Questions
Showing results 201 to 220 of 3523
1

vote

0

answers

568

views

For all you that have issues connecting amp with Gateway app (even though it's connected to your phone already) clear out all of your old bluetooth pairings (headphones, portable speakers, etc..).   That worked for me after screwing around for 30 min.  

asked 13 Apr 2020 at 09:37 AM

indy jonz (2)
1

vote

3

answers

2.2k

views

Hello.

I've been using the Marhsall Monitor bluetooth headphones for about a year and I haven't had any issues using these in rain or during really sweaty sessions at the gym. I'm now looking to upgrade to the Marshall Monitor A.N.C. II. And from the promotion video posted by marshall(https://www.youtube.com/watch?v=xMy3OXCXZvk) I see at the 1:17 mark that(what I assume is) the microphones for A.N.C. will be located on the top of the headset.
Will this pose a higher risk for water damage on this headset modell?

See screenshot from promotion video:

Thanks for any type of response.

B.R.

Kristoffer Hellstrand

edited 11 Mar 2020 at 08:06 AM

Kristoffer Hellstrand (2)

asked 11 Mar 2020 at 08:05 AM

Kristoffer Hellstrand (2)
1

vote

2

answers

943

views

Can anyone help me with a blues tone for the guitar? i am a litte bit confused about the amps/preamps etc ... (ESP Ltd ec 256 FM)

Also i would like to tell me a lead tone as well...

Thank you in advance

asked 20 Feb 2020 at 01:29 PM

Haris Orfanidis (1)
1

vote

2

answers

795

views

Hi Marshall, I have just purchased a Code 100h and 412 that sounds great, however, I notice that when I play a chord there is a sound coming from the amp after the chord dies down that sounds like a cyclicle click and hissing. I have tried different leads and plugged it in a different socket but still get this consistantly after holding a chord down?

asked 18 Feb 2020 at 11:35 AM

Michael Lawson (2)
1

vote

1

answer

803

views

I recently connected my code via usb....went to ACDC preset, downloaded to test it out...I liked it but didnt save it...now when I come back to save it nothing (any preset) will not transfer to my code....It reads CODE connected....Help please!!!

asked 20 Jan 2020 at 02:02 AM

Eric Deaver (1)
1

vote

4

answers

2.8k

views

Hi! As the tile says, does Marshall have any plans to make the CODE EDITOR for Mac as well?

edited 24 Dec 2019 at 02:51 AM

Omar Calero (3)

asked 24 Dec 2019 at 02:50 AM

Omar Calero (3)
1

vote

0

answers

730

views

Hi

I purchased a Marshall Code 100H in April 2019.

It was replaced under warranty last week by the retailer as it had developed a constant electronic beeping sound.

I received the new head and right out the box it was much improved. I decided to get to grips with loading up my presets and patches so began by carrying out the latest firmware update as advised by Marshall, alas, the electronic beeping sound has returned.

It is constant and present with or without a guitar plugged in, elevates with master volume, cannot be fixed with a noise gate, the amp has been plugged in several different venues and the noise persists and it was not auidable before updating to firmware V1.44.  Jul 2019.

Is there a means of rolling back the firmware or is there a known fix for this issue, it doesn't seem fair the retailer has to replace another amp which was fine until update was applied. Any advice would be much appreciated.

Thanks

asked 25 Nov 2019 at 06:11 PM

craig Humes (1)
1

vote

0

answers

904

views

Hi. I have a question: The Code USB interface is ok only with pc or it work with really usb midi? With usb midi pedal like Midi commander by Meloaudio, for explample, work or not?

if it work only with pc like daw is very very poor choise. next firmware? the orignal PDL 91009 is ok, but it's very very limited.

thx 

paolo

asked 19 Nov 2019 at 05:32 PM

Paolo Goi (1)
1

vote

1

answer

1.3k

views

This is a follow up related to registration. Or, more appropriately, the inability to use the online website to do so. I managed web development and support teams for 35 years. Your answer is to email support...? Have you thought about actually fixing the problem at its source? To ensure your website is accessible and actually works? There have been many questions/issues raised related to this, spanning years. Do you have a development team? I'd be mortified if I were the manager in charge of this website. On the flip side; the amp is great! I love Marshall. Always have. This is just disconcerting. I hope I don't need any "real" support via the web. Something more complex as registration. God forbid. Sigh.

Dennis

asked 19 Nov 2019 at 01:33 AM

Dennis Watts (1)
1

vote

2

answers

1.4k

views

The manual that came with the head says use output 3 when using a single 8 ohm cab. 

The online manual on the Marshall website says to  use output 2 when using a single 8 ohm cab.

I  have plugged a single cab into these both  at different times and output 2 seems to have more volume and treble than output 3

I am slightly confused and annoyed as shouldn’t  either 8 ohm output sound the same irregardless of which one I plug my single 8 ohm cab into?

