I need manual for code 100 combo

Hi, could someone give the que how to reset Marshall monitor II ANC headphones. The way that Marshall's manual suggests doesn't work.

Thanks in advance!

Hello,    New amp I procured and I am hoping to get some Q's answered regarding. 

It did not come with a footswitch and being new to all of this I do not know why I need one or which footswitch to get ????

Also, I was told by the original owner that it is quite than it used to be and may need a new tube.   Also do not know which way to go with this ...   

Last point is when switching over from clean to overdrive it is buzzing and I am not sure why...

After hours on youtube and reading the instruction manual I am even more confused. 

Thanks in advance for comments/advice. 

Wade

I got a CODE100H and the manual says that you never must run the amp without an cab connected. But there are so many videos and tutorials where the amp is plugged only via USB or headphones.  Does it make a difference if is there's a DAW, a cab or headphones connected?

And another problem is the delay while connected through USB. How can this be solved?

I noticed there is an emulated out on the back of the 20Watt Dsl head. From reading the .pdf manual, I understand that the head needs to stay connected to the speaker cabinet. So I know to never un-hook it, however - My questions being - 

Do I need to be in Stand-By mode to actually use the headphones? If not, will the sound still come from the speaker cab? 

Also, can I just plug my headphones directly into the Emulated Out? the .pdf manual says the Dsl20 Emulated Out supports Headphones. But I've seen people comment in other places that you need a headphone amp that increases volume or something. I haven't been able to test with headphones yet, and I kinda' wanna' get the right answer on this before I try. Thanks. 

Loving the Amp and Speaker cab though haha. Just came in yestreday. 

I have an issue with tap tempo on the Code 25 with 1.45 firmware and wondered if anyone else has the same issue.  The manual says you should "press MOD and DEL selection switches together". When I do that the amp does indeed go into tap tempo mode (tap the selector switch to set tempo), but regardless of how quick I press the buttons or if I hold down one and then hit the other it always switches on the MOD module too. The other double combination switches (tuner and bluetooth) dont do this and work as expected and only switch on those functions without switching on or off any other modules.

Hi,

How do you control system sound (power on & shut down) volume on Emberton?

The system sound is VERY loud, and aggressive sound. 

It's silly when you hear relaxing yoga music, and then you're forced to hear very loud guitar sound at the end of the meditation session.

Thanks.

I have 2 cabs,   2x12(16 Ohms 100w) and 4x12(8 Ohms 240w).

In Code 100h manual, says the speaker output is MINIMUM 8ohms load. I can use my 16 ohms cab without harm the amp head or the cab itself?

I'm getting trouble in the 4x12 transportation, the 2x12 is way lighter. Until now I'm only using the 8Ohms cab in the code 100h.

Need to figure out why channel 2, the instrument and mic channel is not working. Channel 1 and mic only channel are working fine. Opened it up and took out the chassis and there is nothing obvious. The basic schematic shows the Channel 1 and 2 share the instrument input on the ring cable input. Not much info out there which is good news considering this amp has been in production for a while so it doesn't seem there was on going  issues. Any ideas? Thanks 

1. Tilt knob - does it affect Treble (above  4khz frequencies) or Upper Mid (1khz - 3 khz) frequencies?

2. Does Master volume knob on this amp, if set to 10,  actually produce power amp (EL34s) distortion or is it just a control for the overall volume output (loudness) with no influence whatsoever on power amp distortion ???

Hello, 

I recently found a JCM900 4500 series hi-gain dual reverb in mint condition. The serial is Y38091---I know that it was made in 1990, I was just curious past the "Y" what the remaining five digits might pertain to? I was really just intrigued by reading the history of these and was wondering if mine is one of the first few produced and if it would be possible to find out what tubes and components were used on this one. Also, is it possible to get a copy of the original manual? 

Thanks for any and all help! I love my 900.

Well as per title, I do not own a smartphone capable of using that app. So how do I use the equalizer? I bought the marshall monitor 2 for the equalizer as well as the ability to play over blue tooth from my laptop.

Is there some trick I am missing, there seems to be no manual included or a disk for drivers I can install?

I bought a code 50 from a friend, but he didn't have the manual. I found the manual on this sight, downloaded it as a pdf, but can't get it to print.  Is it something I'm doing wrong, or is printing blocked by the web site?

Thanks

Hello,

I am having trouble confirming if a speaker must be connected in order to use the D.I out on my Marshall 2525h. The manual only contains one sentence of information which doesn't provide enough clarification considering this can destroy an amplifier if misunderstood.

Would I have to connect my 2525h  to a 1x12 cab (via 1x8 ohm connection) in order to use the D.I output? This signal from DI would be sent to a Two-notes C.A.B.M for Impulse response, before going straight into the audio interface?

How do I turn on the tuner on the 2020 MG100HFX head? The quick start manual says nothing about it.

Will a Marshall PEDL90008 4-way footswitch be suitable to use with my MG100HDFX head, the manual only mentions using a 2-way footswitch, but other sources say otherwise?

Having problems storing presets to foot switch- manual not helpful. Does anyone have step by step instructions? Many thanks

Does anyone have a manual for a Marshall Lead 15 G15MS If you do can you pdf me a copy, Thanks Mike

 Hello I want to exchange valves in my Origin 20h, ordered some aol login from Tube Amp Doctor. After I exchange them do I have to rebias it? Is there a manual for rebiasing? I wasn't able to find anything which would give me even slight bit of a hint about it .

thanks

Hello everymarshallers!

I'd like to know what actual pedals/stompboxes are modeled/emulated for ovedrive ("ODR") and distortion ("DIST") on the CODE series.

The User's Manual only says "Classic" to describe both, so they must be some well known for us all (however, the Marshall Guv'nor is especificated, so I guess it's because a conflict about copyrighted trademarks).

Is it possible the gentle Marshall Team can inform us about it here in the Forum?

Anyone have made comparations?

Any suggestion about any other gear modeled on CODEs?

Best greetings and music ;-)