Hello!
I just bought a Code 100 head and a cabinet. I want to use the head in a smaller room to learn more about it, using headphones or a MG15CFR,. Can I plug in the head to the input? As the cabinet is rather heavy its really hard to move it to another place than my "studio".
After the sparking and smoke, it fried some wire's inside and fried a circuit board!!! Should I just start over with the new Code!!! I love my old head, but cost is a consideration! Thanks for your outlook !!!
Hello, there. First of all sorry for my bad english.
I got two CODE 25, and it cannot be automatically paired with my phone again if it was rebooted.
When it is turned on, the blue light does just keep off and never get reconnection process.
Both of these got this issue after firmware update, and factory reset and troble shooting guide does not help anything.
I tried every ways so many times but it was useless.
There are many users suffering from this issue just like me... it is really annoying even this amp is really good.
Please leave an advice. thank you.
I picked up a Code 50 last week so far I love it and the possibilities it offers. Only issue I have had is when the Bluetooth is connected to my phone (Samsung Galaxy S7 Edge) if I get the phone too close to the amp I get a weird digital rattling sound coming from the amp. I have not tried to see if same issue happens with my Android tablet though. Has anyone one else had this problem or know the cause?
Hi,
When I connect Phone via bluetooth, I can not see a presets, only "tab to sync" when I tab it is shows this one and one or two more, but the rest is still tab to sync. Next connecting and all presets list is tab to sync again. Code do not want to synchronized with gateway. Do you have any idea how to change that?
I have a Code 100 and my instructor has Code 25 amps. I neeed a consise explaination of how to copy a preset from a Code 25 to my Code 100. So far, the tutorials and FAQs have been more confusing than helpful. I have the Marshall Android app and can connect to the Codes but have not method of copying setup from one to another.
Can anyone steer me in the right direction?
Thanks!
The problem is that when I put the distortion pre fx my amplifier does not give the sound even with any preset, the other effects work correctly only the distortion does not, however when I connect my headphones I get the distortion sound but without the headphones it sounds
Hi I just bought a code 50 and when i try to plug USB cable with my computer (mac pro), evrytime i saw that so it is impossibe to change preset.
I have a Marshall Code 100C and I want to connect a Boss RC3 looper and DR-880 drum machine to it and my Strat. Can anyone please tell me how I would do this? I am a new musician and desperately need an expert to help me with this one. THANKS!
I've been playing with my CODE 100 2x12" for about two months now and I've noticed no matter what I do to my amp settings(lower the treble, lower the presence/resonance, lower the tone setting of various fx, etc.) I still hear this metallic high end that can really be shrill at times. Is this an issue across all of the CODE amps or is there something I'm missing here with my settings and the combinations? My firmware is up to date as well.
EDIT: I have now sat down and experimented with the amp again. I cannot get a tone without any super high treble. It's now bugging me to the point of wanting my money back. I have tried every possible combination of pre amp/power amp/cab, I have turned off each individually and still had the issue. I turned the treble all of the way down and turned the presence all of the way down and the tone is still shrill. I either have a faulty amp or this amp, in general, sounds like garbage. It sounded great at first but I didn't realize how bad it was because the noise only happens when you get about 8 feet away which is annoying because my audience hears all of this high end and no articulation. Please, if anyone has any information on this, let me know. My guitar has an extremely balanced tone(it plays fine through my two practice amps), the cables are all new, the firmware for the amp is up to date, and there is no electrical interference. Any idea as to what I should do, Marshall? I've been using your products for years and I love them but this has been disappointing .
Will my kindle fire tablet work with my code 50?
I have the code 100 digital combo amp. Can someone try to match michale Angelo batio’s tone? Preferably the hands without shawdow tone album. Not the classic mab sound from speed kills. Thank you
Hi , would anyone know a sound close to the boss hm-2 pedal sound please?
