Hi,

I have a problem with my new Stockwell II. It plays the Bluetooth connection sound while playing music with my iPad Air, which is only 10 centimeters away.

The intervall between this sounds is not constant, between 30s and 15 minutes. But quite annoying. Music playing is not interrupted.

Any ideas what to do? Maybe a firmware update? (But my windows 8.1 pc doesn't recognize the speaker.)

Thanks!!!

Hello everyone,,

Hello,

I am experiencing some troubles with the battery of my speaker stockwell that I bought 2 years ago.

I would like to know the contact phone number of the technical service in Valencia (Spain).

Thanks.

For the past few weeks I've been hearing a scratchy sound playing with the background music during certain TV broadcasts (mostly discovery-like channels). It's almost an eery scratchy gieger counter like sound. It's fitting for the programs I'm watching (Strange Evidence, What in the World, Monsters Inside me), so I'm not sure if there is something wrong with my speakers, or if that's the intended sound.

Is there something I can play to test the sound output to know if it's my speakers crackling or not?

Hello,

I've had my code 25 for about a year and a half. After about 6 months sound from my amp speaker would stop after a few seconds after turning on the amp, however if I plug in the headphones it works fine through them, then if I pull out the headphones the speaker will sometimes work for a short while before stopping again.

After a few weeks of the sound not working, it will then start working fine for week or 2, before the sound stops again through the speaker.

It is not the cables or the guitar as I've tried multiple  on the same amp and they all work fine on my old amp, so I imagine it is a problem with the speaker/headphone socket?

Is there a simple fix for this or will it need to be returned under warranty? 

I was wondering if the creator of the KASHMIR preset would be interested in also creating the FLANGER part for KASHMIR using all the current preset settings (amp, cabinet, speaker etc) as a complimentary preset for the turnaround section of the song.  I believe, from forums, that a preset will switch better (Marshall CODE footswitch) if the preset has the same amp, speaker and or cabinet setting as it takes away the millisecond delay of switching between amps in a particular preset.  Look forward to your answer and or creation of said beasty.

Regards Kev

How can I update firmware when I don't have USB port on my Marshall speaker

Hello,

My new Stanmore 2 speaker isn't showing in the devices list on my Macbook Pro.

However, the macbook recognize my TV and my phone. Also there is no problem to connect my speaker with my phone (Huawei P20).

Please help !!

Thank you

I know that turning a "TUBE" amp on without a speaker load on the output will damage the amp.

(the no-load condition will cause the output voltage to increase until the output tubes burn out, which can then lead to other component  damage)

Is this also true for a CODE 100 amp?  Is there a risk of damage to the output section, with turning the unit on without a speaker cab load connected?

Would it be safe to operate the amp with just headphones connected instead of a speaker cab?

Would it be safe to operate the amp without either a speaker cab or headphones connected?

I ask because my computer (which is a desktop) is in a different location in my house than my amp.

Doing firmware updates or testing out patches requires either moving my computer or my amp, both of which are very inconvenient.

It would be much easier if all I had to move was the head.

do I need to have a speaker connected to thecode 100 if I am using headphones?

Hey Mates,

Having issues with a clients amp, seems that after a retube that i did, he was playing and after about 30 min, it gradually started losing sound and then cut sound completely.  I did the re-tube myself, and biased it properly and i was able to play it for about 40 min with absolutely no issues.  List of troubleshooting steps i have done:

tried a different speaker cable

tried a different guitar cabinet

tried a different guitar and guitar cable

tried the old tubes, additionally bought a 12ax7 and tested each pre-amp tube

tried a different power source

Have tried different power tubes

have checked and replaced the fuses

Now this is what i am THINKING is the problem, I think it might be something with either the heater curcuit fuse, or i think it's called a BRT1 Rectifier?  I did alot of research and it seems that the people having MY issue, explain the same symptoms of what i am having.

Now i have to make this clear, I AM NOT A PROFESSIONAL TECH, just a guy helping bands out with tech stuff that they don't know how to do.  So any help is appreciated.

Thanks!

Hello everyone,,,

I bought the Marshall Class 5 combo about a year ago, and while I think that the concept is fantastic, the actual product isn't. Unfortunately, I think the stock combo sounds rather terrible. Plugged into my 4x12 cab with Neo Creambacks, the sound is vastly improved, though, so I'm thinking about getting a 1x12 cabinet to go with the combo for smaller rehearsals and gigs. Now, the Neo Creambacks eliminate some of the fizzy, harsh and unpleasant frequencies from the combo at higher volume settings, but I'm hoping to get rid of them completely. I'm currently thinking about one of the following two speakers: the Celestion V-type (this would be my first choice) or the Eminence Governor (which people compare to the V30, but with less of the harshness). In your opinion(s), which one would best achieve the sound I'm looking for? xvideos xnxx xxx
 
Best,
Lincon

I recide to open my code 50 cabinet. It was not just a simple sound change matter. For me this cabinet is the low point in the project. With this upgrade I believe now th speaker moves freely. Of coarse you have all those open cabinets advantage, more crystallinity, less punch low freequencies, more spacial sound distribution (less directionality)... For me the stage effect was quite positive. Some time ago I was really deciding to kick it out but now I am very satisfied with this little amp.

Is the CODE™412 4x12-inch Angled Electric Guitar Speaker Extension Cabinet discontinued? If so, then why? I did purchased one 2 years ago.

My online dealer no longer has it listed; instead, they have listed, the CODE™212 2x12-inch Angled Electric Guitar Speaker Extension Cabinet ― which I do plan on buying ― however, I still would like to purchase another CODE™412.

I did this binaural test on YouTube and at the same volume, nothing changed volume-wise, the right speaker was quieter than the left. I just got this amp like a week ago and I figured something was off about it. What should I do? Send it back? I got it through amazon and I think the return policy is still available. But I would like another one, just not kinda broken. I can make a video if need be.

This is my amp: Marshall Code 100W 2x12 Digital Combo Amp

I have a 2012 DSL40C.  If I use a 16 Ohm extenstion cab, can I plug that into one of the 8 OHM outputs, and then move the cord for the internal 16 ohm speaker to the other 8 ohm output, basically turning this into a 12 x 3 speaker configuration? Will the amp be able to power that many speakers? 

So I've been thinking about buying a Celestion F12-X200 speaker for my code 50 and was wondering it this would work. The reason I need to know this is because even though I know you can use an 8ohm speaker on a 4ohm tube amp, I'm not sure about a digital amp. Could anyone tell me if this is possible.

where are you suposed to register your warranty for my code 212 speaker cab.

I'm using USB on my Mac and the Mac sees the Code and allows me to set the speaker to it.
When I pull up a Youtube video and start it the video will play for about 5 seconds and then halts.
It's almost like something else is intercepting it. It basically locks up and I have to close the browser.

Same issue when using the Code 25 as input device on Mac for Garage Band. It recognizes it but when I record
upon playback the sounds are scratchy and unusable

This Code 25 works on my Windows Machine both ways as Input and Output device flawlessly

I have installed the latest firmware so that is not the issue.

Any ideas on what it might be causing the problem on the Mac?

--Pat Brown