I would appreciate some clarification so that I can use the correct 8 ohm output for my speaker cab!

Update to my original post as I  have an additional question related to rear speaker outputs.

The third output speaker socket and the revised manual show this as output for 2x16 ohm. (Mine has the modified sticker attached)

Does this mean:

a: that you can plug two 16 ohms speaker cabs which have been set up in parallel into output socket 3 and the power amp sees a total of 8 ohms? .

b: output socket 3 already internally wired in parallel with socket 2 and such you plug one 16 ohm cab into socket 3 and one 16 ohm cab into socket 2, for a total of 8 ohm impedance?

c: Not sure what else could be possible?

Could you please confirm which is the correct approach? Thanks, Ross

edited 01 Jun 2020 at 03:44 AM

Ross Ferro (1)

asked 13 Nov 2019 at 11:11 AM

Ross Ferro (1)
1

vote

1

answer

727

views

Good day. Yesterday I bought Marshall Mode EQ headphones and ran into a problem.
Smartphone ASUS Zenfone 4 max, Android 8.1.0. When the headphone cable is shaken while listening to music, the volume on the smartphone spontaneously decreases. What can you advise?

asked 13 Nov 2019 at 07:17 AM

Vitaly Andreev (1)
1

vote

2

answers

2.9k

views

Je n'arrive plus a faire reconnaître mon téléphone dans l'appli gateway Marshall

Le téléphone se connecte via bluetooth mais l'appli ne me donne pas accès au réglage / pas de connection

Je ne plus piloter mon ampli avec le téléphone alors que cela fonctionnait parfaitement auparavant.

J'ai fait une mise a jour de l ampli par USB 

Quelqu'un rencontré le même problème ?

Merci pour votre réponse.

Éric.

asked 11 Nov 2019 at 02:50 PM

JACKOWIAK Eric (1)
1

vote

0

answers

558

views

I would like to know if someone is using code 25 for small performances with a band. Using i.e the headphone as line out to a mixer.

asked 08 Nov 2019 at 12:43 PM

ricardo albert (1)
1

vote

1

answer

925

views

Hi,

 

I recently buy a Code 100 head and 4x12 cabinet and I loving it!

But I do have one concern the hum,there is a humming noise coming from the speakers when not played or not plugged in?

When I put the power one the humming is there and when played humming isn´t noticeable.

 

asked 25 Oct 2019 at 04:24 AM

Teppo Salotuomi (1)
1

vote

1

answer

1.2k

views

Hi! I recently bought my Marshall DSL 100 HR. There is a silent recording mode. If my understanding is correct when the amp is in a standby mode only preamp section is active. Can I use my amp in standby mode for silent recording at home without a load/cab?

I would monitor it via my soundcard. Just to be clear I would not activate the 100/50 power amp section only stay in STB mode.

Could this cause any harm to the amp?

Thanks.

 

DSL

asked 23 Oct 2019 at 03:31 PM

Adam Adam (1)
1

vote

1

answer

931

views

I have recently had my iphone 8 software updated to ios 13.1.2 and since then have not been able to control my Code 25 amp via Gateway from my phone even though, in iphone settings, I am connected via bluetooth but within the Gateway App I'm not. I have upgraded my Gateway App to version 1.5 back in July and up to now it's worked perfectly well. Is anyone else having this problem and if so  is there an App upgrade?

asked 12 Oct 2019 at 11:34 AM

Brian Delaney (1)
1

vote

0

answers

597

views

Was curious if the footswitch on this is a short to sleeve connection.  Going to use a headrush gigboard with it using the 4CM but also want to contral the channels much the like the included footswitch does.

asked 24 Sep 2019 at 04:50 PM

Adam Goldbeck (1)
1

vote

1

answer

656

views

Is my first marshall amp and i have a doubt, i don´t know how to sort my presets, for example if i wanna move the number 10 to the place 2 only its copy and delete the preset from that place and then i have the same preset in two places, but i wanna only move the preset. thanks

 
 
 
 

asked 22 Sep 2019 at 06:35 PM

Sergio Geronimo (1)
1

vote

2

answers

1.2k

views

My question is concerning the Code 100H. When using an external cabinet, is it better to use the preset power/cab selections or to turn them off. Does this apply to the Marshall code cabinet and any other cabinet, or just to a different cabinet ie: 2x12 Morgan ? Thanks.

asked 03 Sep 2019 at 01:56 PM

oliver hoy (1)
1

vote

2

answers

1.7k

views

ive had a mg30cfx for a couple years now. the amp randomly cuts out every now and then. volume doesnt go over 3.... any ideas??

amp

asked 23 Aug 2019 at 10:27 PM

owen boyle (1)
Showing results 201 to 220 of 3523
Loading - please wait...