I have no trouble recording directly from Amp into GarageBand, but when I open Logic Pro X, even though Code is selected as input and output, when I go to record it tells me that there is nothing connected. I don't what settings I could change for this and it works perfectly in GarageBand. Thoughts?
Got my amp, Code 100 combo and loving it, lucky to have a present of the new PEDL CODE Footswitch.
Being a bit of a noob to this new amp technology, I have managed to save a preset to the pedal, but no thanks to the instructional video mind you, which misses out the essential part that you are meant to press store on the amp and press the location on the pedal at the same time. There I was pressing the footswitch like it says in the video then trying to store. Very ambiguous instructions there, not clear at all.
However, one question is, once I turn off my amp, are the settings on the footswitch wiped out or are they stored until I want to delete them?
Also, it appears that I can only store to the pedal from the amp. So what if I'm using the amp in 'blue' mode from a hand held device?
That doesn't seem to work for me (using my preset from my handheld device and storing to the pedal that is) as it keep defaulting to an Amercian preset.
I may be doing something wrong, therefore I thought I'd ask the question, rather than just pull what little hair I have left out in frustration.
What are the limitations on the Code pedal? The documentation is woefully inadequote IMHO. The suppport video being just as poor.
I know the issue, it's software designed by software developers, with no end user experience being considered as opposed to using a UX team during development.
We either need more indepth clear and concise instructions, or a new video showing a detailed example how to save a preset (not just a voice over while looking at flashing LED's) and whether we can save, not only from the amp, but save a preset from the handheld device and store them for later use.
Sorry if the above is a bit of a moan, but if nobody moaned nothing would be done.
If you could answer my points above, that would be helpful.
Thanks
C.
I received my Code 25 just a couple of days ago, but still after updating firmware to latest 1.4, the amp continues to go silent after some minutes of playing. I have searched your Forums, and see that the issue were discussed already in Autumn 2016, but the firmware update came one year later; in October 2017. And still this issue has not been solved! What is this? Just give me One reason why I should not return this amp!
Best regards
Bjørn Engdal
Hi everyone!
Recently I bought Marshall CODE 25 and it's a great amp but I have one little problem with it.
There is a problem with MASTER potentiometer. I noticed that when I set it between 0-0.99 it is very very quiet but when I set it about 1.0 it becomes very loud. And in the effect it is very hard to play at "bedroom" volume levels. I must say that I'm disappointed - I had Yamaha THR 10 previously and it could play very well at every volume and it could play very quiet.
So to sum it up, is this some general issue with all CODE amps or something is broken in mine? Maybe master potentiometer needs repair?
i bought marshall code 50 stompware pedal 3 weeks ago from guitar center charlotte nc,the pedal was ordered and still have not received.I understand from talking with others that this is not uncommon as it has taken upwards to 2 months or more to receive these pedals.Question is why?Is there production problems,supply/demand,software issues or logistics.There isn't even a tracking number to track shipment.
Hello,
Recently I bougth a code 50.
When I want to stream music with bluetooth to the code, you can hear all kind of interruptions. The further the distance, the worse. But even with the laptop at a distance of 1 meter, you can haven interuptions.
I tried to solve the problem by upgrading to the latest firmware, but this has no effect.
When I am treaming to an other bluetooth device with the same laptop, I don't have any problems even at a distance of 8 meter. So the problem must be in the code.
Does anyone has the same problem?
What to do, or is this a defect?
Thx.
Just bought the 50. I have done the hold the 3 buttons down while turning it on to see the current version. I then connect the USB and it says USB connected Ready to update. But when I try to update from both the browser and the utility, it says "please connect your code". I have made the config changes on the troubleshooting site, and used 2 different laptops and 3 different cables but none of them will push the updates. It won't show the Code as being connected for some reason.
Anyone have an idea of where I am going wrong? I don't have any Chrome updates to do, and I am stumped. I don't want to have to return this if there is an easy fix.
Thanks in advance!