Salve! Non riesco a collegare il code 25 al sito My.marshall per provare i preset disponibili. L'appplicazione gateway si collega e la luce azzurra si blocca riconoscendo il Bluetooth.
Dal sito My.marshall mi dice codice non connesso.... anche se riesco ad usare l'applicazione Gateway e risulto connesso.
Qualche suggerimento? Sto usando Crome aggiornato con smartphone Android.
I have successfully saved presets to my iPhone and can play them using the bluetooth pairing.
What is the best way to permanently transfer or sync them from the iPhone to my Code 50 amp?
Hi, I just recieved my Code 50 yesterday "bought brand new" and the amp sounded great until i hooked up to my pc this morning and downloaded a featured preset not a communiy preset. I am running usb not bluetooth and its my studio setup. Now all the distortion and gain sounds like the input gain is wide open clipping the signal coming in at all volume levels, and on all distortion and od gain presets. I tried to reset the amp and did a firmware update now its litterally so bad you cant play it. This is certainly a software issue cause the effects and clean tones sound fine. This happened immediatley after i sent the preset usb from the website to the amp from the pc. Also i tried several guitars, usb cables, guitar cables and even my mac. just dont know wether i should send it back or if thiscan be fixed with a firmware patch or something , Thanks
I have had a chance to spend a few days with the Marshall code 25 and I would like to share with you a few of my findings. I have played guitar professionally for over 30 years and have had all makes and models of guitars and amps in my time, but in general I would have killed for the equipment available to guitarist today.
This is the point where I look at the Code 25 and think “that looks like fun”. I have a few amps kicking about already, mostly gigging volume amps but I also have a Blackstar ID-Core 40, so this would be in reality what I would compare the Code 25 against.
Firstly my experience with the amp and a look around these forums makes one thing apparent. This amp is well named because it is a bit of an enigma.Out of the box I would consider the amplifier not fit for purpose this is really down to a few reasons.
Firstly, some of the presets are just absolutely terrible, I mean some of the worst patches I’ve ever heard on anything, “Small combo” and the “Brit” overdrive amps for instance are shockingly bad. You can make the excuse that all amp and effects units come with bad presets. However this is usually down to strange or weird effects to give bizarre sounds to show off effects but that nobody would ever use in a musical context. However some patches (such as Small Combo) are just basic amp modelling with no effects and are still absolutely terrible. Maybe these sound better on the 50 or 100, but if that’s the case remove them from the 25 it just gives a bad impression.
Secondly, the amp is stupidly loud. I don’t know if this is a marketing decision, but Marshall should look at its target demographic. This thing is a small bedroom practice amp, maybe at a push for some very small live situations, but that is it. Why make the thing so loud? If you need to use this amp near anything over half volume you have bought the wrong amp it’s as simple as that.
Thirdly, some of the modelling is not all it could be with digital artefacts (in the low end in particular), and a fizzy noise gate that for some reason is on patches where there is absolutely no need to have it as the patch is pretty quiet. Once again this is not a professional gigging or recording product and it should be judgged accordingly.
The last bad point I would say against this amp is the tuner, both onboard and on the app are two of the least responsive and wildly inaccurate tuners I have ever seen. Really not even close to tune! Put this down to another marketing tick box.
OK, now the good points.
It seems pretty well made and solid for what it is.
I like the size and weight, ideal for a bedroom practice amp.
I like the complete range of controls on the amp, and how you can do everything on the amp that you can do on the app, and it’s easy to do. Great user interface design work.
I like the Bluetooth features and the app. I know people have had problems with Bluetooth, but both my IOS and Android phones connected right away and are stable. I can stream music no problem from outside the house or in other rooms with no issues.
I like having 100 presets to store all the patches I could want (My Blackstar only had 6, and you can only have 1 for each model).
The headphone socket sounds OK, but if I wanted that as a primary feature I would have just bought headphone amp with effects.
I don’t use the recording over USB feature. If I did I wouldn’t expect something this cheap to be amazing. Once again if you want this you probably have bought the wrong product, and are in the wrong price bracket.
I like the cost, its amazing what it does for the money.
I like the sounds, now that I’ve got rid of the awful ones.
It looks pretty cool.
It’s a Marshall.
To make this amp useable, I basically had to do the following:
Overall I like the amp and doing just these 2 thing make it much more of a pleasure to use. The volume level are more what they should be for a product of this type and I don’t ever hear any of the awful patches (there are plenty of good ones).
Maybe other people can share their first experiences or tips with the Code 25?
Marshal code 25 has stopped syncing with the cloud. But there is a bluetooth connection.
There are 169 presets saved in the my gateway cloud that is some are repeated and cannot be deleted. Help me please!
