So I have had a new CODE25 for about four months, and two weeks ago it suddently started to go silent after playing a few minutes. No sound at all, very suddenly. Lights all still on, screen on (though maybe dimmed), and it won't recover until I power it down and restart--and then it may or may not play for a few minutes more after that. Didn't seem like an overheating issue (I rarely play that loud, and at the time I was using a sweet clean preset).
I've updated the firmware and still have the problem. I'm in Hawaii, and I'm not sure there's a Marshall warranty place here to do any work on it. Am I stuck returning it? Is this a common problem?
I absolutely love this thing, I'd hate to have to abandon it for poor dependability reasons.
There a many questions on this forum about the irritating noise with Code 25 and Code 50. However, it happens via the speaker only, not via the headphone connection. The presets sounds very nice in that situation. Can you explain?
Because of the noise issue I just use the Natural sound and add FX pedal effects. No noise at all. But that is not the way I want to use the Code 25. I want to use the presets.
A couple questions. I am trying to love this amp--it is compact, seems to have plenty of control, and I like how easily it connects to my computer. The problem I have is similar to others: I do not need a ton of volume and a lot of the sounds seem a bit muddy. I've tried turning the preset volume way down and use Master and this works to an extent.
1) I noticed people talking about putting a Celestion G10 Greenback in it. I'm planning on trying this. I was going to go with 8ohm to save some volume but will the frequency range be a problem? It seems like stock is a full range generic speaker likely so it can be more neutral for amp modeling and for music playback. I do not need to play music through it..... and
2) How bad will this mess up the presets? Am I basically throwing presets out if I change the speaker?
3) Has anyone modified the back of the amp to open it up? I heard some asking about this and not sure if it is worth it.
Thanks, looks like others have been curious but have not heard anyone report in on actually doing this. Love some feedback!!
I was wondering if the creator of the KASHMIR preset would be interested in also creating the FLANGER part for KASHMIR using all the current preset settings (amp, cabinet, speaker etc) as a complimentary preset for the turnaround section of the song. I believe, from forums, that a preset will switch better (Marshall CODE footswitch) if the preset has the same amp, speaker and or cabinet setting as it takes away the millisecond delay of switching between amps in a particular preset. Look forward to your answer and or creation of said beasty.
Yesterday I received my Code 50 amp. I played some hours with it and there is 1 thing that i noticed. I play most of the time at home through a headphone because neighbours, and the presets aswell as some own created sets sound really muffed if I add any Cab. I tried diffent Cabs but for me it sounds way clearer without a cab model. I was wondering how this is possible? Did i miss something? When I remove the cab from a preset add lower the presence by 2 it sounds so much better
And when playing through the speaker while gigging with friends, will this difference still be there or is a cab model "necessary" when playing through the speaker?
Hello. I find out what the body of the combo is cracking and not the speaker itself at a volume of 20% or more. This defect is even on the clean guitar sound (All presets and FX off). However, the sound from the headphone output is great and without any defects. It feels like a badly-assembled hull combo. What to do with this? Have you encountered such problems? I attach a video. https://drive.google.com/drive/folders/1ItBycqPpDgfb10PJdC3haA5w-OeJ1hD0
Why does my code 50 amp cut out? Also, has loud crackeling sound when it's working. Sounds like a blown speaker but it's not. The master volume is only turned up 1/4 of the way and it's loud. Problems still remains even at lower volume. slight delay on the footswitch also when changing from one preset to another. Frustrated in Detroit.
My Marshall Code 100 Combo Amp is making a ringing noise unless i push the the bluetooth Pair option.. none of the knobs or presets will make it go away. however if i turn the master volume up all the way it will slowly as the master volume goes up make the ringing noise quieter.. is it the speaker for the bluetooth or possibly the speakers in general... i literally just bought it and feel like i wasted my money.
Hello guitar players,
today I got my new Code 100 head and connected it with my 2x12 speaker 1936 from marshall. I tried the presets and they sound very cool but the sound is in my opinion a little bit to muffled and not clear enough.
So I kicked out the cabinet in the settings and then the sound is very clear and cool for me. But whats exactly the sense of the cab when it sounds not good in my opinion. Do I really need them?
Thanks for your answers! :)
Presets need to flow easier between the different management areas.
(Reading the following is really only cumbersome, because that's how cumbersome it is to manage CODE.)
Copying one by one between amp and phone is really cumbersome.
How about an option to copy all 100 presets (or sections) between amp and phone? Both ways.
I want my amp to have the same presets as my phone.
(Others can still have the option the way it is laid out, but I don't see how managing amp and phone separately is useful unless someone really needs 200 different presets in one session.)
I like to have my preset sequenced in a way that makes sense. Artists, cleans, crunch, OD, Amps, or new additions squeezed next to existing ones. Others may sequence by set list or bands. If I shuffle presets on the computer/gateway, then the phone syncs this new sequence, and the amp does not match. Gets confusing.
Additionally, if the footswitch is assigned from the amp, then I have to copy new presets from phone to amp and even reassign to footswitch. Too many steps.
"Just use the presets on the phone and forget amp presets" would be an answer, but what about footswitch? and what about dead or forgotten phones?
Easy (automatic?) sync (with on/off for this auto/sync) between phone and amp, would allow everyone to use the amp (and footswitch) without constantly pulling out the phone and pairing to have presets from the phone available. Bluetooth drains batteries.
Btw, any phone sounds come on the speaker when playing because my iphone6 sees the amp as a headphone. So the presets need to be on the amp for any gigs.
Another footswitch suggestion:
A setting or function where the first 30 presets (01-30, without 00) are loaded into the 10 banks on the footswitch automatically? Then I only have to manage my presets within the 100 and everything else is assigned automatically?
This really stinks...
I have a brand new Code 25 and it stops playing through the speaker after a few seconds. The output is always there when I plug in a headset, but the speaker plays for a few seconds then goes quiet. I redownloaded and installed the firmware. I tried different settings and different presets. Nothing works. Any other advice before i talke it back to the Guitar Center?
Hi. First just to say that a am generally very happy with the CODE50 & it is definitely filling a gap to provide great practice tones with aux input from LickLibrary & my son's vdrum set to jam along! I have a coupe of items I wanted to put out there to the forum:
So the fizz - has anyone else noticed a very high end (treble) fizz or harsh crackle to the tone on most 'unsaturated' presets? It almost sounds like a digital clipping at the high end of the spectrum to my ear. It is definitely worse when using my 2015 Gibson Les Paul Less+ (which has the brass zero fret nut) like the amp is reacting to some of the pronounced higher frequencies on this guitar but it is also noticable with other guitars using a standard nut material.
The cabinet resonance I guess is due to the relatively light weight MDF that the cab is constructed of which appears to vibrate a little too readily has the master gets to about 1.5 / 10. I have dabbled a little with the resonance / presence settings under the speaker cab which has helped control it a little but I would be interested in any other ideas for reducing that boooom that can wash out the tone. I do have a 4 ohm Celestion G12T-75 from a long broken Marshall SS 50w combo which I am thinking of trying out - it is a physically heavier speaker than the CODE one pre-installed but I don't think structurely this will be a problem for the cabinet. I would appreciate any other ideas - anyone added noise suppression foam to the inside of the cab (as used in noisy PC towers) or anything else?
What options are available to replace the stock 4 ohm speaker that comes in the Code 50? I would like to upgrade to a Celetion or something similar. The stock speaker flutters at volume when using the heavy distorted/gain presets. Any recommedations?