hi everyone , i got the marshall code 50 , i had a chance to get it connected to the laptop using win10 , after some days , it stopped getting recoginsed by the computer , is there anyone who could reach to a solution to this issue , it really makes you crazy ,
i've tried with many other usb cables and changed ports
Actually I'm totaly not interested in bluetooth connection, but of course I understand that it might be an essential prolem for some people...
But there are some other problems I'd like you to find good solution for.
1. Master volume. From 0 to 10% there is almost no sound, over 10% it becomes very loud.
2. Decreasing sound level with Volume pot results in decreasing USB signal level - not acceptable for players using USB output for recording in DAW software. It would be nice if for clean preamp gain at 2 and volume at 3 give recording level about -6 dB, now it is about -36 dB...
Best regards, Jacek.
P.S. What is a frequency range of CODE 25 speaker?
Hi I've just bought a CODE 25 and wondered what size USB cable I need? Doesn't seem to be your regular phone type cable.
I know I can override any CODE amp preset with CODE USB connections from the website or by changing on my phone while connected and saving either on the phone and/ or amp. But How do direct amp changes work with Gateway while disconnected and then synced later on?
In other words, if I save modifications on my amp to a particular preset and I am not connected to my gateway on my phone, when I do connect and sync later, which setting wins? Does the phone setting override the amp-stored setting (ie. back out the mods made on the amp / push the settings to the amp from the phone) or does the phone pick up the modified amp setting from the amp and store it in Gateway (ie, pull the settings from the amp and store in my phone)?
Also, I have the first 30 presets set up for ones I use to perform and are addressable using code programmable foot controller. If I want to archive/backup those presets someplace to guard against an unplanned need to do a factory reset, does it make sense to store them perhaps in the cooresponding setting in my Library ( the blue section of My Gateway ) That way i can bring them into the amps and store them one at a time from the library back into the presets on the amp, or is there a better way to backup/restore presets in the event of a factory reset?
1) Bought Code new, when released, USB port was loose and wont connect. Cant do Firmware or recording via USB. How to get service?
got at Guitar Center San Mateo Ca. When first released, hadn't ever really used USB, but realizzed it is messed up, like port is disconnected or broken. USB is wiggles and no connection.
2) Cant get Gateway to Recognize tye Amp while BT stream audio okay. tried all steps from this site cleared phone and cache, removed and reinstalled, no diifference. Multiple versions of Android. 5 to 8.
I have a CODE 50 amp...
1. Connected from PC using AUX cable so YouTube/Songsterr etc plays through amp.
2. USB connection to same PC for recording to Audacity.
When I play (headphones in) Audacity records the guitar perfectly but doesn't acknowledge the PC audio. I can hear both the PC audio & guitar track clearly in my headphones.
Is there any way to fix this?
My USB suddenly won't connect and after a number of failed attempts to reconnect with software solutions, I suspect the USB port on my CODE 100 Combo is to fault. Are there connection options available via the headphone jack? Are there fix or replace options for the USB port?
I am experiencing terrible interference when trying to use my Code 50 via Bluetooth / Gateway (Apple) App while recording on my Mac in Logic Pro X. I am using a microphone to record the Code 50 and using the Bluetooth Movies series world to change patches. The clicks/pops/noise/interference is loud enough to interfere with the recording process. Perhaps a DESKTOP (Apple) Gateway App via Code USB might be a solution for all users experiencing similar issues? I am running the most current Firmware. Any current solution to my noise issues?
bonjour je me présente christopher , je viens d'acheter un marshall code 50 et je voudrais savoir si quelqu'un peux m'aider car je veux enregistrer le son de mon ampli pour pouvoir mettre mes enregistrements sur une clé usb par la suite et écouter si quelqu'un peux m'aider ce serais cool merci(christopher)
If I want to plug my 100h into my PC via USB, does it still need a speaker load or can I use it without a cab connected?
Why in the world would Marshall advertise right on their site for the code amps that you can record the code amp into your DAW, but not provide an asio driver? This is false advertising. Yes there is asio4all, it is not for a Marshall per se, and it doesn't work real well, it only records at 48khz, most daws will go to 96k, if not all the way to 192K? What gives Marshall? Plase put out an Asio driver for this otherwise great product. please. It can't be that hard if you can write the"code" for this amp. You are relly missing the boat here guys
I purchased a Marshall CODE 100H + 212 Cab recently.
