Questions
Showing results 1 to 20 of 1393
0

votes

0

answers

3

views

I have had my Code 50 for a while and have played around with it to no avail. It's 20-50X too loud. When I set the Master Volume control to something like .5 it's way too loud. I can adjust the volume within the preset but if I change to any other preset it almost knocks my house over. I think this amp is unusable and has some serious design flaws. Is there a way to knock down the volume for the entire amp and all the presets? I need them all set at around a .1 or .2.

asked 28 Nov 2021 at 10:09 PM

Scott Jones
0

votes

3

answers

23

views

When I use my marshall on the pc I get really strong buzzing when recording and hearing.

I tryed 3 different cables, and updated the firmware 3 times already.

I'm out of options, this turned to be a nightmare to me.

asked 27 Nov 2021 at 02:39 AM

Marcelo Vitor Pinheiro
0

votes

0

answers

8

views

hy

marshall gateway app is not working with android 11 version

the bluetooth connection is in place (blue light is in on) but opening the Gateway App the connection to the amp is not detected

can you please give me the info to solve the issue?

i've tried with another phone with android 10 sw version and the app is working

I think the app need some update to fix this bug (my version is 1.5.5 )

please consider that android 11 will be the standard for the most part of your code owner in the world

best regards 

Luigi

 

asked 26 Nov 2021 at 08:26 AM

luigi pagani
0

votes

1

answer

44

views

How do I have chorus & flanger at the same time 

asked 19 Nov 2021 at 04:23 PM

Robert Smith
0

votes

1

answer

56

views

Does the Marshall Code 100 take pedal well? 

I'm considering buying a wah pedal but I'm not sure if it will work well with the amp. 

asked 17 Nov 2021 at 10:21 PM

Zen Guitar
0

votes

0

answers

27

views

I bought a midi controler, but i dont have de marshall code to program the midi control

asked 16 Nov 2021 at 06:24 PM

Eduardo Pugliesi
0

votes

0

answers

32

views

Hi there, just purchaced a Code 50, installed the Gateway app for iPad. All working a treat, eccept that if I am connected to the Amp via bluetooth, I am getting all the keypad sounds through the amp, also incoming messages, email notifications and phone calls. is there a way of stopping this????

asked 14 Nov 2021 at 08:16 PM

Christopher Read
0

votes

1

answer

52

views

Had Code 50 for a few days and the LCD display is now not lighting up orange,

it still works the same but no light and quite difficult to see in dim light.

 

Any Ideas ?

 

edited 15 Nov 2021 at 08:27 AM

Chris Hornby

asked 12 Nov 2021 at 06:46 PM

Chris Hornby
0

votes

3

answers

77

views

When I select the tuner the display only shows.  C : > | . I think the firmware is M1.1.

Any ideas? Thanks

 

asked 11 Nov 2021 at 09:24 AM

Bill Jones
0

votes

0

answers

24

views

Is there a direct connection from the Code 100 amp to a Scarlett audio interface?  

asked 11 Nov 2021 at 03:09 AM

Matthew Kernodle (1)
0

votes

1

answer

72

views

The output does not switch to earphones only when earphones are plugged. Both speakers and earphones still output sound. Works fine with huge headphones but wonder if theres a way for it to work with earphones/earbuds/headset too. Thanks.

asked 10 Nov 2021 at 07:48 AM

Clarence Muljadi
1

vote

1

answer

61

views

Looking at online forums, a lot of people appear to have a hard time getting a decent sound. Here's some tips that work for me, using a strat

1. Treble on 4, for everything. Presence on 1 for clean, 0.5 for dirty. Resolution on 5

2. Bass on 4 for american clean preamp, 6-8 for all others

3. Middle on 2 for clean, 5 for dirty

4. When using the onboard distortion pedal for blues keep the drive low = 1-2. Set amp gain at about 3 or 4

Hope this helps

 

 

 

asked 08 Nov 2021 at 06:25 AM

fred cav (1)
0

votes

1

answer

55

views

A lot of stuff about this so not an isolated problem. Getting really fed up with this amp and probably going back to pedals rather than presets. Is there any recent news on a fix for this? If not going to trash this expensive disaster and consider Fender Mustang.

