch

asked 26 Jul 2020 at 10:33 PM

Kevin Kruszenski
0

votes

2

answers

134

views

Hi!

Can you advise please ? How can I configure two presets/chanels for one knob in the footswitches? I need to switch two presets with oneknob?

  for example : Rhythm guitar to solo (different chanel with the addition of an effect through FX Loop) and back to the Rhythm  mode?  

Presets Footswitch jvm410h

asked 17 Feb 2020 at 12:05 PM

Marat Sadvakassov
0

votes

1

answer

187

views

Hi

I recently bought a Marshcall Code 50 and I have two old footswitches (a Behringer and a Boss Dual foot switch FS-6). All I want to be able to do is cycle between presets on the code. On both the footswitches the code only cycles backwards, and not forwards at all. Is there a setting on the code somewhere that I need to change so that I can cycle either way through the presets?

Much appreciated

CODE Presets Footswitch

asked 25 Jan 2020 at 03:54 PM

Renier Pienaar
0

votes

0

answers

144

views

Is there any option to change volume with the PEDL 90008 ?

I know that it is possible to change volume by editing different presets. 

But I want to know if there is a way to change the volume with other methods.

Would be great if there were an FX  to change volume in switch mode.

 

Presets Footswitch

asked 13 Nov 2019 at 04:33 PM

Wolles Berserk
0

votes

0

answers

198

views

I was wondering if the creator of the KASHMIR preset would be interested in also creating the FLANGER part for KASHMIR using all the current preset settings (amp, cabinet, speaker etc) as a complimentary preset for the turnaround section of the song.  I believe, from forums, that a preset will switch better (Marshall CODE footswitch) if the preset has the same amp, speaker and or cabinet setting as it takes away the millisecond delay of switching between amps in a particular preset.  Look forward to your answer and or creation of said beasty.

Regards Kev

 

CODE Presets Speaker Cabinet Footswitch

asked 30 Jul 2019 at 02:07 AM

Kev Lawlor
0

votes

1

answer

305

views

Can I save downloaded user presets to my footswitch and how???

Using the Code 50

CODE Gateway Presets Footswitch

asked 04 Jul 2019 at 08:40 PM

joe wheeler
0

votes

0

answers

278

views

Hi, I havent had any problems with my 2 Code100h that i run in stereo in my marshall 1960v cabs, in any way until now, besides the usual dirty pots.  I am trying to save the "in amp" tuner as a patch or an effect on a patch as the instructional video states. I do have the upgraded footswitch.  The only way ive found to acceas the tuner by footpedal is by turning one of the switch mode choices into the tuner, which makes every single patch have the tuner as the switch mode option. Kinda defeats the purpose. Is there any way to set the tuner as a patch by itself or as a switch mode option on just 1 patch and not all of them? 

Presets Footswitch

asked 07 Apr 2019 at 02:44 PM

William Burleson
0

votes

1

answer

325

views

I'm noticing a significant volume difference between the presets I have programmed on the footswitch in A2 & A3, is there a way to adjust this so the volume remains the same when switching between A2 & A3 ? 

CODE Presets Footswitch

asked 05 Apr 2019 at 04:52 PM

Ron DeMartino
0

votes

1

answer

530

views

Hi please refer to this previous question to help explain the background to my question:  https://my.marshall.com/forum/question/1479/marshall-code-100---should-it-have-come-with-a-2-way-foot-switch?filterType=recent&myActivity=True

Basically I bought a Marshall code 100 (no it's not 100H or 100C just a plain 100). It was out of its box and on display but discounted by about $180 because it had a slight dent in the base. The store rep claimed it had not been used. I bought it due to the price but after a few months I realised it should have come with a 2 button footswitch. I then raised this fact with the store and they agreed to supply me with the one that should have come with it. It has been about 6 months since they promised me they would replace and every time I ring up they come up with some bullshit excuse like "oh our suppliers on the other side of the country claim it is not sold as a spare and they have to order it in and they are not receiving any new stock of this item until Feb". 

So Feb has come and gone so I am about to ring them and vent my frustrations on them. Then I thought maybe I could get the PEDL 91009 foot switch instead of the PEDL-91010, at a discounted price (perhaps to the value of the cheaper switch that should have come with it), as I am told it is much better.  As I have never had or even used a foot switch and am completely clueless on them I have a few questions:

Does the basic PEDL-91010 footswitch only allow you to switch to the next preset up or down on the preset list of 100 presets? Or can you jump from like preset number 4 to preset number 98? If it only allows you to switch to the next one up or down does the 91009 model allow you to switch between any two presets on my list? Does the 91009 model allow you to program more than 2 presets to switch between when playing a song? 

Finally, one responder to my other post mentioned that the Code 100 only comes with a basic 2 way footswitch and that the PEDL 91010 is an optional extra. But this contradicts what others were saying (eg that it is the PEDL 91010 footswitch that it comes with).

Anyway I am confused and need all this cleared up so I am fully armed when I next call the store.

CODE Presets Footswitch

asked 10 Mar 2019 at 02:04 PM

julien casella (1)
0

votes

1

answer

239

views

So about a year ago I got a footswitch for my Code 50, and when i first got it, it started banking backwards on it's own. I was able to stop it...until now. The worst part of it, is when i go to use the amp's tuner, it immediately exits because it thinks the button is being pressed. When it began a few days ago, I was able to press the bank button to increase the bank and counteract the issue, but now the bank button stopped working. Maybe I pressed it too hard or too much or something. I cant remember how I fixed it last time or whether or not the bank button worked, but all I know is this time it might be done for good. If anyone knows of this issue or has had it happen to themselves, please let me know how I can fix it. I dont remember all the presets that were saved to it, but I can remember a couple. Please help!!!

