Hi there ,
I recently bought a DSL1CR and see that the one speaker output states 1x16 ohms. 
I am aware it can be run without a speaker for silent listening through the emulated output. 
Can I connect my 8 ohm 1923 external 2 -12 cabinet to the DSL1's 16 ohm speaker output and run it safely? 
Thanks,
Russ

bonjour

je recherche une preconfiguration de Mission Impossible Theme de Lalo Schiffrin

pouvez vous m'aider?

I've been holding off for the next-gen Kilburn for the last 2 years, but I'm obviously getting impatient since the last Kilburn was launched some 5 years ago and there's not even a speck of news out there about the next-gen! :((

Now that Middleton has come out, I'm guessing that it is the replacement for Kilburn.  Shall i go ahead with a Sonos, or is there still any hope for Kilburn III?

The Gain and Mid knobs on my Code 25 are unable to reach 0 or 10 despite being turned all the way down and up; the gain's range is 3.7-8.1 and the mids are 1.9-6.1. Resets and reinstalling firmware have yielded no results.

Have enjoyed code 25 for a few years.  Suddenly the amp has started to drop output.  Happens after a few minutes of playing.  All lights on, no noisy pots or anything.  Just no output.  I can switch it off and back on and output restores.  But after a short time, same thing.  No output, suddenly cuts out.  Nothing.  Anyone seen this?

After selecting a Preset, and after playing a song when I go back to the Gateway app I see a message saying, "Amp Disconnected, Connection with your CODE amp has been lost. Please check your amp and try to connect again." When I select "OK" it reconnects then I can select a preset. This seems like a new"bug" since the Gateway app has been updated to the current version. My iPhone is on a stand close to my CODE 50 the entire time. (about 1 or 2 feet at most).

Please advise. Thanks!

iPhone 13 Pro, iOS 16.4.1

Firmware: 01 Sep 2022 - v1.47

CODE 50

i have a question is this a legit one that I bought.??

Dear Marshall....

I'm a total fan and player of the Marshall Code Amp. In my opinion the best amp in the world ( The Marshall Code) that is...

This amp has everything I need to gig.. record..  and just jam... in one easy to carry unit..  But... I have a problem... my USB plug on my Marshall Code 100w Head is broken will not plug into my cord because the USB port was damaged by me. The prongs in the head were bent backwards and are broken...

IS THERE ANY WAY I CAN GET THIS AWESOME AMP FIXED... PLEASE 🙏 

THANKS.. Allen Perez 

allenperez911@yahoo.com 

Hello,

I'm going to replace the power tubes with a new kit of 4 matched EL34 and I would like to know what is the BIAS setting recomended by Marshal in terms of how much mV we should adjust on the reading of the Test Pins  CON5. I found someware that is 90mV per side, but also other different info (some guy said 76mV after consultation with a techician). Please could uoy kindly advice?

thanks!

I have  Marshall Code 100 and it is ususable because the presets keep changing by themselves. Is anyone else facing this issue? 

Why i couldn't can connect my Headphones with my Phone on Bluetooth??

I have the Major IV Headphone andta Phone from Xiaomi M4Pro

Bonjour,

Comment faire pour supprimer un preset de l'appli Marshall Gateway( code25).

Merci

My chassis says PWB980801A and after being told to junk this amp I saw an article that said burnt components definately harm other parts.  The burned parts on my circuit board are 1.) ZD3, 2.)another ZD3, 3.)R111&270J DAEDO, 4.)R112&330J DAEDO, 5.)a blue resistor with 2 black and 2 red rings on it, 6.)desoldered TR10, TR15, TR6 & TR9.  When I lived at 522 Rhea Street in Long Beach, CA  someone I was living with asked me to take my guitar and amp outside and play.  I did but a policeman said he would have me arrested is I didn't go back inside.  I would like to keep this amp but it is kind of loud for the one room where I live.  All the repairmen I've found have refused to fix it.  I told ASCAP about VanHalen and got $5,000.00 and bought this amp in 1984.       

I own a MARSHALL JCM800 LEAD 50W 4210 (1X12", 2 CHANNELS, REVERB), with many years of use, I bought it new about 36-37 years ago!!!, and now the reverberation has started to fail, if I go up the REVERB potentiometer makes a lot of noise and when it goes past 1/4 of a turn feedback appears, I don't know if the problem is electronic, or if the reverberation module has broken, I think it has an ACCUTRONIX or a HAMOND (I haven't disassembled it) Can the module be repaired or does it have to be changed directly? What brand and models is it? Where can I get one? If the same model is no longer manufactured, what would be the equivalent model?

Best regards

Here's an interesting thing. User Tomáš Nekovář, stole my Octafuzz preset and put it up as his own. Even complete with my Youtube link and soundcloud demo.

Seen it all now,

Oh well it was put up to share anyway, so enjoy MY patch everyone.

Why boost pedal doesn't work at Marshall code 50? I have plugged the electric guitar into volume pedal and the volume pedal into guitar input on amp, but haven't had no boost effect! Will volume pedal work? I'd like to boost my solos, anyone faced this problem?

I'm finding it hard to register my brand new Origin50C. Can't find the serial number it's covered by a sticker on the box. No where on the amp itself can I find the serial number

need Metallica tones for "Black" and "Justice" album

I'm restoring a couple Marshall speaker cabinets, maybe from the 90's. Two of the above speakers are not working. 

Thanks,

Paul Haggett