 

asked 07 Nov 2021 at 09:15 PM

Tony Wetherall
0

votes

1

answer

82

views

My CODE25 was repaired by Marshall in September after the amp itself kept crashing and the sound was cutting out. It has now been returned in an even worse condition.

On switching it on, the message 'Hold 'Store' to reset' appears on the screen. I press store and nothing happens. I am unable to access the amp presets.

After 10 minutes the mobile app then also freezes. I have contacted my Marshall dealer who sold me the amp and they have asked me to contact you for a resolution before I can send it back to them.

FYI: I have uninstalled and re-installed the mobile app without any resolution of the problem. The amp is is of no use and even a factory reset and firmware update has not solved the problem. I am gradually losing my faith in Marshall CODE products.

Do you have any solutions?

asked 04 Nov 2021 at 02:15 PM

Gerry McIntosh
0

votes

1

answer

74

views

The Marshall Code 50 I bought losses sound while in use. Turn the power on and off sometimes fixes it and also disconnecting it from the bluetooth device. However, recently I don't even connect a bluetooth device like my phone to avoid it, it still happens. Already tried installing the lates firmware, done factory reset, and still having this problem. I'm from the Philippines, the seller did not reply when I asked for assistance. I also don't know where I could bring it for technical support.

asked 04 Nov 2021 at 07:16 AM

Roger Brigido Lagatic
0

votes

1

answer

106

views

Hi everyone, I would like to know if the new firmware 1.46, aswell as it fixes the screen flickering on the code 25s, also fixes this on the code 50s, the amp panel flashing together with the button lights when turning on. I don't know if it supposed to be the same problem as in the code 25.

I don't have one yet but already ordered one so I want to know every single thing that could happen. I get a bit afraid when I see negative reviews, so maybe this new firmware fixes most of the problems. 

Regards

 

edited 31 Oct 2021 at 11:06 PM

Federico Slandrix

asked 31 Oct 2021 at 08:36 PM

Federico Slandrix
0

votes

0

answers

37

views

Hiii

Last month (Sept. 2021) I was able to sync my Amp with the Gateway app. Unfortunately, This month/Today the app cannot detect/connect to my amp.  I already updated the firmware of my Code 50. Is there a way to sync it? because I already did what the tutorials said.

 

Thank you.

asked 30 Oct 2021 at 07:27 AM

Gabriel Sumat
0

votes

1

answer

67

views

Hi!

I bought a Marshall CODE 100w in Feb/21. It wasn't even used 10 times.

Yesterday when I went to turn on the equipment, the amplifier started to make a noise. I thought it might be the cable, but it wasn't.
Even without the cable connected to the equipment, the noise continued.

I reinstalled firmware but it didn't work either.

I do not know what to do.

Could you please help?

asked 28 Oct 2021 at 05:22 PM

Linneu Silva
0

votes

1

answer

46

views

Hi all

Very often when I press the down channel button on the pedal, the amp goes UP and channel!

Its a pain in the but, makes it impossible to play with,  tell me there is a fix for this?

Thanks all!

asked 28 Oct 2021 at 12:51 PM

Matt Sykes (1)
0

votes

5

answers

116

views

Hi everybody

My CODE 25 was working like a charm. After the firmware update there is a horrible whistling high frequency noise coming out from it. It is really bad. 

Anybody can help me out with this? How to roll back the firmare?

(It's not the guitar/cable/ground because I have another amp and I did a test)

Thanks

Matteo 

asked 26 Oct 2021 at 09:29 AM

Matteo Bassi
Showing results 1 to 20 of 1393
Loading - please wait...