Questions
Showing results 1 to 8 of 8
0

votes

0

answers

45

views

hi all,

I ve got a helix hx I am trying to use for channel swap on the amp.

 

For all of the above the following applies:

- JVM footcontroller is disconnection

- JVM midi has been reset: its on MIDI channel 1

 

Boss ES5 (works)

I can get it working using a Boss ES5: https://www.youtube.com/watch?v=3YI65cgA4XI

Midi cable setup: Boss ES5 (out)  > JVM (IN)

 Also going from Boss through the helix (midi passthrough works).

Midi cable connection:  Boss ES 5 (out) > Helix (IN) > Helix (out) > JVM

However, this is using Midi patch panel change. Not sure how this differs from MIDI CC?

 

Helix HX (not working)

For Helix im following this video : https://youtu.be/simaPS7dzLw?t=55

Midi cable connection:   Helix (out) > JVM

Im using MIDI CC and following the table in JSH User manual.

channel : 1

Function: CC: 16

value 2

= clean channel, Orange mode.

 

I set the amp up so that the midi controller is BLINKING and it doesnt stop blinking: its not receiving the signal?

I feel like Im close to getting there.

 

Any ideas?

Thanks,

Eric

Presets Manual MIDI

asked 28 Jul 2019 at 09:07 AM

eric barlier
0

votes

1

answer

161

views

When I try to save a preset to the amp, there is no problem. When I try to save a preset to my library I get the message: Patch cannot be saved; sync with Marshall server in progress.  My gateway has both a Bluetooth and an internet connection. Logged into my.marshall but nothing happening. Sync button is disabled. I feel like I'm missing something in my understanding of this aspect of the Code/Gateway system. Is there a user manual for the Gateway app?

Gateway Bluetooth Presets Manual

asked 12 Jan 2019 at 02:16 AM

David Miller
0

votes

1

answer

231

views

I've read the manual and apparently the volume knob controls the volume of whatever preset is selected.

I'm running a Marshall code 50 with boss gt1 pedalboard so my question is, if i want to my sound to be controlled via pedalboard shouldn't I be able to turn volume knob all the way down and only control the amps volume with master volume knob? Because the moment i turn the volume knob down i dont hear anything.

I'm just trying to get a more deeper sound, the sound i get is just way too bright

CODE Presets Manual

asked 29 Dec 2018 at 08:02 PM

Brandon Parish
0

votes

2

answers

444

views

I recently purchased a new code 100 which was a display model. They didn't have the box for it or the owner's manual. I subsequently downloaded the manual off the internet. On one of the pages concerning the front panel functions it talks about the F/C jack socket and mentions "connect the supplied 2-way footswitch" but I never got one with  it. Has anyone recently purchased this model and did it come with a 2 way footswitch  for scrolling through presets? If so I will try and get one off the shop for free. If they argue their way out of it are they expensive to buy separately? **Update to this is that the manual I have downloaded has code 100 and code 100h on the cover so maybe the footswitch comes only with the 100h?

 

CODE Presets Footswitch Manual

edited 17 Jun 2018 at 01:25 PM

julien casella (1)

asked 17 Jun 2018 at 12:26 PM

julien casella (1)
0

votes

1

answer

306

views

On my Code-25 I had a setting I liked to use - preset 7 - Volcano, but now it's different (maybe changed after a firmware update?)

Does anyone know what the manual settings are to emulate Volcano (previous pre-set 7)?

Presets Manual Firmware

asked 28 Mar 2018 at 03:27 AM

Hershey Bell
0

votes

4

answers

668

views

Hello,

I have a problem with connecting a TC Electronics G-System to my JVM 410HJS. The way described in the manual does not work. Preset switching is not possible. The Midi channels have been matched to Ch 1 according to the manual but programming is not working. The JVM doesn't receive messages (no fast blinking). Does the G-System not send useable midi data at all?

Thank you in advance!

Guido

Presets Manual MIDI G-System

asked 18 Feb 2018 at 08:12 PM

Guido Focke
3

votes

0

answers

315

views

After some more hunting and pecking, I discoved how to get the listings to appear in My Gateway. I had to make sure my phone was connected to my computer then went through MENU on the Gateway phone app. After logging in, the app hilighted SYNC and once pressed away it went. I then managed to sort accordingly and save. The app does what it is supposed to do so now I have no problems at this point. Again, why isn't this explained in a document or tutorial...? Programmers and suppliers cannot expect users to understand their thought process without some clue here or there.

Regards.

 

Gateway Presets Manual Firmware

edited 25 Nov 2017 at 10:00 PM

Dave Duncan (56)

asked 25 Nov 2017 at 09:16 PM

Dave Duncan (56)
0

votes

1

answer

255

views

Which knob values are stored when in preset store mode. I cannot get any knobs only buttons to retain value following the programming instructions. Pedal malfunctioning? Any other tips outside what the manual has to offer?

Presets Manual

asked 25 Nov 2017 at 12:43 PM

Ken Putz
Showing results 1 to 8 of 8
Loading - please wait...