I recently hooke this head unit up to a 2 2x12 cabinet 8ohm and per instructions and at full cranked volume barely hear anything
Any suggestions or tips before persuing it being faulty? speaker cable hook up and checked with another cabinet and still same thing barely any volume .
Hi there - I picked up a DSL1 in Leeds recently on tour and the direct out / speaker emulation is very dark - I checked frequencies in Logic X, theres basically nothing above 2.4k. When I run the DSL1 send into the return of my JMP-1 (Rack Unit) to use the emulation it sounds great - and I get spikes a little over 5k. Is it a defective unit or is that simply the sound of the simulation? I have used different Marshall amps direct over the years - (Valvestate VS100R, JMP-1, TSL100) and have had great results with all of them until the DSL1. Cheers for your help,
Dylan
Hi there - I picked up a DSL1 in Leeds recently on tour and the direct out / speaker emulation is very dark - I checked frequencies in Logic X, theres basically nothing above 2.4k. When I run the DSL1 send into the return of my JMP-1 (Rack Unit) to use the emulation it sounds great - and I get spikes a little over 5k. Is it a defective unit or is that simply the sound of the simulation? I have used different Marshall amps direct over the years - (Valvestate VS100R, JMP-1, TSL100) and have had great results with all of them until the DSL1. Cheers for your help,
Dylan
Hello,
The manual is very sparse about this. Could you please clearly outline the steps needed to safely operate Origin 20H with no speaker connected when using DI out for recording?
Is the DI out mono unbalanced or "stereo" balanced jack socket?
Regards
Marek
Hello,
I'm having a problem when I recording my guitar.
My recording guitar setup is:
Gibson Les Paul Studio -> Bugera 333xl Infinium Head Amp (with instrument cable)
Bugera 333xl Infinium loudpeaker output -> Active DI Box Behringer Ultra-G (with speaker cable)
Active DI Box Behringer Ultra-G Direct Link -> Marshall 4x12 MX412B (with speaker cable)
Active DI Box Behringer Ultra-G Output -> Presonus Studio Live AR16 USB Mixer (XLR cable)
I'm using Logic Pro X Software.
I record a guitar riff in Logic Pro x as audio track (audio_1) and then i want to record a second guitar like a fill guitar or lead guitar (audio_2).
To record audio2 i turn on audio1 to listen the guitar riff.
When i’m gonna listen the audio2 in solo mode besides the lead guitar I can listen the sound of my audio1 with very low volume but i can listen it to
Can you help me with this problem please ?
Best regards
After about 3 months of very light usage (home use, ~20 hours), my Code 50 developed a harsh noise problem: https://youtu.be/S2cTK8fsfTE. It's on every preset and can be heard via the speaker and when using headphones. I tried using different guitars/cables/power cords/rooms/outlets, reloading firmware, and resetting the presets to factory default; but the noise continues. Anything else I can try before I return it for replacement/warranty work?
Bought a new Stanmore II speaker. Worked fine for few hours however now after few minutes of play it automatically turns the volume to Full. I reduce the volume and again after few minutes it goes to full on its own. Tried online, offline content playing but same problem.
I just bought a used JMD 100 watt head , it sounds great going through my 4 x 12 cab .
I was trying to do some silent recording and the emulated out doesn't sound very good , neither does the headphone out.
Rhythm sounds good but the solos sound like there is no IR .
I tried plugging the speaker out into my Torpedo Two note captor 16 but I do not get any signal.
Does anyone know why the Marshall JMD-1 does not send or the Two note does not receive?
The Torpedo Two note captor 16 works fine on my Bugera 1990 .
Is this a fixable problem ?
Thanks
Max Gain
Does disconnecting the speaker disable the power section?
I've seen in other answers that you can disconnect the internal speaker in the DSL1CR combo, and use the emulated out.
However, is it necessary to have the emulated out connected? Can I use the effects send instead (to get just the preamp output)?
I'm worried about stressing the power section from it not having any load, but if disconnecting the speaker disables the power section this should be fine, right?
Hallo,
cannot find any technical detail on this speaker. I would like to know the Sensitivity (is it 100db as the Vintage 30?) and the Frequency response diagram as well for the 16 Ohm type. I'm gonna to buy a 1936V 2x12 speaker cabinet and I would get these information, please.
thank you.
cheers
Hi,
guessing my asking this as a comment on another post got it lost.
can you explain how to use the DI please? Do I disconnect the speaker? Is the output line level? Does the powerstem have any effect?
new to having valves, like the amp but really would like this clarified.
ali
Hi. I recently purchased an Acton II wireless speaker with Amazon Alexa. Will it work using my Kindle Fire? It also has Alexa.
Hi Guys,
got an origin 20 combo, trying to use headphones on di out. What am I doing wrong? Got speaker working but no sound in headphones.
I take it first thing is unplug speaker??? Then what, do I need to change the power setting or something?
hanging off till I hear more.
ali
Hello,
My nephew recieved a Stanmore II bluetooth speaker for Christmas and he's having problems with adjusting volume with his phone on bluetooth. Most of the time, he will turn the volume up or down on his phone, but the speaker volume doesnt change. Sometimes though, it does work. Late at night he will put a song on and have to run across the room to turn the speaker down because it will wake everyone up and the phone adjustment won't work. Any help is appreciated. Thank you.
This is killing me! total dealbreaker. If I can't find a solution I'll return this speaker which I love everything else about it.
It goes to auto-standby if it's unused for 20 mins regardless of bluetooth use or sound coming from RCA jack. But whenever I play something next time, I have to touch the knobs to wake it up manually. I put the speaker in my bookshelf which my plan is to not need to touch it in every use.
I want it to not go stanby mode ever. Is it possible? I couldn't find any answer in the manual, in the forum or in any other place. Sent a support inquiry as well, but I'm curious if anyone else is having same issue.
all sorted
Manual says "Connect a single speaker cabinet here for the DSL1HR head". Is it means I can't use cabinet with two 8ohm speakers in series?
Hello i'm Daniele and i have a question regard the DI connection of my new Marshall 1959 sv20h:
If i connect the head trough DI out, I must connect also a speaker?
Thank you in advance
Best regards
Daniele
Hi folks!
My brand new DSL20HR has a great sound with my MX212AR cabinet, but when I want to plug it on my mixtable with the emulated output the sound is very bad.
I've tried it on the STB position with my speaker plugged. The sound is bad even with the headphone : a lot of hum and the volume should be at the max.
There was a lot of highlights on these feature :
"Marshall has teamed up with software mavens Softube to create exceptional tones "
I don't understand it can work so bad. I really can't use it and I many other users that seem to have the same problem.
Thanks for your help.
Best regards.
Pierre
Hi Everyone.
I currently own a Marshall Acton II speaker. I wonder if someone really uses a 2 speaker coupled, in order to improve the stereo capabilty.
Does it really worth it buying a second speaker?
Thanks everyone.
Regards
Luis