hi , can I swap out the ecc83 preamp tube in V1 for a ecc81 in a SC20H? I’m just trying to lower gain to a much cleaner sound - preferably to the origin clean .
Any suggestions - outside of “ buy an Origin “ ;)
p.s REISSUE THE JMD:1 heads !
Hi. I'm having a problem with my DSL5CR. When plugged direct into the amp and switched to the Classic gain channel it works perfectly. However, when switched to the Ultra gain channel, the guitar is very faint and what can be heard is a weak-fuzzy sound. When I first noticed the problem, I thought it was a case of the tubes needing to warm up, as after 30 seconds the level would gradually increase, unfortunately the problem has got worse. Could it be the pre-amp tubes at fault?
It's been ovem a year and a half since there's been a firmware update. I was hoping they could take out some of the bass response that seems to be prevalent on my Code 50 in the next firmware update. Does anybodt know of any plans to do any updates?
Hi everybody, no question but just a statement (just to show how satisfied I am with this amp, but also maybe to encourage other users): I LOVE THE CODE50!
I own two Code50's, one for rehearsels and one for gigs - so one is the clone of the other. Today I had a feeling I should "finetune" some of my already established presets due to a new guitar I recently bought. And what can I say? Everything worked as expected: The amp (sw-version 1.44) connected with the phone (iPhone XR, iOS 14.4, Gateway version 1.5), I was able to change presets via footswitch or phone, downloaded presets and edited them - as always absolutely no problems or issues.
Thanks to Marshall for an absolutely satisfying and reliable, easy to transport and always great sounding product! 'nuff said!
I just bought a Marshall code and found the apps on iOS do not work. Research says that the problem is the app need s to be updated. When are you going to update the IOS apps ?
I know this forum has this question asked a number of times, and the reply is always to delete the app and re-install. I've done this multiple times, and it never solves the problem. In fact, I had this app successfully installed on my iPad a few years ago, and hadn't used it latey. When I use it now, I get the same message.
Context3d not available! Possible reasons: wrong renderMode or missing device support
I googled this message and found out that it's related to Flash. Apple has discontinued all support of Flash on iOS devices. So my educated guess is that you need to re-vamp this application to not use any Flash programming. No ammount of deleting and reinstalling the app will ever solve this problem. You need to update the app.
I would like marshall to give us a program for the official PC in the style of Code Editor, since it has abandoned its development and support several years ago, so it has many bugs, so it would be a very good detail with all CODE users who Marshall made his own software for Windows 10 PCs and MacOS with which it was easier to manage patches, rename them, organize them, import them, export them etc. I hope they give us that.
I have a new DSL20CR. When I use emulated out, the signal is only present when the amp is on standby. When I switch the amp to low or high mode, there is no longer any signal on the emulated out. Is that correct?
The sound that a headphone, connected with the code100, produces does not include the effects that are placed in sent and return. That is really strange.
Music played with a phone or tablet that is connected with Bluetooth does go through the effects in the sent and return loop. Really strange again in my opinion.
I would like to know why it is wired this way and I would be really happy with a solution for at least the headphones!
Hi all, i’m looking to buy a new marshall sc20c jcm800 tube amp and get payday loans 24/7 and it doesn’t have a headphone jack . Could i plug headphones into the jack called “DI OUT” or not and what does this do?
owned a code 25 for a while now but only really started using it during lockdown but have to say I'm really impressed. I'm just using it for living room playing and connected to my DAW as a way of laying down ideas but seriously, it's REALLY good.
For context, I've played guitar for 27 years and working in live music has been my primary source of income (pre lockdown....) for around 17 years. I'm usually a live-sound engineer and tour manager and occasionally fill in the gaps with some guitar-teching. I'm uk-based but have international clients, mostly guitar-based, playing mostly academy sized venues but have done major festivals worldwide and one short stint of an arena tour. The point here is not to blow my whistle, simply to say I've spent a lot of time being exposed to all manner of amps and modelling.
I own a line 6 helix and while the CODE isn't as flexible with regards to I/O, I genuinely feel like it's amp-modelling, especially for crunch, fuzzy or blown out tones, blows the Helix out of the water. Not that I'm as likely to use metal tones or had much cause to tweak them but I've noticed those kind of presets can sound a little thin. Also, higher gain sounds in general could benefit from a graphic EQ somewhere in the modelling chain, as it can be prone to squeak at frequencies usually outside of a regular amps range, presumably because of the full-range nature of the cab.
