Questions
Showing results 141 to 160 of 3523
1

vote

0

answers

202

views

Omg my code 50 as just completely lost any sound no Bluetooth, no headphones, no amp what the flip is going on I've updated firmware hundred times reset amp hundred times and nothing dead as a door nail all lights and functions on amp work OK just no sound please please please help.

asked 13 Aug 2022 at 04:00 PM

paul Henson (1)
1

vote

2

answers

278

views

So I have had a new CODE25 for about four months, and two weeks ago it suddently started to go silent after playing a few minutes. No sound at all, very suddenly. Lights all still on, screen on (though maybe dimmed), and it won't recover until I power it down and restart--and then it may or may not play for a few minutes more after that. Didn't seem like an overheating issue (I rarely play that loud, and at the time I was using a sweet clean preset).

I've updated the firmware and still have the problem. I'm in Hawaii, and I'm not sure there's a Marshall warranty place here to do any work on it. Am I stuck returning it? Is this a common problem?

I absolutely love this thing, I'd hate to have to abandon it for poor dependability reasons.

Sean

asked 14 Jun 2022 at 06:23 AM

SEAN OMALLEY (1)
1

vote

1

answer

295

views

Bought a new DSL40CR in December of 2020 and last month it blew the 630 MA fuse on the PCB. Replaced fuse and swapped out all tubes. Now amp only works on 40 watt but has a lot less volume and does not sound like it did. The PCB has spots around CAPS that look burnt. Any suggestions? Can you purchase the PCB?

Dealer where I purchased not very helpful when I went to them to question about warranty, they kept trying to sell me a  new amp, not Marshall and said I would have to pay any and all costs if it was repairable. 

Really liked the amp when working correctly but am concerned that this would happen again if I purchase another one. 1 year and 3 months and total failure????

Marshall has restored my confidence in their product. They contacted me same day and gave me a list of where to take my amp for warranty repairs. The amp has 3 year parts/5 year labor warranty. Will update again when repairs are complete.

 

6/2/2022

I purchased a second DSL40cr amp and got my originalback from the shop. Took my repaired amp home before Memorial Day Holiday and so far it is doing great.

Again want to thank the people at Marshall for making this happen once I explained the problem.

edited 02 Jun 2022 at 03:26 PM

Roger Wallace (1)

asked 11 May 2022 at 11:13 AM

Roger Wallace (1)
1

vote

1

answer

336

views

I have several custom presets in my Gateway (via my PC at my.marshall.com). I synchronized my PC with the Gateway App on my Android phone and all the new presets show up (so far, so good). The problem is that when I turn on the Code 100 amp, all of my presets (in the Gateway Library on my phone) get reset to the default presets.

If I turn off the amp and re-sync, all of my custom presets show up again. When I turn on the amp, they all get reset to default values.

I updated the firmware on my CODE 100 and tried several different startup configurations, but nothing works.

Why is the amp overwriting the presets on my Gateway App?

asked 20 Apr 2022 at 04:22 PM

Reid Beck (2)
1

vote

4

answers

340

views

This issue is driving me crazy. My Code 50 used to work with my iphone and ipad, now it refuses to connect and I always get the above message.

I have performed the following:

1. Forgot bluetooth connection on both devices

2. Deleted iphone app and re-installed.

3. Re-paired and tried to connect with same issues,

4. Formed factor preset of amp with no luck.

I know the blueotth connects as I can play music through my amp from phone, I just cannot connect to update any presets.

Any solutions would be greatfully received, am getting so frustrated with this product.

asked 27 Mar 2022 at 11:37 AM

Geoff Ward (1)
1

vote

3

answers

474

views

Is it possible to put castors on code 100 combo? If so what type?

asked 22 Feb 2022 at 01:35 AM

Craig Romero (1)
1

vote

1

answer

674

views

Hello all. I am sorry for what is about to be a redudant and maybe to some, stupid question. I just got my dream amp, the JVM 410h. This is also my first tube amp and I want to care for it for long term use. For silent recording, I am running the line out with an xlr cable from my JVM head to my Scarlett interface, which I connect to my DAW and use cab modelling their for recroding. Do I lieave my standby switch on or off? The STANDBY/ silent recording notation is a little confusing to me. So should switch be pushed up or down? Also, should master volume be set to 0? Thanks in advance

asked 21 Feb 2022 at 09:23 PM

Nick L (1)
1

vote

2

answers

502

views

Hi Marshall Support, 

After buying Marshall Code 25 yesterday, I feel something is wrong with it. My Marshall Code 25 suddenly muted  randomly, even sometime in the beginning I try to power on.  I already updated the latest firmware, but it still happen. 

