Hi, Do someone know if the "custom voiced" speakers on a CODE 4x12 8ohm cabinet are the same as in the mg412a cabinet ? The mg cab is loaded with celestion g12-412mg 8ohm speakers that look like celestion rocket 50 but seem to be rated at 30 watts ... because the cab is rated 120w... some AVT cabs are loaded with celestion g12-412avt and some with celestion rocket 50 but AVT cabs are 16ohm (maybe the cause of suffixes change on the g12..) I've browsed  the celestion website to find some answer and the only one that had the same magnet is the rocket 50 and is rated to 50 watts... i would like to know what kind of speakers are on the CODE cab and if the mg412a cabinet sounds about the same as the CODE 412 cab with a CODE 100h head ...i don't like the format of the CODE cab...but want to keep all the tone modeling capabilities of the CODE 100w head

I recently hooke this head unit up to a 2 2x12 cabinet 8ohm and per instructions and at full cranked volume barely hear anything

Any suggestions or tips before persuing it being faulty? speaker cable hook up and checked with another cabinet and still same thing barely any volume . 

 I have just received my first ever Head Amp. So very excited about it. My question, is it totally unadvisable, to test out the headphone socket without connecting up a cabinet to the head amp? 

I was hoping to test before  obtaining a cabinet  (212 I had in mind).

However it does not advise using it without a cabinet connected. Is there a risk in blowing up the circuitry otherwise? 

Thanks for taking the time reading this. 

The has 2 8OHM  outputs. Do i plug both into both 8ohm inputs on cabinet and run in stereo?

Hallo,

cannot find any technical detail on this speaker. I would like to know the Sensitivity (is it 100db as the Vintage 30?) and the Frequency response diagram as well for the 16 Ohm type. I'm gonna to buy a 1936V 2x12 speaker cabinet and I would get these information, please.

thank you.

cheers

Manual says "Connect a single speaker cabinet here for the DSL1HR head". Is it means I can't use cabinet with two 8ohm speakers in series?

Hi folks!

My brand new DSL20HR has a great sound with my MX212AR cabinet, but when I want to plug it on my mixtable with the emulated output the sound is very bad.

I've tried it on the STB position with my speaker plugged. The sound is bad even with the headphone : a lot of hum and the volume should be at the max.

There was a lot of highlights on these feature :

"Marshall has teamed up with software mavens Softube to create exceptional tones "

I don't understand it can work so bad. I really can't use it and I many other users that seem to have the same problem.

Thanks for your help.

Best regards.

Pierre

Hi, can anyone explains to me WHY we can't use a CODE 100H without the cabinet? For VALVE amps there is a good reason for which you need the cabinet always connected but for solid state amps it seems very strange.

Is it maybe an error in the manual? Maybe it's a phrase that has been written for all the Marshall valve heads and it was mistakenly added to the CODE as well?

Please let me know, I have an application where I only need the 100H coming up soon.

Thanks!

I'm looking for a Marshall Cabinet Cover that will fit a MX412BR.  I perfer one that does not have the side cutouts. Looking for 100% covverage.  Thanks. 

I have a Line 6 Flextone II Head that will sit on top of a Marshall MX212..  Need size 13" x 30" x 30" coverage..  

Hello I'm considering to buy DSL1HR or CR for silent recording at home. But I would like to use fx loop SEND output to record raw valve soud to apply impulse response later.

Is it safe to unplug cabinet, and without connecting headphones use these amps in such manner? 

And if so, why? Usually valve amp needs speaker load

Thank you in advance for the answare!

Sergey

If I connect my DSL40CR to an external speaker cabinet should I disconnect the internal speaker ?

How are the four Celestion G12M-25 (25W, 16Ω) speakers wired ― series or parallel ― inside the 1960AX and 1960BX extension speaker cabinets?

How are the four custom speakers (8Ω, 50W) wired ― series or parallel ― inside the CODE™ CODE412 extension speaker cabinet?

How are the two custom speakers (4Ω, 50W) wired ― series or parallel ― inside the CODE™ CODE212 extension speaker cabinet?

Which speaker jack is for the 8 ohm,  the one in the very center or the one next to the 1x16 where the cabinet pluggs in? Their are 5 jacks, so counting from left to right which one is the 8 ohm jack ?  Thank you.

How do I register my new speaker cabinet in the United States?

The warranty card gives me a weblink of www.marshallusa.com/warranty, but when I go there, it says; "EPIC 404! AN EAR OCCURRED WHILE PROCESSING YOUR REQUEST." 

Hi,

I recently buy a Code 100 head and 4x12 cabinet and I loving it!

But I do have one concern the hum,there is a humming noise coming from the speakers when not played or not plugged in?

When I put the power one the humming is there and when played humming isn´t noticeable.

List of factory presets for CODE 100H head. From 2019, the presets are different than combo models. Rig info: the CODE 100H head and 4X12 cabinet.

Hi guys, im new to head and cabs as i have been a combo guy for years. I recently purchased a code 100 Head and i really do not want to use the code cabinet and want to get a better upgrade. I have a guy selling a 2004 1960A cab for $500 AUD OR I was thinking of getting either a 4x12 origin cab or a 4x12 SC cab. 

any ideas ? 

thanks :) 

My question is concerning the Code 100H. When using an external cabinet, is it better to use the preset power/cab selections or to turn them off. Does this apply to the Marshall code cabinet and any other cabinet, or just to a different cabinet ie: 2x12 Morgan ? Thanks.