Comprei um Code 50, toquei poucas vezes com ele e sempre com o volume baixo. Ontem fui ensaiar com banda e aumentei o volume, várias vezes o amplificador ficou mudo e o visor continuou ligado, quando eu desligava o amplificador e ligava novamente o som voltava. Hoje cheguei em casa e toquei com o volume de ensaio, novamente o amplificador fez a mesma coisa.
If I purcase the marshall code footswitch and plug it into the f/c input on my code 50 do I connect the looper and the drum machine into plugged into the input on the left. Would this stop the drums from getting the effects on the effects on the guitar
I just bought 2 Marshall CODE25 amplifiers, hoping I would be able to connect them through bluetooth together or atleast by wire. I don’t know how to, or if it’s even possible. I want to use the amps as speakers too so an ABY pedal doesn’t really help. I tried to connect them by MP3 to Headphone ports via 3.5mm jack, but the amp originally playing music stops and sound comes only through the second one, but louder than normal. I want both of them to play at the same time. Please help! Thanks! 😃
Can anyone tell me which casters to get for my 2x12 extension cabinet I use with my code 100 H, thanks.
I don't know how to use the playback tab on the gateway app .
Could you help me please ?
I'm using USB on my Mac and the Mac sees the Code and allows me to set the speaker to it.
When I pull up a Youtube video and start it the video will play for about 5 seconds and then halts.
It's almost like something else is intercepting it. It basically locks up and I have to close the browser.
Same issue when using the Code 25 as input device on Mac for Garage Band. It recognizes it but when I record
upon playback the sounds are scratchy and unusable
This Code 25 works on my Windows Machine both ways as Input and Output device flawlessly
I have installed the latest firmware so that is not the issue.
Any ideas on what it might be causing the problem on the Mac?
I really need the above to repair my Marshall MG30CFX guitar amp. Can the forumers point me to the right place to download it?
Or is the numbering of the presets ... haphazard?
Hello.I have a big problem with my amp.When I increase the volume level,from my cabinet sometimes come out very loud and terrible sound.It is just like the amp will blow my cabinet 2x12 120W.Ultra gain section - Volume at 5 and more,Gain at 5).Is this bad tube,or something problem with amp?Sorry for my english!
Hi, I have a question about the Studio Series SV20H and SC20H DI OUT
The user manual say the DI OUT have emulation, but in both of your official product video on youtube (for SC20H and SV20H), Steve say the DI OUT is NOT emulated so it's perfect to use with our own Impulse response...
So who is right, the user manual or Marshall official product video?
https://www.youtube.com/watch?v=GvuQPnqMktc at 2min43 he talk about the DI OUT and he say same for the video for the SC20H
Thanks in advance!
bonjour, j' ai une tete marshall code 100 et je voudrais m enregistrer maisje suis nul en informatique. j' ai relié ma tete marshall à mon pc en USB, mais ensuite, que faire ? Je dois télécharger un logiciel DAW ? ( gratuit si possible ), et après, quelles manoeuvres à faire ?
Si quelqu un peut m aider ce serai génial, des explications simples et très précises svp...Merci d' avance.
I'm a beginner. I've experiemented with all the presets of my CODE50. It's an amazing amp/speaker combo. However, I would like to have a better understanding of what the switch and 4 knobs do on my Epiphone Les Paul, apart from all the amazing things that the CODE50 can do. This would seem to require that I set the CODE50 to work as a "pure amplifier," solely increasing the volume of the guitar output, without adding any effects to modify/model its output. Can I achieve this by doing the following using the iPhone app?
Turn to Pedal 1 preset (and not use a pedal)
Keep Pre-Amp at Natural
Turn Power-Amp and Cabinet off
Turn all FX off
I eed. To know what order would I place my effects peddles so I can play a clean loop and then put a distorted loop over it.
I just completed a tour and on the last night, mid-set, my Code 50 suddenly turned off and wouldn't turn on again.
Got it home and I still won't turn on. No lights, no nothing.
Anyone else had this problem?
It was totally fine and really sounded great for the whole UK tour and then the whole Europe tour, apart from the last show.
Any thoughts much appreciated.
Toby (Art Brut)
Is it possible to put a loop function on footswitch in a firmware update? I know I could buy a looper pedal, but I bought a digital modeller so I didn't have to go down that road.
looking for model of footswitch for JCM2000 DSL
Last update 10th Oct 2017 v1.41 surely there has been something to update Marshall Team such as bug fixes and new presets since 18 months ago, or have you just forgotten us after having all our well earned money!
I'm currently looking at getting either the Marshall DSL1H or DSL20H amp head. I know that they both have emulated out's that can be used with headphones, but what I'd like clarified for me is how this would work exactly. I'm not going to be buying a cab for it right away, but would like to be able to still use all the knobs on the amp to sculpt te tones I want and to also control volume levels. Is this something that I can achieve without a cab connected to it? If I need a cab connected to it can I just connect it to a load box?
I just received my brand new CODE100H Head with matching CODE412 Cab from Sweetwater, but I cannot get any sound from the amp.
Turning everything to 10 including master volume sounds like it’s on .005 watts or something like that. Extremely faint. Should be rattling the house, but it’s not.
Tested the cab with another amp and it’s fine. Tested the amp with another cab and got nothing. When I plug it into my headphones, it’s faint but can hear it.
Hello, I've had my code 50 for about a year and a half. A few months ago I noticed my amp would stop projecting any noise a few seconds after i would turn on the amp, i found it weird because when i play with my headphones plugged in it works fine but when the signal passes through the speaker it stops making any noise, just completely shuts off.
It isnt the cables or the guitar as I've tried multiple on the same amp, so I imagine it is a problem with the speaker, anything I can do?