Re you going to release a cover for the cdoe 2100 combo? I cana see on the Marshall site that you do a cover for the 25 and 50, but why not the 100?
http://shop.marshall.com/k/search?q=codee+100+cover
Bought a CODE 50 two weeks ago and LOVE the tones - great reproductions! But I have the hissing problem as well. Quite noticeable as a chord or note decays. At first, thought it was normal 60-cycle single coil pickup hum, but it is not.
Read similar Posts on the Forum, so tried the firmware update and it did not help. Noise gate not really an effective alternative, either.
Team Marshall, any other solutions in the work Again, otherwise I love the amp and want to keep it.
Thanks.
Hello guys, i own a marshall code 25 since last summer and about one week now as i play the sound dies sudenly. The amp seems to work all the knobs,the footswitch but no sound at all. The sound comes back when i restart it but after 5-10 minutes of playing same thing happens. I have installed the latest firmware. Does anyone else has the same problem? Any advices would be pretty much apriciated. I bought the amp from andertons, i sent them an email like 3 days ago but no answer yet. Is there any warranty?
My gear:
Fender Standard telecaster
Marshall CODE 25
Hello,
Yesterday I received my Code 50 amp. I played some hours with it and there is 1 thing that i noticed. I play most of the time at home through a headphone because neighbours, and the presets aswell as some own created sets sound really muffed if I add any Cab. I tried diffent Cabs but for me it sounds way clearer without a cab model. I was wondering how this is possible? Did i miss something? When I remove the cab from a preset add lower the presence by 2 it sounds so much better
And when playing through the speaker while gigging with friends, will this difference still be there or is a cab model "necessary" when playing through the speaker?
Greetings, Tom
Hi all
Requesting any help for amp settings, I want to break free - Brian May Guitar Solo. I know the Solo was played on a Synthesizer but Brian also plays that solo on his guitar. Does anyone have CODE 50 settings that comes close to this Solo sound?
Regards
The American amp model on the CODE is quieter in volume compared to the Marshall models...(the OD models to be precise, not sure about the clean ones)
Any reasons why?
I want to buy a Marshall AS100D acoustic amp from an authorized dealer. I can not find anyone that has one in stock other than Amazon. Its listed for $724 an odd price and different than any other price I find, which is usually $699. My concern is Amazons listing states: "Ships from and sold by Amazon.com". If I buy this amp from Amazon and in the warranty peroid need to have it repaired will the warranty be honored by Marshall and Marshall Service Centers in USA?
Thanks,
Ricky H.
I was very disappointed by the lack of the ability to disable direct monitoring of the CODE signal by VST ... I'm not satisfied with the sound quality of the CAB-sim, but I really like the sound of the AMP and I wanted to use CODE through VST with IRs - but in parallel with the VST there is always direct monitoring from the Code and does my work in vain...((
USB
Line IN
the chorus on my Code 50 is not working. I’ve had the amp about half a year, but not really used the chorus until recently.
If I turn the chorus on, the sound changes a little bit, but it’s not a chorus sound – although the speed option has an effect.
If I switch between CLS and VIB a few times, sometimes the chorus will suddenly kick in, and sound good, but if I turn it off or change presets, the chorus reverts back to its barely-there sound.
Has as anyone else suffered from this? Any tips? Thanks.
Hi, I have successfully been able to pair my Iphone 5s to the Code 25 2 times now, and when I try to connect my gateway app to the amp, it never finds it. I've tried till I'm blue in the face, and they just will not connect to each other......frustrated! TY
Does anyone else have a problem with the Code Editor software not fully displaying on the screen? Only the left half of the screen shows.
Does anyone have any tips for using the headphone jack on a Code 50 as a line-out to a mixer that goes into a PA system? I tried it over the weekendand it sounded terrible.
Hello all,
I have had my Marshall CODE 50 since last summer with no issues whatsoever...until now. Today when I decided to turn on my amp it was going NUTS. Whenever I turned up the Master dial my presets kept changing rapidly on their own and the amp would not output sound whatsoever. I tried updating the system's firmware and even performed a factory reset but nothing helped. Has anyone experienced a similar problem? Any advice or help in the right direction would be greatly appreciated.
hey Team Marshall,
I have the foot controller and a Code 50. Dig them both, GREAT AMP!! How do I over write a stored preset on the controller. Ex: on A1 I have DSL CLEAN I want to assign the TUNER to A1 then on A2 assign DSL CLEAN.
I just recieved my Code 50, and am still trying to learn how to use it. The main thing I'm interested in doing and learning is using an expression pedal to go between sets but am not sure how to go about it. I was told I may need to get the additional Code footswitch to make that possible. Help please!
I have a CODE 25 that I’m gonna be using to record. The pitch shifter sounds artificial set to an octave down to simulate a bass. I also have a Digitech GNX4. Can a bass be run through the CODE25, or should I use the GNX4’s Whammy effect to do bass?
I have purchased new Code 100 (a demo from Sweetwater) I am not able to connect the amp to my personal device. When I press the Rev and Power buttons to connect, the blue lights flash, the device number shows up on the amp but either of my devices (an I Pad and an I Phone) will not recognize the Code amp. The Code Amp does not show up in the "My Devices" so it never has the opportunity to pair or show up as connected . My phone and Iphone recognizes other bluetooth items, ie, head phones, speakers etc. I have tried the FAQ suggestions and have tried the recommended fixes and I am still not able to connect.
I have not done a firmware update on the Code 100.
Any assistance would be greatly appreciated.
Thank you,
Steve H.
Hello,
How can I program my code 50 so I can switch up/down through all my 100 presets?
I am using a 2 button footswich. Connected to a code 100H it worked fine.
After installing and running the windows firmware app in my windows 10 system I'm still unable to update to the 1.41 version for my code amp. The app response
states my code version is up to date. Please advise