Hi,
I was wondering if i can use a A/B footswitch to switch between 2 seperate cabs while the amp is on, as the amp has a internal load?
Thanks Mark
Hey, about a month ago, the preset readout faded to being almost unreadable. Then today, it stopped working completely. I can't use it for my guitar or as a Bluetooth player. Not sure what to do next?
Hi.
Please could you tell me which of the wires in the pic. below are carrying the audio to the POWER AMP board on a CODE25 (red, yellow, or blue block)???
Regards,
Dale.
We have two Marshall Acton Multiroom that have the exact same issue. Whenever they have been plugged in the power for more than 24 hours the sound becomes distorted/crackles and it gets increasingly worse the longer the speaker is powered on.
The only solution we have found is to pull the power plug for a minute before plugging it back in. Then the speaker will play fine for another 24 hours before it starts to crackle again. However, this solution is very inconvenient.
We have reached out to the Marshall support but they are not much of a help.
Has anyone else found a solution to this issue?
I have successfully saved presets to my iPhone and can play them using the bluetooth pairing.
What is the best way to permanently transfer or sync them from the iPhone to my Code 50 amp?
Hi
I have recently purchased a Code 50 Combo Amp and am really glad I did as I am not gigging and to be honest the Code 25 would have been ample, the master volume is almost off and in my living room if I were to turn it up to a quarter I would lose my windows and my neighbours! Anyway my question is about the two mini jack sockets on the amp one for headphones one for mp3 player. Are they both stereo and can I use a phone or laptop as the mp3 input. I think I recently read an article that said they are dual mono. The reason I ask is I have headphones but no lead to connect a phone or my laptop so I would be grateful if you could tell me what to order on ebay. My email is daistar@hotmail.co.uk
Many thanks
Dave
The App will not accept my login details for syncing. It's the same details I used to login in here on the pc. What can I do to fix it? I already did a password change to see if that worked and yes, I have turned it off and on again. Any suggestions ? I am using my email as my user name, dont know if that is an issue but it is the only user name I have as far as I am aware.
My CODE25 was repaired by Marshall in September after the amp itself kept crashing and the sound was cutting out. It has now been returned in an even worse condition.
On switching it on, the message 'Hold 'Store' to reset' appears on the screen. I press store and nothing happens. I am unable to access the amp presets.
After 10 minutes the mobile app then also freezes. I have contacted my Marshall dealer who sold me the amp and they have asked me to contact you for a resolution before I can send it back to them.
FYI: I have uninstalled and re-installed the mobile app without any resolution of the problem. The amp is is of no use and even a factory reset and firmware update has not solved the problem. I am gradually losing my faith in Marshall CODE products.
Do you have any solutions?
Hi, is there anyone who is able to create a preset (patch) to get the sound of the Peavey Delta Blues out of the Marshall code 100 ?
Thanks.
Christiaan
Hello,
can I use my JTM60 speaker with a Marshall Origin 20H Head?
Also, my JTM60 has suffered some damage when my nephew tried to power on the amplifier, she cranked everything up but didn't succed, when I got home I didn't noticed it was all cranked up and powered it, it blew tubes and some more, I had it repaired but it didn't get back to the same sound as before... I'd like to have it checked by qualified personnel, can you indicate someone in Italy, please?
Thanks a lot,
Marco
Hello,
Does anybody have a clue when this Footswitch will be available in Australia??
If you don't know or the answer is NEVER, does any have an idea of another footswitch that will do the same job on my DSL40?
Thanks
I have the original Marshall Stanmore. It's wired direcly to both a turn table and a CD Player. The sound recently began cutting out intermittenly. I hear a bit of static, the audio cuts out, and then a few seconds later, the sound comes back. I've been using the same setup for about a year with no issues.
Any ideas?
I need a new circuit board for my Marshall 20/40 combo amp. I turn the amp on and it will play for a little while and then all sound ceases until I turn it back on. I've change out tubes to no avail and I broke out my old amp mod equipment and tested circuits. That's the only piece I am unfamiliar with so I'm thinking that's the issue. My vendor tells me they can't order it because the amp is discontinued. Where can I order one so I can fix my amp?
Last update 10th Oct 2017 v1.41 surely there has been something to update Marshall Team such as bug fixes and new presets since 18 months ago, or have you just forgotten us after having all our well earned money!
What are the steps to Backup my presets & patches on MyLibrary?
What are the steps to then load my presets to a friends Code 100?
Hello, code 50 footswitch . How do you re set foot switch to the original set up so that as you press each button 1,2,3, they activate one effect at a time. Currently for example press button one all three lights turn from red to green, or green to red
Will a firmware update get rid of the hum associated with the Code amps?
I have the Code 100 combo.
Thanx,
Bobby
I have all my Rammstein Albums ripped straight from the cds and I cant play them back? the app keeps telling me it is crashing as soon as I hit the ok for the amp to play it back. this is my second code 100h that actually ahs working bluetooth. thankfully I was given a replacement but I now suffer from this condition. I cannot play my own owned music and mp3 files from Fl studio to my amp. I buy a 100 watt head and cant annoy my neighbors???
There a many questions on this forum about the irritating noise with Code 25 and Code 50. However, it happens via the speaker only, not via the headphone connection. The presets sounds very nice in that situation. Can you explain?
Because of the noise issue I just use the Natural sound and add FX pedal effects. No noise at all. But that is not the way I want to use the Code 25. I want to use the presets.
Hello,
I'm having a problem when I recording my guitar.
My recording guitar setup is:
Gibson Les Paul Studio -> Bugera 333xl Infinium Head Amp (with instrument cable)
Bugera 333xl Infinium loudpeaker output -> Active DI Box Behringer Ultra-G (with speaker cable)
Active DI Box Behringer Ultra-G Direct Link -> Marshall 4x12 MX412B (with speaker cable)
Active DI Box Behringer Ultra-G Output -> Presonus Studio Live AR16 USB Mixer (XLR cable)
I'm using Logic Pro X Software.
I record a guitar riff in Logic Pro x as audio track (audio_1) and then i want to record a second guitar like a fill guitar or lead guitar (audio_2).
To record audio2 i turn on audio1 to listen the guitar riff.
When i’m gonna listen the audio2 in solo mode besides the lead guitar I can listen the sound of my audio1 with very low volume but i can listen it to
Can you help me with this problem please ?
Best regards