CODE Presets Footswitch

asked 08 Mar 2019 at 07:57 PM

Keenan Borgerson (2)
0

votes

2

answers

395

views

Hello, I got a code head and also the programable foot controller that I havent connected yet. My question is about the 30 programable presets. does this mean I can have total 130 presets or 70 factory presets and 30 custom presets.

CODE Presets Footswitch

asked 06 Feb 2019 at 04:45 PM

Robin Morgan
0

votes

3

answers

1.1k

views

I have a Code 100 and want to be able to add auto wah on top of a preset with another (Overdrive) pre-fx set and use the (4 way) footswitch to switch it in and out - can this be done ?

 

CODE Presets Footswitch

edited 03 Sep 2018 at 01:00 PM

Mike Palmer

asked 03 Sep 2018 at 12:58 PM

Mike Palmer
0

votes

0

answers

321

views

Hi guys i have a Code 50 Amp and footswitch. i have recently started to having a problem. when i am on a patch and hold in the Selector on the Switch for instance if i am in Bank B3 and hold down the B3 switch, you enter a mode which you switch off FX, Delay and reverb. i have notiched that when i go into any bank like that and want to go back out to choose another patch my amp buttons and knobs & footswitch is non responsive and i have to switch the amp on and off for it to respond again, this is very anyoing. any feedback on what the problem might be

CODE Presets Footswitch

asked 30 Jul 2018 at 01:18 PM

Dominique van der Westhuizen (1)
0

votes

1

answer

345

views

I was dicking about with tones, as you do, and when I meant to save my custom tone to my footswitch, and accidentally saved DSL Clean Chorus to #11 on the amp, Some Dely For You Too. This preset just happened to be one of my favorites. Is there anything I can do about it?

CODE Presets Footswitch DSL CODE100 Delay i am big dumb

edited 28 Jul 2018 at 08:56 PM

Riley Helton

asked 28 Jul 2018 at 08:55 PM

Riley Helton
0

votes

1

answer

438

views

I was dicking about with tones, as you do, and when I meant to save my custom tone to my footswitch, and accidentally saved DSL Clean Chorus to #11 on the amp, Some Dely For You Too. This preset just happened to be one of my favorites. Is there anything I can do about it?

CODE Presets Footswitch DSL Delay

asked 28 Jul 2018 at 08:55 PM

Riley Helton
0

votes

2

answers

735

views

I recently purchased a new code 100 which was a display model. They didn't have the box for it or the owner's manual. I subsequently downloaded the manual off the internet. On one of the pages concerning the front panel functions it talks about the F/C jack socket and mentions "connect the supplied 2-way footswitch" but I never got one with  it. Has anyone recently purchased this model and did it come with a 2 way footswitch  for scrolling through presets? If so I will try and get one off the shop for free. If they argue their way out of it are they expensive to buy separately? **Update to this is that the manual I have downloaded has code 100 and code 100h on the cover so maybe the footswitch comes only with the 100h?

 

CODE Presets Footswitch Manual

edited 17 Jun 2018 at 01:25 PM

julien casella (1)

asked 17 Jun 2018 at 12:26 PM

julien casella (1)
0

votes

1

answer

435

views

I recently added the tuner to my footswitch (preset), but now I want to undo it. I'd rather have the first bank available for a pre fx- preset. Doe anybody know how to undo it, ig by resetting the footswitch to factory settings?

thanks

Presets Footswitch

asked 25 Apr 2018 at 05:11 PM

bart kruiver
0

votes

1

answer

676

views

Hello,

How can I program my code 50 so I can switch up/down through all my 100 presets?

I am using a 2 button footswich. Connected to a code 100H it worked fine.

 

 

 

CODE Presets Footswitch

asked 17 Apr 2018 at 05:23 PM

Jimmy Digrasso
0

votes

2

answers

731

views

Hello, I need advice. How and where do I register Amplifier Code 100?  You can register footswitch PEDL 91009, PEDL-10025 GV-2 Guv'nor plus, PEDL-10026 BB2 Bluesbreaker, Headphones MONITOR ?  I live in the Czech Republic, where I bought the goods in e-shop muziker.cz.

Amplifier in combination with PEDL 91009 is really supreme . I have a month and I play all the time, much better than FENDER.

For my use bad Windows software. I'm using CODE Patch Editor, there's a lot of options and there's nothing extra. Is there any other code software? Where I can edit and create new presets, play Backing Tracks. Similar Fender FUSE. I would like to buy it :-)                                                        

Thank you in advance for your answer.

Regards, Michal :-)
                                                                                                                                           

                                                      !!!!!!! MARSHALL FOREVER!!!!!!!!

CODE Registration Presets Footswitch Software

edited 24 Mar 2018 at 05:52 AM

Michal Šušlík

asked 24 Mar 2018 at 05:35 AM

Michal Šušlík
0

votes

2

answers

1.4k

views

Hello, 

i switch through my presets with  the Marshall PEDL-91009, however, this pedalboard only has 3 switches and a bank switch, however i would like to have a pedalboard with more than 3 preset switch button for faster recall ... is there a solution (maybe via MIDI) , or a compatible footswitch that i am unaware of? 

CODE Presets Footswitch MIDI

asked 21 Mar 2018 at 04:47 PM

Daniele Varra
Showing results 1 to 20 of 33
Loading - please wait...