So, my query is, is there any chance that the CODE range is likely to get any substantial firmware updates or maybe 2nd generation hardware that could bring additional functionality/Pro level durability and a decent footswitch... I'm impressed that you've managed to get that much functionality out of a mono-jack but a few extra switches or even just midi connectivity for use with after market footswitched to access would open the amp right up.
Personally, I'd love to see one capable of more complex I/O routing i.e. the ability to record your dry input to DAW over usb and similarly, route from the DAW to the amp input for re-amping.
Midi I/O and an xlr input with phantom and a decent sounding pre would make it a nice little hub for a solo recording setup.
Anyway, great work Marshall/Softube, really hope you develop the line further.
I am a recent ower of a Marshall Origin 20, which I got in July. I've really enjoyed the amp until I plugged in last night and got out absolutely no sound out of it. I couldn't figure out why, as nothing as happened to it and it worked fine two days ago. I took it apart to do some trouble shooting and found that when I have all the knobs max'd and output on 20 watts, I can hear a whisper of my guitar signal (nicely saturated, presumably by the preamp tubes) through the speaker. This sound is affected by all of the knobs. However, if I plug my guitar directly into the return of the effects loop, and activate the effects loop I get no sound whatsoever; no guitar, no hum, nothing. Because of this, I'm sure my speaker is not the problem. These things led me to think it was a power amp section issue, so I went down and purchased a new set of matched EL34's, threw them in there, and nothing changed. I'd really like to know if there's anything I can do to fix this, because this amp is not even a year old and I should not be having these kinds of problems with completely normal bedroom use.
Hi all. I have a Code 25 which sounds great through headphones using the cab emulation. Without headphones I'm struggling to find a cab that doesn't sound really boxy. If I switch the cab off, it becomes a fuzzy mess and is unusable. Am I missing something or is that just how it is?
Thanks in advance!
how to upload a preset from MyGateway to the Amp ?
... not to the Gateway library because this will then not be possible to control via footswitch.
there are also patches under marshallcode.tools from where a direct upload to the Amp is possible via USB.
however, not ideal if this would have to be done twice separately (?)
the library overview in MyGateway is ideal but I can´t find a way how to move presets from MyGateway onto the Amp.
Many thanks in advance for your help
-> meanwhile figured it out: drag & drop to Gateway Library, then in the App under the individual Preset, select both Amp + Library, press save.
I have a Marshall Code 50 running MCU version 1.44 and Gateway (Android version 1.5.5) on a Samsung Galaxy S9+ running the latest OS. I can bluetooth pair to the amp and play music, but can not connect to the amp to change my presets from the library. I have reloaded the latest firmware on the amp, deleted and reinstalled the Gateway app, paired and unpaired several times. Nothing seems to work. I even grabbed my old Galaxy S7 Edge phone and that Gateway app on it does the same thing. Does my amp need to be serviced for Bluetooth connectivity?
I just unpacked my two brand new Stanmore 2 (Voice) speakers.
I am using an IPhone XS max on IOS 13.6
I successfully connected them to Google Home and can use this app to play music.
I successfully connected them as generic Bluetooth devices and can use them individually for Bluetooth audio.
BUT I cannot get Marshall's own IPS apps to recognise them!
Marshall "Bluetooth" doesn't recognise their existence when they are switched as Bluetooth input, neither does Marshall "Multi Room" when they are switched as WiFi input.
So Marshall's own apps are a FAIL
Apparently I need the app to be able to "Couple" them as a stereo pair, which was the reason I purchased two speakers!
Anyone else having a similar problem?
I did notice on the Apple app store a comment from a downloader who had experienced the exact same problem, so clearly this is a known issue for Marshall.
I have reported this to Marshall support but I have no experience of them so I don't know how responsive they are?
i experiance a lot of crackle at some presets whitch is extremly anoiying !
it seems to disapear when poweramps turned off
i read alot of CODE users experiance the same and if its a software bug can we expect a software update soon?
Where can I find a manual for the DSL40CR amp? It looks like everything here is for the CODE amps. The print on the "manual" (a single sheet) that came with the amp is so small it's unreadable even with a magnifying glass.
I ask to the Marshall team the following questions :
Why is the sound of music through Bluetooth so bad ?
Whay can't we use command of the code 50 to correct : Bass, Middle, Treeble ?
It is really a pity that the difference of quality is huge between the soung of guitare and music !!
I've got an apple music subscription, and my alexa app has been linked to it. Apple music works fine with echo devices, but just not on this speaker.