What can I do with this situation? 

 

asked 20 Feb 2022 at 09:43 AM

Achmad Bahtiarsyah (1)
1

vote

0

answers

413

views

Que tal' soy nuevo en el uso del ampli y según veo tiene detalles interesantes como el almacenamiento de presets en el movil, pero aún tengo unas dudas.

asked 01 Feb 2022 at 08:39 AM

Carlos Marquez (1)
1

vote

1

answer

484

views

Hello -  After really enjoying the Kilburn II speaker, I bought two Acton II speakers to couple them for ambiant sound when not using traditional speakers since you can't couple Marshall's wireless speakers. The Acton II is fantastic for sound and range individually *before* my attempt to couple them. I've had many complex compatibility issues with products over the years, but in this case, it's most puzzling why two same-model "coupled" speakers can be controlled via the iPhone/iPad I paired with them, as well as with the Marshall app (volume/sound settings) but cannot in any shape or form maintain simultaneous outputs even when they're placed right next to each other (well within the 10-meter Marshall spec). So before returning them back to store, I wanted to check with other customers if they've ever truly achieved the goal of coupling two Acton II's with both of them continuously and consistently playing in tandem without streaming drops. Thank you for letting me know,

What I've tried to so far:

- Followed Marshall's pairing/coupling intructions word-by-word. Though their instructions are incomplete and way below their reputation. 

What's more disappointing is the prompt you get in the app to "stay connected to Acton II but disconnected from Acton II in Bluetooth settings." Anyone know what that means? 

- Tried two iPhones and an iPad (all latest iOS).

- Deleted, rebooted, and re-installed the Marshall Bluetooth app (v1.3.1) for iOS.

- Moved the speakers next to each other to eliminate distance argument.

- Tested each speaker with direct Bluetooth to iPhone/iPad source without any issues. In fact, range is so much more when not using the Marshall app to stream to the speaker.

- Factory-reset the speakers.

- End result: The only way I was able to have them coupled was ignore their instructions, couple the speakers and then completlely shut down their app. after they show as coupled . However, there's no way for them to continuously and play in tandem (even sitting right next to each other with source iPhone/iPad next to them). They continue to switch between each other. 

- Also, Marshall needs to be clear that a "couple" can only function with one lifetime source. As soon as you try to use the speaker "couple" on another source device, you lose everything on the previous device and need to de-couple, forget speakers, re-add speakers to your device's Bluetooth, and then pray that the Marshall app will allow you to couple them again. Most of the 18-20 times I tried the whole process, I needed to uninstall their app, reboot device, and re-install their app. :(

Any help deeply appreciated before I return these speakers.

 

edited 29 Jan 2022 at 07:18 AM

Farzam T (1)

asked 22 Jan 2022 at 05:30 AM

Farzam T (1)
1

vote

1

answer

367

views

Hello all, I have an older amp MG15CDR. Bit of a problem with it. Crackles when you turn the gain pot or the tone pot. Seems to be worse when just turned on.  Maybe it's the potentiometers need replacing? Anyone else had this problem?  I can't see that Marshall will supply just these parts.

I would like to repair it, as it is a great little amp, suits my needs well.

asked 06 Jan 2022 at 02:49 PM

Peter Jolley (1)
1

vote

0

answers

396

views

Hi

I’m trying to decide which amp to get. My ultimate goal is to get out there and start gigging. I love big, dumb rock songs and have more or less narrowed down my search to a JCM 800. Here’s where my dilemma comes in.

For the same price, I can get either 1990 JCM 800 (50 watt) and a 1960A cab of indeterminate year or the little SC20 amp and cabinet.

Since I want to start gigging out, I am leaning toward the full-sized amp, with worries that it might be too loud even. However, since most of my playing is at home, I like the idea of the lower powered SC20. The one I played sounded super good at around-the-house levels. I am worried it won’t suffice if I try to gig with it. I have never played through an 800. (Or any half stack, for that matter. Right now my main amp is a Deluxe Reverb.)

