Hello!

!!! Ok, my bad. Figured it out. Had to put the amp in pairing more (Rev & Power) - then all is well. Sorry. !!!

(Feel dumb, bt I'll leave this in case someone else has similar issue.)

I had the amp successfully paird with a prior phone (Moto Droid as well - 2 yrs old?) Got a new phone - described above - Android v7. Not able to pair. Have uninstalled the Gateway app, (that got in the way last time, until the phone & amp were paired, then an install / connect went fine). This time... I get a cryptic, possibly IP6 number that looks like a device address. No code to enter, or anything to do. Phone says "Pairing..." waits maybe 10 seconds, then returns with "Pairing..." gone - no message, no nothing. Tried many many times. Cannot "forget the device" - phone doesn't offer a lot of choices: pair or disable Bluetooth is all...

Will the Code work with this phone? IS there a trick I hope I don't know? I sort of like the app - although I often use the knobs - it's just easier... So... I'm not going to hate you forever, but have to join the folks that are dissappointed with this. Amps are marvelous, but this software isn't measuring up I'm afraid.

Anyway, any help much appreciated!

Thanks

Steve

Hello !

Like many of lucky owners of Marshall Code 50, I also have problem to pair Gateway app with Code. My phone (Ulefone Power with Android Mashmallow 6) recognize amp thru bluetooth and even play MP3 music, but can't work with Gateway. I wonder why ? I tried to rebooth code and phone several times, also install and uninstall app few times, but nothing helps. I upgraded firmware on my Code 50, still nothing. Can i expect fixed new version of gateway soon, and will it be tested on more smartphone brands ? 

greetings from Zagreb/Croatia

Tvrtko Grgic

tgrgic@hotmail.com

Hi there Marshall team,

I was wondering if you could help me with a problem that I am having between my Code 25 amplifier and the Gateway app. I am able to pair my android device and the amp via Bluetooth just fine but once I am in the Gateway app it doesn't detect my amp at all, even when I press "scan for amp" it just says no amp detected. 

I think I should add that I have been able to connect it to my apple device without any problem at all.

It would be highly appreciated if you got back to me.

Thank you.

Hi,
I have a problem when saving Presets from my Marshall Code 25 amp to my phone (Android).
The saved Preset repeats/copies itself about 20 times. Therefore, the app Presets are unusable because I have to scroll down or up 20 duplicates before I reach the next Preset.
There is no way to delete those Presets, and when tapping on one the app freezes.

I already posted this same question in an existing thread in which other people were notifying this same issue, but that post was deleted...
In that post you said you where working in a solution to this, but its have been 5 months since the first report of this problem, so
I'd be grateful if you could fix this as soon as possible and kindly ask you when do you plan to release the Gateway app fixed?

Thanks!

Problems with the Marshall Code Gateway app music playback feature noticed on a Samsung A3 (2016) smartphone running Android 5.1.1.

1) The currently loaded tune name is usually not updated on the display when switching to a new tune. I say usually, because I've seen it change on a couple of occasions. The album graphics however appear to change as expected, regardless of the tune name displayed.
2) The volume control slider on the display defaults to about 1/5, however the output seems to default to full volume. Moving the slider upwards immediately drops the volume significantly, and it does not even seem to reach back to the intial volume level with the slider in the rightmost position.
3) At least on one occasion there was some skipping in the playback of the tune and noticeable tempo changes while adjusting the output volume using the app slider. Might also have been caused by moving around in the room with the smartphone in hand.

My Samsung tablet pairs with my CODE 50 but Gateway app will not change the amp settings. It works properly with my Motorola smartphone. Both are Android.

When i try to play a track to my Code 25 using gatway on my motorola droid turbo 2 running android 6.0 the search window opens but remains blank other then the ok and cancel buttons at the bottom. Please help. thanks!