Why i couldn't can connect my Headphones with my Phone on Bluetooth??

I have the Major IV Headphone andta Phone from Xiaomi M4Pro

Bonjour,

Comment faire pour supprimer un preset de l'appli Marshall Gateway( code25).

Merci

My chassis says PWB980801A and after being told to junk this amp I saw an article that said burnt components definately harm other parts.  The burned parts on my circuit board are 1.) ZD3, 2.)another ZD3, 3.)R111&270J DAEDO, 4.)R112&330J DAEDO, 5.)a blue resistor with 2 black and 2 red rings on it, 6.)desoldered TR10, TR15, TR6 & TR9.  When I lived at 522 Rhea Street in Long Beach, CA  someone I was living with asked me to take my guitar and amp outside and play.  I did but a policeman said he would have me arrested is I didn't go back inside.  I would like to keep this amp but it is kind of loud for the one room where I live.  All the repairmen I've found have refused to fix it.  I told ASCAP about VanHalen and got $5,000.00 and bought this amp in 1984.       

I own a MARSHALL JCM800 LEAD 50W 4210 (1X12", 2 CHANNELS, REVERB), with many years of use, I bought it new about 36-37 years ago!!!, and now the reverberation has started to fail, if I go up the REVERB potentiometer makes a lot of noise and when it goes past 1/4 of a turn feedback appears, I don't know if the problem is electronic, or if the reverberation module has broken, I think it has an ACCUTRONIX or a HAMOND (I haven't disassembled it) Can the module be repaired or does it have to be changed directly? What brand and models is it? Where can I get one? If the same model is no longer manufactured, what would be the equivalent model?

Best regards

Here's an interesting thing. User Tomáš Nekovář, stole my Octafuzz preset and put it up as his own. Even complete with my Youtube link and soundcloud demo.

Seen it all now,

Oh well it was put up to share anyway, so enjoy MY patch everyone.

Why boost pedal doesn't work at Marshall code 50? I have plugged the electric guitar into volume pedal and the volume pedal into guitar input on amp, but haven't had no boost effect! Will volume pedal work? I'd like to boost my solos, anyone faced this problem?

I'm finding it hard to register my brand new Origin50C. Can't find the serial number it's covered by a sticker on the box. No where on the amp itself can I find the serial number

need Metallica tones for "Black" and "Justice" album

I'm restoring a couple Marshall speaker cabinets, maybe from the 90's. Two of the above speakers are not working. 

Thanks,

Paul Haggett

Hi everyone, 

I bought the new DSP module and plugged it into my Code 25. Everything seemed to be fine,

However, when I turned it on the code went into bootloader mode and said "chk usb". I inserted a cable and my PC saw it saying "connected". Still neither the marshall site not the PC application provide with possibility to update. The site shows no information and the PC app says that the last firmware version is installed and cannot reinstall it. When press reinstall button nothing happens.

I tried Mac, MS Edge and other browsers, nothing works

Any ideas?  

Hi all,

I bought my Code 100 in Australia, where the voltage is 220 V and the amp only works with 50Hz as indicated on the back of it (unlike many other products that work with both 50/60 Hz).

Now that I have moved to the US, I am not able to use it anymore! I purchased a 110 v to 220 v step up transformer, which is fine, but cannot change the frequency from US's 60Hz to 50Hz to safely turn on the amp!

Frequency converters are like $1000 or so, so definitely don't worth it!

Is it possible to request Marshall's company itself to change the power board or something to make it work normally in the US without transformers, converters, etc.?

Would it be safe to just use the step up tarnsformer and ignore the frequency (Hz) difference?

Really appreciate any suggestions or guidance,

Thank you in advance!

I have a Marshall DSL40CR. I have checked the amps bias 5 days in a row and every day it's lower than what I have set it to. I was told bias in 40 watt mode should be around 35. When I set it to that on the first day and played...it sounded excellent. I put it in standby and powered off. The next day I turned it on with standby on and waited around 5-10 minutes. When I went to play it sounded really off. So I decided to check the bias and 1 tube was at 30 and the other 33. I reset both to 35. 

The next day after that I had to set it yet again because it was 30/31. The next day after that the same thing lol. 

Would this be an Amp issue or Tube issue? Once I set the tubes to 35...plays and sounds great the entire time I play. However, if I shut the amp off and come back later the amp bias is always lower.

Can the foot switch be programmed to not remember settings on each channel, only the basic pre loaded ones? Meaninig that if it remembers that I had reverb on channel 2 of the clean sound, I dont want it to turn reverb on next time I cycle through to that channel. 

How can I reinstall all the 100 factory presets (and overwrite all my selfmade presets) ???

I recently purchased a Code 25 and uploaded some presets to it. When I first select the preset it sounds great, but if I go to another one for a little bit and cycle back, the sound is completely different. What could cause this? The only thing I'll change when playing is the master volume. It typically gets very boxy with a lot of bass and lose mid/treble sound. I have to turn it off then on to get it back.

Hi,

A few months ago (Oct 2022), i buy in Reverb a Marshall Valvestate Bi Chorus 8280 and when i turn on, all feels ok, but one day i note only work one speaker. I change the cables and the other speaker are fine and i think the problem was in the output jack.

Finally, i found a tech who tell me he can check it and repair. When the amp is ready to go, i pay and check it in their local store and i notice a weak sound, but i thinked it was the room. The L and R speakers out works now but the problem comes when i push the chorus and the volume rise and have more body.

The guy tell me is because the amp only works in stereo when chorus is on (great sound and body), and in mono (sound lack and low volumen) when put off, but i don't believe it and that's why I'm looking for an answer here.

P.D. When i receive the amp, the first thing i do, is change the valve, so this is not the problem. If i disconected one speaker (L or R), sounds good and the chorus doesn´t affect the tone.

Please help me.

Hi Everyone,

I bought a Marshall Studio Vintage Head in US where we have 110V voltage and 60Hz frequency. If I want to use that amp in Italy, where the voltage is 220V and 50Hz frequency, is it okay if I only change the currently mounted (US-rated) fuse? Or do I need to get a transformer? I am not sure if the amp is only rated for 110V / 60Hz...I like to think that it was built for a range of V and Hz that works for Italy / Europe as well, being made in UK.

If the fuse is the only mod I have to do, then I can just use a campatible power cord to plug it in?

Forgive my ignorance, and thanks in advance.

Antonello

how to add a GRAMS preset?

After many many many failed attempts to update firmware it finally showed successful on the update page but now the screen permanently shows do not switch off or usb not connected and is unusable, no buttons work ,completely frozen.