I downloaded the Marshall Gateway app and have created a My Marshall account.
The Amp came pre-loadedwith a 100 presets.
The Marshall Gateway app also came pre-loaded with 100 presets,
but the Gateway app presets are different from the ones in the amp.
I synced the 100 presets in the Gateway app to my "My Marshall" account Library.
I have edited and saved some of the Presets on my Amp.
I want to transfer the edited Presets on my Amp to my "My Marshall" account Library, and then put them in my Gateway app,
How do I Transfer a Preset FROM my CODE Amp to my "My Marshall" account Library?
I see the option to transfer a Preset from My Library to the Amp,
and I understand how to manage / organize the Gateway app presets from the Library,
but I don't see a way to put a Preset on the Amp in the Library.
Do I have to manually re-create it in the Library?
The My Gateway online interface is great for managing / organizing the Gateway app presets from the Library.
It would be useful if there was as similar interface for managing / organizing the presets on the Amp, when connected via USB.
I can’t get the Code connected via usb to work any news on this nothing happens at all plugging in the usb and nothing in my DAW
Hello, I have acquired the CODE 25, really an excellent amplifier, very versatile and very good presets. My problem and please I hope you help me to resorve it, is that even though I can connect via Bluetooth, I can listen to my tracks ....... the big problem is that when I want to use the FX or presets it appears that there is no amplifier connected ... (either from my android phone or my Ipad I ... I do not understand what the problem is.) Secondly, when I want to install the MARSHALL FIRMWARE UPDATE UTILITY, to enter presets or update the ampli, does not recognize the connection.I request guidance to be able to make full use of such a beautiful tool for my music.I use Widows 10 and G. Chrome.For your attention, thank you very much
I've got a (not very big) problem with recordnig music via USB. I use only clean sound, typical settings for my guitar equipped with 2x Wilkinson WVC humbuckers are:
preamp - DSL, gain - 2.0 (increasing gain over 2.5 makes sound NOT as clean, as I want it to be), volume - 10, B/M/T - 7/10/5, noise gate - 0.5
power amp - American, presence - 2, resonance - 6
I tried Audacity and Presonus Studio One, and in both cases recording level is about -20dB. Of course I can normalize volume in post processing to let's say -3dB and I still have quite satisfactory quality, but I loose this 17dB of signal/noise ratio.
Any suggestion how to increase USB output level?
Is it possible to control and make changes to the existing preloaded patches of the Code App via the USB port connected to a Windows 10 Laptop?
or the Marshall Gateway App works only with Android/iPhone via Bluetooth?
I connected my Code 50 to my laptop via bluetooth, but the my.marshall presets says "CODE not connected". I tried connecting via USB, but the amp has a goofy connector that standard USB cables do not connect to. Also - I can connect via the Gateway app on my phone, but the presets I add to My Library do not show up (even though it says that they have synced).
Hi, i have a Marshall Code 50. I tried to record with usb input but there is a lot of noise (interference) every 10-15-20 seconds (random).
I have high quality cable and a yamaha RGX A2. With the oldest firmware version it was noisier, now with the v1.41 is better but how can I fix?
Sorry for my english.
First of all I love the Code 100 amp, however, I purchased this to practice with but also to use in a duo for small pub and club gigs.
I have been using two amps for stereo mp3 backing tracks and 2 guitar amps plus a PA all DI'd into a small 8 track mixing desk using line out's from the amps.
The Code 100 unlike competitors amp modelling combo's doesn't have a line out, only headphones and USB (which also doesn't cater for ASIO as I use Cubase for our backing track recordings). Is this amp only a practice amp as the ads suggest it is powerfull enough to use in small gigs, but without a line out, the volume would have to be independantly changed manually rather than having everything in one place on the mixer as solo, duo and bands have done for many years.
Do you have a solution for this as do not want to have to send this back and go for an inferior competitors model as you feature tops in all the reviews. Seems like a big omission for giging musicians!!!
Or is there an upgrade planeed for those who need a line out for DI'ing to a desk to manage the total sound or for live recording, or is there something we could purchase that connects to the USB interface that could go to the mixing desk?