Questions
Showing results 41 to 60 of 100
0

votes

1

answer

1.7k

views

Hello.  I have a Marshall Code 100 Head, 4 12 cabinet and the 2 12 combo amp.  Absulutely love these amps.  I also have the 3 way footswitch.  What I can't figure out, is how to be able to turn off and on the REVERB from the foot pedal.  Is there a way for this?  It defaults to allow you to access the Distortion, Modulation and Delay but what about the reverb?  Any ideas?

Thanks, Larry

asked 21 Jun 2019 at 05:33 PM

Larry Tucker
0

votes

0

answers

916

views

If I purcase the marshall code footswitch and plug it into the f/c input on my code 50 do I connect  the looper and the drum  machine into  plugged into the input on the left.  Would this stop the drums from getting the effects on the effects on the guitar

 

asked 07 May 2019 at 12:59 AM

Harris Gleen
0

votes

1

answer

904

views

I'm noticing a significant volume difference between the presets I have programmed on the footswitch in A2 & A3, is there a way to adjust this so the volume remains the same when switching between A2 & A3 ? 

asked 05 Apr 2019 at 04:52 PM

Ron DeMartino
0

votes

1

answer

2k

views

Hi please refer to this previous question to help explain the background to my question:  https://my.marshall.com/forum/question/1479/marshall-code-100---should-it-have-come-with-a-2-way-foot-switch?filterType=recent&myActivity=True

Basically I bought a Marshall code 100 (no it's not 100H or 100C just a plain 100). It was out of its box and on display but discounted by about $180 because it had a slight dent in the base. The store rep claimed it had not been used. I bought it due to the price but after a few months I realised it should have come with a 2 button footswitch. I then raised this fact with the store and they agreed to supply me with the one that should have come with it. It has been about 6 months since they promised me they would replace and every time I ring up they come up with some bullshit excuse like "oh our suppliers on the other side of the country claim it is not sold as a spare and they have to order it in and they are not receiving any new stock of this item until Feb". 

So Feb has come and gone so I am about to ring them and vent my frustrations on them. Then I thought maybe I could get the PEDL 91009 foot switch instead of the PEDL-91010, at a discounted price (perhaps to the value of the cheaper switch that should have come with it), as I am told it is much better.  As I have never had or even used a foot switch and am completely clueless on them I have a few questions:

Does the basic PEDL-91010 footswitch only allow you to switch to the next preset up or down on the preset list of 100 presets? Or can you jump from like preset number 4 to preset number 98? If it only allows you to switch to the next one up or down does the 91009 model allow you to switch between any two presets on my list? Does the 91009 model allow you to program more than 2 presets to switch between when playing a song? 

Finally, one responder to my other post mentioned that the Code 100 only comes with a basic 2 way footswitch and that the PEDL 91010 is an optional extra. But this contradicts what others were saying (eg that it is the PEDL 91010 footswitch that it comes with).

Anyway I am confused and need all this cleared up so I am fully armed when I next call the store.

asked 10 Mar 2019 at 02:04 PM

julien casella (1)
0

votes

1

answer

999

views

So about a year ago I got a footswitch for my Code 50, and when i first got it, it started banking backwards on it's own. I was able to stop it...until now. The worst part of it, is when i go to use the amp's tuner, it immediately exits because it thinks the button is being pressed. When it began a few days ago, I was able to press the bank button to increase the bank and counteract the issue, but now the bank button stopped working. Maybe I pressed it too hard or too much or something. I cant remember how I fixed it last time or whether or not the bank button worked, but all I know is this time it might be done for good. If anyone knows of this issue or has had it happen to themselves, please let me know how I can fix it. I dont remember all the presets that were saved to it, but I can remember a couple. Please help!!!

asked 08 Mar 2019 at 07:57 PM

Keenan Borgerson (3)
0

votes

1

answer

848

views

I use the programmable footswitch with my CODE 100H. Has anyone experimented with a second footswitch to add another 30 patches? Is it possible to use 2 foot switches with an a/b box, or manually switch controller cable outputs, in this manner? Can you hear me Mr. Marshall?

asked 12 Feb 2019 at 09:44 PM

Mark Solis (2)
0

votes

1

answer

1.2k

views

I own a code 100h with the footswitch and I love this rig. I play through a 4x12 Celestion cab with gold standard vintage g12-75’s. It took a little bit of time to really become comfortable with the app and head interface, but it’s like riding a bike now. Thank you for this technology, Marshall, please don’t stop supporting us Kvlt CODE players!

Can I make a suggestion that you could profit from and would add to our Marshall experience and branding? Why not create virtual pedals and accessories that can be purchased and downloaded onto our CODE rigs?  

For example why not be able to purchase  “extra slots” and effects so we can run a wah and distortion pedal or run 2 delay pedals at once? I’m sure there are other itches that players could scratch this way? Maybe even add outside name brand pedals? You know, like that fluorescent green scream thing?  