I have a Marshall Code 50 running MCU version 1.44 and Gateway (Android version 1.5.5) on a Samsung Galaxy S9+ running the latest OS. I can bluetooth pair to the amp and play music, but can not connect to the amp to change my presets from the library. I have reloaded the latest firmware on the amp, deleted and reinstalled the Gateway app, paired and unpaired several times. Nothing seems to work. I even grabbed my old Galaxy S7 Edge phone and that Gateway app on it does the same thing. Does my amp need to be serviced for Bluetooth connectivity?
Hey, about a month ago, the preset readout faded to being almost unreadable. Then today, it stopped working completely. I can't use it for my guitar or as a Bluetooth player. Not sure what to do next?
The first issue was no bluetooth communication with my Ipad. I now use a Kindle fire and it's working great. Now I will be playing a preset and the volume drops out to almost nothing. Has anybody discovered a fix? This is a Code 25 I really want to love this amp because when it works it's great. The problems it has are making me fall out of love fast. I expected a lot more from Marshall, I have almost all Yamaha product and never have problems.
You need to get someone to fix the Bluetooth capabilities with this product line, like, yesterday. I updated the firmware yesterday, which was extremely difficult to do in the first place, uninstalled / reinstalled the Gateway app today, and still cannot connect to the amp except via my phone's native Bluetooth options to use it as a speaker. I am running ios 13.3.1.
I've scoured your web site, I've watched your videos, I've been all over Google and Youtube, and I am nowhere. In addition, I'm legitimately concerned by other reviews that the amp is simply not going to sound as good given I've updated the firmware. Will post again if that's the case.
I will see if I can push new presets to the amp via a hard connection to my PC, but you need to do serious damage control on this product line considering your leading selling point has proven to not work as intended, if at all.
I bought a new phone and now I can't connect to the presets on the amp.
I have a iPhone X.
I updated the firmware to 1.45
I've reinstalled the app, restarted the amp, etc etc
And yes I'm logged on to the amp and connected via Bluetooth in the phone.
I Just can't connect to the amp via the app, The app can't find the amp via the search function..
I just received a Marshall Code 25 as a gift and I am new to guitar playing and using an amp. So I have 2 questions actually.
1. In the User Presets section, what does the X over the amp (code not available) exactly mean?
2. I managed to connect the bluetooth on my iphone with the amp, and it works fine, but everytime I turn my amp and the app on my phone on, my amp doesn't show in the amp. So I end up having to sync the bluetooth every single time I turn it on, let it search for my amp, and then I can get started. Is there some reason why my amp doesn't stay in the app?
I own the Marshall CODE 100H and CODE 212 cabinet.
I really love this amp, but I find the MY GATEWAY web page interface to be somewhat awkward to use.
The following are issues that I would like to see changed.
All references to the MY LIBRARY list are referring to the list below the MY GATEWAY List on the MY GATEWAY web page.
1) On the My GATEWAY web page, the preset list at the top is arranged by columns (as it should be), but the MY LIBRARY list below that is arranged by rows.
This makes it very awkward to find a preset in the MY LIBRARY section.
The MY LIBRARY section should be arranged by columns as well.
2) There is no indication in the MY LIBRARY section on the MY GATEWAY tab whether a preset is or isn’t in the MY GATEWAY list.
This makes it awkward to know which presets from the MY LIBRARY are used in the MY GATEWAY
I would suggest adding the MY GATEWAY preset number to the MY LIBRARY list as the indicator.
3) There is no indication in either list whether a preset has been Modified or is a Factory Preset
(must copy to MY LIBRARY section below and then edit to know if it was changed-not as convenient as it could be if it was marked as Factory Preset or Modified in the list)
4) There is no way to compare presets in the MY GATEWAY list vs the same named preset in the MY LIBRARY list.
(And a preset can be changed in the mobile app or on the amp and synced to the web,
but the change doesn’t get applied to the same named preset in the MY LIBRARY list,
so the MY LIBRARY presets become inconsistent with the same named preset in MY GATEWAY.
And, there’s no indication that the same named preset in the MY GATEWAY list is now different from the MY LIBRARY version.
Must be constantly manually checking / updating the MY LIBRARY list.
There should either be a “Date Changed” field in the Edit Preset dialog box so you can know which one is the most recent, or
There should be a prompt or checkbox to update the MY LIBRARY preset as well.
There should be a way to select two presets and then select “Compare”.
The compare screen should highlight the differences.
5) Renaming a preset in the MY GATEWAY section doesn’t also rename it in the MY LIBRARY.
Requires either deletion of the preset in the MY GATEWAY list and re-addition of the renamed preset,
or edit same named preset in both lists. There should be a prompt or checkbox to update the MY LIBRARY preset as well.
6) Multiple presets can be named the same thing but have different configurations (really bad idea!)
This makes it hard to know which one is the most up to date.
This should be prohibited.
