Looking for a great priest preset. Thanks
Looking for a great priest preset. Thanks
I recently purchased a CODE 25 and love it. In the Gateway app I see a different list of presets when connected via Bluetooth versus not. Any suggestions of how to correct?
When not connected I can see presets like Purple Plexi and Sweet Jubilee. Would like to check them out.
Thank you.
Hi I have a CODE 100H head/cab and a CODE 100 combo both with the latest firmware re-installed from Marshall and both have this issue, i.e. the amp very oftenn completely freezes when I save a preset.
Steps to reproduce:
- Modify any patch on the front panel
- Save
- 50% of the times the amp seems to freeze. The preset is saved but you can no longer change preset and there is no sound coming out.
The same happens if you modify a patch from the iOS app via bluetooth and then save it from there.
It's REALLY frustrating and I can't believe I didn't find anything on this forum under the "crash on save" keywords. Seeing it happens on both of my CODE units it much be a software bug, I don't think it has anything to do with my units.
Anyone else has seen this problem?
Thanks!
Hey guys,
A couple questions. I am trying to love this amp--it is compact, seems to have plenty of control, and I like how easily it connects to my computer. The problem I have is similar to others: I do not need a ton of volume and a lot of the sounds seem a bit muddy. I've tried turning the preset volume way down and use Master and this works to an extent.
Some questions:
1) I noticed people talking about putting a Celestion G10 Greenback in it. I'm planning on trying this. I was going to go with 8ohm to save some volume but will the frequency range be a problem? It seems like stock is a full range generic speaker likely so it can be more neutral for amp modeling and for music playback. I do not need to play music through it..... and
2) How bad will this mess up the presets? Am I basically throwing presets out if I change the speaker?
3) Has anyone modified the back of the amp to open it up? I heard some asking about this and not sure if it is worth it.
Thanks, looks like others have been curious but have not heard anyone report in on actually doing this. Love some feedback!!
*****UPDATE : PROBLEM SOLVED. OR MORE CORRECTLY, NO PROBLEM TO BEGIN WITH. APPARENTLY THIS IS NORMAL AS ALL OF THE PRESETS HAVE BEEN SAVED TO MY AMP. NO REPLIES NECESSARY. THANKS! ****
Hello all,
I'm a new Code 50 owner and am just getting started. I bought mine used from Guitar Center so I don't have the manual at hand and am running into an issue. I have added a ton of user created presets to my library on the gateway page, and synched them to my android app. When the app is connected to the amp I can see the presets when in gateway mode (blue dials).
Here's the problem I'm having: When I try to save the preset to the amp, I open the preset in the library, click on the arrow to the right, and put an x in the amp box. When I click save however, the amp box unchecks and I'm back where I started.
I'm not sure if this is a glitch or I'm missing a step somewhere. Can anyone help me out?
Thanks much!
Mitch
I know how to relocate the presets but what happens to preset I overwritten? How can i just move the presets in an order I desire without losinbg any presets?
What would be the correct way to connect the multi-effects (POD HD 500x) to the amplifier (CODE 50)? I would like to use the multi-effect amplifier emulator in some presets. please
Hi all,
I write small desktop app for CODE25.
Everything working except uploading whole preset into CODE.
This is sysex message which i sending into Amplifier to change active preset
sysex data=(0,33,21,127,127,127,114,2,0,68,101,97,116,104,32,83,121,109,98,111,108,105,99,32,50,32,32,0,75,55,20,40,50,1,1,0,25,50,25,1,12,30,0,0,50,50,0,50,0,0,0,0,50,50,50,1,2,35,25,30,20,1,0,75,75,1,7,1,2,3,4) time=0
what is wrong ?
thanks.
I am not able to transfer presets from Mac to Code 50. The display below preset shows code not available though usb is connected
Hi
I purchased a Marshall Code 100H in April 2019.
It was replaced under warranty last week by the retailer as it had developed a constant electronic beeping sound.
I received the new head and right out the box it was much improved. I decided to get to grips with loading up my presets and patches so began by carrying out the latest firmware update as advised by Marshall, alas, the electronic beeping sound has returned.
It is constant and present with or without a guitar plugged in, elevates with master volume, cannot be fixed with a noise gate, the amp has been plugged in several different venues and the noise persists and it was not auidable before updating to firmware V1.44. Jul 2019.
Is there a means of rolling back the firmware or is there a known fix for this issue, it doesn't seem fair the retailer has to replace another amp which was fine until update was applied. Any advice would be much appreciated.
Thanks
hello, sorry for my approximate english, i'm french .. I bought this little amp (code25). rather nice but I see a PB rather boring ..... if I use the quiet amp, in "standalone" mode without launching the app .... I am looking for a preset with the wheel, I play and hack the settings .... I finally my sound, cool , so I launch the gateway app to have a view of all parameters and can simply record ... and patrata, by launching the app, the amp starts on the preset number 1 and I lose all my settings from my preset precede ... rather boring. there is a solution so we can launch the app (after launching the amp, we do not necessarily launch the app all the time) without having a change of preset? thank you
I have a CODE 100h + CODE412 and I love them !!!!
I use a pedal board with different effects and was thinking of adding a looper / switcher (Boss ES-5 or MUSICOM LAB EFX LE).
I would like to know if with the looper I have listed I can change presets to CODE100H via midi. Do I need a USB / MIDI interface? Thanks
Is there any option to change volume with the PEDL 90008 ?
I know that it is possible to change volume by editing different presets.
But I want to know if there is a way to change the volume with other methods.
Would be great if there were an FX to change volume in switch mode.
Has anyone any settings for Rory Gallagher or Derek Trucks Slide?
I was having difficulty syncing my gateway app to my Marshall.com to add downloaded presets to my library. On the forums Marshal suggested doing a factory reset by holding the amp button down while restarting the amp.
I did that. Now when I try to Bluetooth connect the gateway app and the amp I get this an error that says "connection rejected. You may only control amps you are already connected to for audio output".
I have restarted the amp and phone but I keep getting the same error message.
please advise on both this current problem as well as how to sync my gateway so that the downloaded presets get added to my gateway library.
List of factory presets for CODE 100H head. From 2019, the presets are different than combo models. Rig info: the CODE 100H head and 4X12 cabinet.
Can CODE 50 sync user presets by iPhone app ?
I know the way by mac(chrome).
Hello, I have a code 100H and using Windows 10 on the P.C.. Can I download my personal presets to the gateway library for safekeeping? If so, how. Thank you.
Is my first marshall amp and i have a doubt, i don´t know how to sort my presets, for example if i wanna move the number 10 to the place 2 only its copy and delete the preset from that place and then i have the same preset in two places, but i wanna only move the preset. thanks