So I guess what I want to know is which one is the better option for me? Do I prioritize stage volume or home volume? Does anyone even need a big, loud amp nowadays, or is a smaller, miked-up amp better in the long run?

asked 20 Dec 2021 at 03:53 AM

Natxlie Wood (1)
1

vote

3

answers

438

views

When I select the tuner the display only shows.  C : > | . I think the firmware is M1.1.

Any ideas? Thanks

 

asked 11 Nov 2021 at 09:24 AM

Bill Jones (1)
1

vote

1

answer

685

views

Looking at online forums, a lot of people appear to have a hard time getting a decent sound. Here's some tips that work for me, using a strat

1. Treble on 4, for everything. Presence on 1 for clean, 0.5 for dirty. Resolution on 5

2. Bass on 4 for american clean preamp, 6-8 for all others

3. Middle on 2 for clean, 5 for dirty

4. When using the onboard distortion pedal for blues keep the drive low = 1-2. Set amp gain at about 3 or 4

Hope this helps

 

 

 

asked 08 Nov 2021 at 06:25 AM

fred cav (1)
1

vote

0

answers

325

views

I have the original Marshall Stanmore. It's wired direcly to both a turn table and a CD Player. The sound recently began cutting out intermittenly. I hear a bit of static, the audio cuts out, and then a few seconds later, the sound comes back. I've been using the same setup for about a year with no issues. 

Any ideas?

asked 26 Oct 2021 at 11:45 AM

Fred Quattrone (1)
1

vote

0

answers

409

views

Is there any place to request presets?

asked 27 Sep 2021 at 06:34 PM

John Miller (1)
1

vote

2

answers

1.4k

views

I have a Woburn II speaker and I've paired it to my HP Envy Laptop but I keep seeing a LOW BATTERY message. I see that the device is paired but cannot play via bluetooth because of LOW BATTERY. The speaker doesn't have a battery.

asked 12 Aug 2021 at 06:58 PM

Nalani Nieto-Johnson (1)
1

vote

1

answer

326

views

Hello and greetings Marshall.

I have a Code 100 Combo. For this price is a great Marshall sounding amp.

But!!

Is harsh, but i use an external 7 WAY EQ pedal in loop and the sound with it , will be realy useful.

I have a Boss Katana too and has in built EQ effect. This Marshall Code series is very close to real Marhsall amps, form my opinion i think it's closer that Katana.

Why not is in Marshall CODE an EQ pedal effect, or an switchable 7 or 10 way EQ option  ??

I think what is most missing from the Code series is a usable 7-10 way eq pedal. Would it solve the harshness, the fizzyness.

I think it could be a great practice combo. with a more original Marshall sound than any Katana.

Please Marshall, include an EQ pedal or a switchable 7- or 10 way EQ option in an update as soon as possible.

Please :) !

let this product be worthy of the Marshall brand, or products.

Thanks.( Sorry for my English:)). 

Best Regards, Rob.

 

asked 09 Aug 2021 at 05:15 PM

Kovács Róbert (1)
1

vote

1

answer

474

views

Hi all:

Love the code.  BUT had a couple of basic questions( I think).  THANKS for any answers the community may provide!  

1)  Does creating my own preset overwrite the one I've selected?

- Is there a means to KEEP all 100 and simply add my own library or presets?  

2) Is there a base preset that is the AMP in its essential or basic state from which I can build new presets?  

I've come from a long line of Marshalls,  Most of which are the kind that you just turn knobs and make sounds!  

asked 08 Aug 2021 at 09:28 PM

Matthew Kernodle (1)
1

vote

2

answers

1.1k

views

While using the Marshall Gateway App on my iPhone 7 or SE (I'm assuming this happens on other iPhone models as well),  the "Playback" page automatically defaults to "Apple Music" when I want to add tracks to jam to with my Code 50 amplifier. 

My question for Marshall Support is: Can you make the iPhone Gateway App allow selections of tracks from locations other than "Apple Music" on the "Playback" page?

It would be great to be able to select tracks from my other files like "One Drive" or "Files".  Your competitors like the Boss GT-1 and the Spark 40 allow tracks to be added from ANY location when using their jam-along features. Limiting your choice to "Apple Music" really limits the jam-along experience on your app.

Thank you for considering making this useful update to your iPhone app.

asked 20 Jul 2021 at 12:07 AM

Kevin Towns (33)
Showing results 141 to 160 of 3523
Loading - please wait...