Copying a preset to the Library should pop up a warning message that a preset with that name already exists, and ask to replace or rename it differently.
7) Preset settings can only be viewed / edited in the MY LIBRARY section but not the MY GATEWAY section.
This means that you have to copy a preset from the MY GATEWAY list to the MY LIBRARY section first.
Then hunt down where it went in the MY LIBRARY list in order to edit it, Edit it, and then copy it back to the MY GATEWAY list.
That seems to be a lot more awkward than it ought to be. It should be possible to view or edit preset settings from either list.
8) It would be nice if a preset could be marked as a favorite.
9) It would be nice if all Factory Presets had audio preview samples.
10) It would be useful to have a way to record a short audio sample via bluetooth on the mobile app and then be able to save it automatically to SoundCloud and add the url to the preset.
11) Where do I find backing tracks for to use with the amp?
I recently purchased a CODE 25 and love it. In the Gateway app I see a different list of presets when connected via Bluetooth versus not. Any suggestions of how to correct?
When not connected I can see presets like Purple Plexi and Sweet Jubilee. Would like to check them out.
Hi I have a CODE 100H head/cab and a CODE 100 combo both with the latest firmware re-installed from Marshall and both have this issue, i.e. the amp very oftenn completely freezes when I save a preset.
Steps to reproduce:
- Modify any patch on the front panel
- 50% of the times the amp seems to freeze. The preset is saved but you can no longer change preset and there is no sound coming out.
The same happens if you modify a patch from the iOS app via bluetooth and then save it from there.
It's REALLY frustrating and I can't believe I didn't find anything on this forum under the "crash on save" keywords. Seeing it happens on both of my CODE units it much be a software bug, I don't think it has anything to do with my units.
Anyone else has seen this problem?
I was having difficulty syncing my gateway app to my Marshall.com to add downloaded presets to my library. On the forums Marshal suggested doing a factory reset by holding the amp button down while restarting the amp.
I did that. Now when I try to Bluetooth connect the gateway app and the amp I get this an error that says "connection rejected. You may only control amps you are already connected to for audio output".
I have restarted the amp and phone but I keep getting the same error message.
please advise on both this current problem as well as how to sync my gateway so that the downloaded presets get added to my gateway library.
Hi! I have an issue while trying to transfer dowloaded presets to my Code25. It occures both usb and bluetooth connections. On a usb connection i click the “amp” icon on a preset, it’s name appears on a Code screen. I push and hold store button on amp, “saved” appears. But then Code becomes freeezed, it does not react on button push etc. when i switch it off and then switch on it works fine, preset available on amp. The same issue appears when i try to transfer presets using Gateway app. What I do wrong?
Running V1.43 firmware.
I have followed all instructions and can not get the iPad 6 to connect in Gateway app.
It, however "pairs" just fine Bluetooth wise on the iPad 6!
AND Gateway works well on my iPhone 5, switches presets and everything.
So I know I am doing this right and the Marshall code 100 Head is responding via Bluetooth (with my iPhone 5) but NOT with the iPad 6.
Edited: Its the damnedest thing. I removed and reinstalled the app on my iPad 6 at least 8 times with the same results.
Then I reinstalled and paired the "9th" time, and it worked!!!!
I can turn the 100 Code head amp off, and back on and it still connects.
I'm glad it works now, but I dunno what I did differently.
Marshall finally released V1.43 of the Code Firmware. My phone finally connects reliably over Bluetooth which is a plus. It sounds like 3 different devices can now be paired too. A little disapointing that no other presets or other functionality was added but at least this major issue was fixed albeit after a UNACCEPTABLE time frame. I expect more from Marshall.
I've owned the new Code 50 for only a few days so I'm still a novice navigating through all the features. I'm just getting into using the My Gateway app from my Iphone and noticed when I'm connected to the amp through Bluetooth and I have the "blue" presets showing on the app which are completely different than the presets I see on the amp when I'm not connected through the Gateway app. So for example when connected through bluetooth I see preset 00 as EL34 Heaven on both my phone and on my amp, and when I'm not connected through bluetooth preset 00 is JTM Chill. I like the settings on the gateway app much better than what I have for presets when just using the amp without bluetooth. I guess what I'm trying to do is find the easiest way to say replace 00 JTM Chill with 00 EL34 Heaven so I can have 00 EL34 Heaven on the amp without having to connect using the gateway app? I've look at other questions and cant seem to find this answer. Is this the sync function?? Thanks in advance.
When I try to save a preset to the amp, there is no problem. When I try to save a preset to my library I get the message: Patch cannot be saved; sync with Marshall server in progress. My gateway has both a Bluetooth and an internet connection. Logged into my.marshall but nothing happening. Sync button is disabled. I feel like I'm missing something in my understanding of this aspect of the Code/Gateway system. Is there a user manual for the Gateway app?