Ever since I connected a USB cable between my CODE 50 and set up this account I cannot get sound to come out of the speakers. My amp is all but dead.  HOW do I reboot or reset my amp to make sound come out of the speakers when I jack my guitar into it; turn the unit on; slowly raise the Volume GAIN and Master volume and hope to play something?

Does anyone know?  Thank you for your time.

Got my amp, Code 100 combo and loving it, lucky to have a present of the new PEDL CODE Footswitch.

Being a bit of a noob to this new amp technology, I have managed to save a  preset to the pedal, but no thanks to the instructional video mind you, which misses out the essential part that you are meant to press store on the amp and press the location on the pedal at the same time. There I was pressing the footswitch like it says in the video then trying to store. Very ambiguous instructions there, not clear at all.

However, one question is, once I turn off my amp, are the settings on the footswitch wiped out or are they stored until I want to delete them?

Also, it appears that I can only store to the pedal from the amp. So what if I'm using the amp in 'blue' mode from a hand held device?

 That doesn't seem to work for me (using my preset from my handheld device and storing to the pedal that is) as it keep defaulting to an Amercian preset.

I may be doing something wrong, therefore I thought I'd ask the question, rather than just pull what little hair I have left out in frustration.

What are the limitations on the Code pedal? The documentation is woefully inadequote IMHO. The suppport video being just as poor.

I know the issue, it's software designed by software developers, with no end user experience being considered as opposed to using a UX team during development.

We either need more indepth clear and concise instructions, or a new video showing a detailed example how to save a preset (not just a voice over while looking at flashing LED's) and whether we can save, not only from the amp, but save a preset from the handheld device and store them for later use.

Sorry if the above is a bit of a moan, but if nobody moaned nothing would be done.

If you could answer my points above, that would be helpful.

Thanks

C.

Hi everyone!

Recently I bought Marshall CODE 25 and it's a great amp but I have one little problem with it.

There is a problem with MASTER potentiometer. I noticed that when I set it between 0-0.99 it is very very quiet but when I set it about 1.0 it becomes very loud. And in the effect it is very hard to play at "bedroom" volume levels. I must say that I'm disappointed - I had Yamaha THR 10 previously and it could play very well at every volume and it could play very quiet.

So to sum it up, is this some general issue with all CODE amps or something is broken in mine? Maybe master potentiometer needs repair?

I just bought my code 50 yesterday. The master volume is a real problem, I may have to return it just because of that. We can adjust the volume, but the second you change a preset it goes way too loud again. Even if I were to modify each of the 100 presets manually (which I am not in the mood to do), when the next firmware update happens those presets will be overwritten with the factory reset so back to square one.

Marshall, can you please give us a timeline for this? I have 30 days to return this thing to the store, I need an answer because I do not plan on living with this issue forever, maybe I will swap if for a Fender or Line6 or something with quicker response time from the manufacturer if need be...  quite frustrated and only used the product for 30 minutes. 

Hi,

I own a DSL20HR amp and I'd like to connect two 1x12 speaker cabinets to the amp simultaneously. Both cabinets are Marshall 1912 cabinets (1x12", 8ohm speaker). There are three speaker cabinet output jack sockets in DSL20HR:

one 1 x 16 OHM socket to connect a single 16ohm speaker cabinet, and

two 1x16 OHM sockets to connect two 16ohm speaker cabinets simultaneously or to connect a single 8 Ohm speaker cabinet to either one of these sockets.

How do I connect two 8ohm cabinets to this amp? I'd like to connect these cabs in series to have 16ohms in result, but the cabs don't have sockets for connecting them in series. There is only one input in 1912 cab. And if I find a device to connect this two amps in series, do I then connect the first cab's input cable to the DSL20HRs single 1x16 OHM input (the first input option)? Is this safe? The manual doesn't say anything about connecting cabinets in series.

Thank you! The new amp is great btw!

Ok, the buzz, fuzz I and others noticed (Its Real). First before you ask I tried the cable and the guitar on my Crate Amp. The notes ring like a bell No fuzz or Buzz.

So that eleminats my guitar and cable.  I notice if I use eather the Acustic or Natural Pre Amps on my Code -50 the BUZZ / Fuzz dissipears. So I assume its not a hardware issue with the Code 50. I think its a software issue. Is it possiable to fix and down load  new Pre Amp Modelse to fix the problem? 

I would love to get this fixed! Its annoying!

hello,

Bluetooth connection is not very good in my opinion.

Bleutooth signal code 25 is ok, samsung s8 detects it alright.

But when i use the gateway android app it doesn't connect altough it shows in app as detected.

Is there a patch upcomming for the amp code series?

Greetings

Why does my code 50 amp cut out? Also, has loud crackeling sound when it's working. Sounds like a blown speaker but it's not. The master volume is only turned up 1/4 of the way and it's loud. Problems still remains even at lower volume. slight delay on the footswitch also when changing from one preset to another. Frustrated in Detroit.

I have been trying to connect to my PC for hours now. I have the latest version of chrome. And allowed the midi. Also I did the windows RT. still no connection Any help would be greatly appreciated

Hello guys! I recently updated my marshall code 25 firmware to version 1.41. However, when I turn it on it says on the screen "v 1.11" why?

I just updated the firmware and now I can't connect .

is it the update that is the problem?

Dear all.

In my code 50 fw 1.41, when I play, I  hear noises eg preset 02,03.04,06,07 ... 93. Is it similar to you or do you have a clear sound (no noise)? My guitar Gibson les paul tribiute 2017 and I use cable Fender FG10.

The best Regards

Jaca

I can send a sample to interested persons

Hello!

I’ve just bought a Code 25 with footswitch and have just started to look at the presets.  As far as I can see each amp sound corresponds to a number - for example Bluesbreaker Reverb is assigned to #44. Is there a way or re-assigning this e.g. to #1 ? I’d like to be able access some of the presets easily rather than having to scroll through all of the numbers.

Apologies if this has  already been asked on the forum

Many thanks

Robin

This site is not secure

This might mean that someone’s trying to fool you or steal any info you send to the server. You should close this site immediately.

Hi All,

As it was mentioned on this forum connecting additional looper pedal isn't possible in a direct way, bacause there is no FX in and out. 

I'm wondering If anyone has experience in building FX Loop using AUX In and Headphones Out in Marshall CODE 25/50 amp?

Can it work? If so, is this a good option?

Mike

How can I get the Marshall Gateway App to install on my ATT-ZTE Z971 Android version 7.1.1 cell phone ?

Google Play says my phone not supported. There are no warnings of this nature when buying the "CODE 50".

Has anyone tried using the code 50 with wireless headphones?

I have a pair of seinheiser 120ii, and I just get this weird "feedback" sound when I plug them in.

The headphones work fine on all my other devices, but not with this amp.

I tried 2 other sets of wired headphones, and they seem to work fine with the amp.

Is this a known problem, and is there something I can do to fix it?

Thanks

Gerbrand

Hi guys,

I've bought to my girlfriend for Christmas wireless headphones Marshall Major II Bluetooth. I can not connect them by bluetooth with any PC (Windows 10). Any of my PC's with Win 10 and BT technology won't see these headphones, although my android smartphone will see them. Is there any trick how to connect those headphones to PC? Is it even possible? I'm not talking about connection via a cable of course.

Thx for answer!

L.

Hello

In the manual is told not to use the Code 100 head without a speaker? Why?

I think it's not a valve amp.

Martin

One of my fave bands is The Tea Party, and they use a LOT of different tunings.  However, the tuner in the app only has specific tunings saved.  Is there a way to save other alternate tunings to Gateway?