 

Like I said, I love this rig, and it’s portability. If could ditch the separate wah and boost pedal I carry as part of my signal, I’d happily give you my money!

asked 10 Feb 2019 at 04:28 PM

Mark Solis (2)
0

votes

2

answers

1k

views

Hello, I got a code head and also the programable foot controller that I havent connected yet. My question is about the 30 programable presets. does this mean I can have total 130 presets or 70 factory presets and 30 custom presets.

asked 06 Feb 2019 at 04:45 PM

Robin Morgan
0

votes

1

answer

779

views

i have a code 50 amp and i have a boss footcontroller Fc200. Is it possible to used this as the footcontroller instead of buying an new one? Already i have almost more pedals than there is room on the stage 😀

asked 02 Feb 2019 at 02:09 PM

Kees Leautaud
0

votes

2

answers

1.6k

views

Hi there.  I am not a native but I hope you'll be able to get me right.I have been using Dsl 15c for about 2 years and all of a sudden the amp stoped producing any sound. All controls freeze, footswitch is non responsive. Led’s and tubes are still lit. No pedals in line. I turn power switch off then on and hear sound like a relay click in the background and then sound immediately cuts out.  My tech told me the problem is 99% in the microcontroller AT2313 because inside all fuses are still intact.  He was able to read the code and fix errors that cut the sound out. However, it did not help because some of microcontroller ports were damaged(most likely it was a factory defect). Is it possible to re-record the code to new microcontroller or maybe there are some other options to consider?

Thanx.

asked 03 Jan 2019 at 03:29 PM

Alexandr Forrest
0

votes

2

answers

744

views

I bought the footswitch and the Marshall Code 50 a few months ago. Both working fine until doing a gig  last evening, I hooked up my footswitch to the code 50 with the lead that came with it. No lights showed up, but the amp working fine I tried changing with a different lead, and the footswitch still no lights. The footswitch won’t work. Anyone out there has a similar issue please. Any suggestion please? Thanks in advance

 

asked 10 Nov 2018 at 06:07 AM

Tom Tang
1

vote

4

answers

4k

views

Hey guys

I'm trying to figure out how to use tap tempo on the footswitch with my marshall CODE amp.

As I understand it, I should be able to "stomp" in the tempo of my delay via the footswitch.

I have no idea how to do this though.

Please help

Thanks

Gerbrand

asked 11 Oct 2018 at 02:57 AM

Gerbrand Nel (7)
0

votes

1

answer

756

views

Does the programmable footswitch have tap delay capabilities? If not, how can I achieve that?

asked 24 Sep 2018 at 02:11 AM

Jamie Carter (16)
0

votes

3

answers

1.8k

views

I have a Code 100 and want to be able to add auto wah on top of a preset with another (Overdrive) pre-fx set and use the (4 way) footswitch to switch it in and out - can this be done ?

 

edited 03 Sep 2018 at 01:00 PM

Mike Palmer

asked 03 Sep 2018 at 12:58 PM

Mike Palmer
0

votes

2

answers

852

views

When I hold down footswitch 1 to access the turning on/off of my compressor it doesn`t work anymore. It does this in all banks and patches yet worked perfectly previously. I`ve only had it a week so is it faulty or can I resolve this please?

asked 18 Aug 2018 at 09:58 AM

Mike Burrage
0

votes

0

answers

889

views

Hi guys i have a Code 50 Amp and footswitch. i have recently started to having a problem. when i am on a patch and hold in the Selector on the Switch for instance if i am in Bank B3 and hold down the B3 switch, you enter a mode which you switch off FX, Delay and reverb. i have notiched that when i go into any bank like that and want to go back out to choose another patch my amp buttons and knobs & footswitch is non responsive and i have to switch the amp on and off for it to respond again, this is very anyoing. any feedback on what the problem might be

asked 30 Jul 2018 at 01:18 PM

Dominique van der Westhuizen (1)
0

votes

1

answer

1k

views

I was dicking about with tones, as you do, and when I meant to save my custom tone to my footswitch, and accidentally saved DSL Clean Chorus to #11 on the amp, Some Dely For You Too. This preset just happened to be one of my favorites. Is there anything I can do about it?

edited 28 Jul 2018 at 08:56 PM

Riley Helton

asked 28 Jul 2018 at 08:55 PM

Riley Helton
0

votes

1

answer

1.2k

views

I was dicking about with tones, as you do, and when I meant to save my custom tone to my footswitch, and accidentally saved DSL Clean Chorus to #11 on the amp, Some Dely For You Too. This preset just happened to be one of my favorites. Is there anything I can do about it?

asked 28 Jul 2018 at 08:55 PM

Riley Helton
0

votes

1

answer

1.2k

views

Hi,

can my Code 100h works with a standard midi footswitch? The Code 100h has a midi-usb but my Digitech Footstwitch has a standard-midi inteface: can i use an adaptor midistandard-midiusb?

thanks,

paolo

asked 18 Jun 2018 at 08:55 AM

Paolo Goi (1)
0

votes

2

answers

1.5k

views

I recently purchased a new code 100 which was a display model. They didn't have the box for it or the owner's manual. I subsequently downloaded the manual off the internet. On one of the pages concerning the front panel functions it talks about the F/C jack socket and mentions "connect the supplied 2-way footswitch" but I never got one with  it. Has anyone recently purchased this model and did it come with a 2 way footswitch  for scrolling through presets? If so I will try and get one off the shop for free. If they argue their way out of it are they expensive to buy separately? **Update to this is that the manual I have downloaded has code 100 and code 100h on the cover so maybe the footswitch comes only with the 100h?

 

edited 17 Jun 2018 at 01:25 PM

julien casella (1)

asked 17 Jun 2018 at 12:26 PM

julien casella (1)
Showing results 41 to 60 of 100
Loading - please wait...