Questions
Showing results 3461 to 3480 of 3523
37

votes

3

answers

2.7k

views

Hi, is it possible to see the Amps I have registered on my profile?

Cheers, Andy

asked 29 Jun 2016 at 06:12 PM

X X (37)
0

votes

1

answer

1.1k

views

Just purchased a new Code 25 amp and about every 30 seconds or so it looses its bluetooth connection and I have to go back to the connection page to reconnect it. Often after reconnecting it looses connection again before I can even back out of the connection page and make any changes to the amp. This is very frustrating. Ive checked for new firmware updates and there are none. I have seen others on forums complaining about the same issue. Is there a fix?

asked 29 Jun 2016 at 03:37 PM

Odell Robinson
6

votes

8

answers

2.3k

views

I am running Windows 10 on a compatible laptop and get an error message when I try to run the Marshall update utility software. It occurs after a "verifying application requirements" window pops up. The error starts with "An unexpected error just occurred. Cannot create instance of main window"?

Any advice?

Steve

 

asked 29 Jun 2016 at 07:44 AM

Steve Sweeney (6)
0

votes

1

answer

922

views

When I save a preset in the app the preset will multiply as in there will be more than 1 of that location and none can be used.  Is there any way to fix this? I tried deleting and redownloading the app but it happened again. Thanks!

 

 

asked 28 Jun 2016 at 10:32 PM

Raphael Hanna
0

votes

1

answer

926

views

i registered my amp, but it doesn't show on my profile page, have i done something wrong !

 

asked 28 Jun 2016 at 10:22 PM

J D
0

votes

1

answer

889

views

Hi, I recently purchased a brand new Marshall jvm410c amp.

I have a knob that is defective.  It is crushed on the golden rim.  It was given to me from the factory this way.

Will you please send an oem direct replacement knob for me?

Juan Ramirez

asked 28 Jun 2016 at 09:48 PM

Juan Ramirez
0

votes

1

answer

805

views

I need to clean my master volume pod but these dont look like your avrege pods. So really I'm asking if it would be ok?

asked 28 Jun 2016 at 07:29 AM

Jayson Seals
0

votes

1

answer

1k

views

hi, i registered my code 25 amp, but cant find anywhere in my profile .....  ie: my marshall (cloud) as to all my registered amps ?

asked 27 Jun 2016 at 11:49 PM

J D
0

votes

2

answers

884

views

I have a '77 jmp 100,currently through a 4x12,am looking at downsizing due to portability issues,but am loathe to part with this awesome amp that has been with me since the late 80s,so am considering using with a 2x12,any advice,regarding resistance values,suitable cabs,would be appreciated.

asked 27 Jun 2016 at 09:17 PM

Damian Clayton
0

votes

1

answer

918

views

when can you sevice my 100 watt lead head .it packed up on a gig saturday 

asked 27 Jun 2016 at 07:49 PM

chris waine
3

votes

3

answers

2.5k

views

HI just got  a new (3 days old) JVM 205C and played it a couple of times then when I went to turn it on again it will not make a sound!

It starts and all the tubes light up but when you turn off the standby nothing happens and no sound at all comes out, not a click as if the standby swith is doing nothing.

I did read the manual about the FX loop button muting the amp without effects plugged in but I have tried everything I can think of so far, guitars, leads other power sockets but no go!

Anybody have any ideas???

Thanks

Mark

asked 27 Jun 2016 at 12:07 PM

Mark Pianca (3)
4

votes

3

answers

6.6k

views

It seemed to have installed CODE Audio interface, because I can see it is my Devices & Printers (Windows 8.1) as a composite device with a 2013 Microsoft driver installed. But it does not show up in my DAW at all. 

Where is the driver and than in particular the ASIO driver for this????

It is connected, because when I use the WSAPI (Windows Shared API) is can see the SPEAKERS from code and play audio through there (horrible quality though). But not the input. Without that, this device has not much value for me. 

Thanks for your help,

James

asked 27 Jun 2016 at 12:12 AM

James Clent (4)
17

votes

1

answer

2k

views

I registered my amp on My Marshall but I don"t see where it's listed. After I registered the amp I don't see it listed as part of my profile. There should be a "registered amp" tab so that I can access the serial number if I need it. Thanks.

asked 25 Jun 2016 at 05:21 PM

William Fleitz (17)
0

votes

1

answer

814

views

I have looked high and low for a cover for my AS50D. The only luck I had was one place said they had them on backorder and I never heard back fom them. Any suggestions how I can get one - soon?

asked 25 Jun 2016 at 04:33 PM

Joe wilkie
0

votes

1

answer

1.2k

views

I do not know what year my TSL combo amp is  but it is an older model. Will the foot switch for new TSL 60 or 100 watt work  with my  JCM2000-60W  TSL 602 combo and if so where can I purchase a circuit board for the foot switch, the channel switches are bad but the reverb and the effect switches seem to be working OK they are turning on the indicator light on the pedal, but will not turn off the reverb and effects. Please help me with this if the circuit board needs replaced 

asked 25 Jun 2016 at 01:47 AM

Ronald Mullins
0

votes

1

answer

1k

views

is there a downloadable manual in Spanish language available for the CODE 25?

asked 24 Jun 2016 at 09:34 AM

Mario Cristobal
0

votes

1

answer

1.1k

views

Any diagrams or recommendations for setting up the effects loop on a dsl40c?

asked 23 Jun 2016 at 12:54 AM

Henry Dahm
0

votes

1

answer

902

views

Hi everyone,

Do you know in wich year does the jcm800 4104 Vertical imput as been producted..?

 

Thank you

asked 22 Jun 2016 at 10:11 AM

Filippo Piccagli
0

votes

1

answer

1.1k

views

how do I find original replacement parts such as ohm pin for pin socket/input/output jacks/small logo for amp head?

asked 22 Jun 2016 at 01:58 AM

Stephen M. Stephenson
0

votes

1

answer

1.1k

views

My amp is a 30mgfx and when I turn it on I need to move the gain to make it sound good and the power of the volume is not the same as when I bought it, what should I do?

asked 21 Jun 2016 at 07:45 PM

Esteban Signoret
Showing results 3461 to 3480 of 3523
Loading - please wait...