I have a DSL100H, and would like to replace the footswitch with one that has LED's so I can tell what setting I am on with my back to the amp. Can I use a standard externally powered 2 button switch with a TRS cable?
Hello,
I obtained a Marshall Haze 40c and was wondering if there were any current-production amp footswitches that mimicked the 4-button footswitch for the amp that is now discontinued? I have seen some on reverb, but they are a bit pricey when shipping is added to the mix.
Also, im a bit tech-savvy and wouldnt mind making my own. I understand what it takes to make a 2-button channel control, but unsure how to wire a 4-button switch. Any schems out there ?
I just found out that my local dealer (baxshop in the Netherlands) updated the expected delivery time for the Marshall Code pedl-91009 from 3 weeks to 26 weeks... That's one of an update! Are there problems any with the manufacturing or deliveries that we have to wait that long?
Any info would be helpfull. I need the switch before gigging with the amp.
Greetings,
Freddy
Dear All. When recently reviewing the release notes on Code Firmware Release V1.1 it is indicated that it includes "2-way footswitch support". Can you please provide a list of what "2-way" footswitches are available for the Code 50 as well as what parameters each of the usable footswitches are able to control/change. Thank you!
Hi, the reverb switch on my TSL602 footswitch unit does not work. With the footswitch unit connected, I cannot therefore switch on any reverb in any of the channels unless I remove the footswitch from the back of the amp (which allows the reverb to work) - but then I have no way of changing channles other than pressing the manual switches on the front of the amp. Where can I purchase a replacement switch to see if thats the problem? Thanks.
Hi i need a footswitch to my vintage modern 2466 amp. Where can i buy one? or the functionality off it so i can build my own.
Tnx for makin asskickin amps:)
Jonas Bonnier
Just last month I received the PEDL91009 and I just started to really use it this past couple of weeks. I really like the feature and functionality of the footswitch, I am very glad I bought it.
I noticed that if I have the footswitch hooked to the amp and I accidently hit the edit knob on the amp, the amp locks up? I can't change anything on the amp via the amp's switches or via the footswitch, I have to power down and then power up the amp to get it to work again.
Anyone else have this issue?
HOW CAN I DOWNLOAD THE FULL USER MANUAL FOR THE AMP AND FOOTSWITCH?
I just got a Marshall TSL 60 head and am having trouble with the footswitch.
Of the five buttons: Clean - Crunch - Lead - Reverb* - FX Loop*
The Reverb and FX Loop are both latching switches and work fine. The Clean, Crunch and Lead switches are all momentary and there's some sort of digital logic switching going on on the board. The problem is with these switches.
When I turn the amp on, the Clean switch LED comes on. When I hit the crunch or lead switch, nothing happens (No LED, no change from clean).
I thought it was an issue with the switches, so I replaced them. Now Crunch and Lead still do nothing, but when I hold down the Clean it switches to Overdrive for as long as I am holding the switch. When I let go, it goes back to clean.
Anyone have any thoughts why the switches aren't doing their job? Could it be a fried transistor that's supposed to be controlling the logic switching that's going on (Anyone know a good way to test this?). Some more info on the footswitch...
[Schematic](http://music-electronics-forum.com/attachments/34024d1432077935-tsl-20footswitch_page_2.jpg)
[DIN Pin Guide](http://i81.photobucket.com/albums/j202/paperboy38375/Forum Pics/tsl100switchinginfo.gif)
[Board Pic](http://i91.photobucket.com/albums/k288/fixr1984/DSCF0946.jpg)
[Another Board Pic](http://i281.photobucket.com/albums/kk224/chrisdrane/TSLInternal_zps056b5334.jpeg)
I don't know quite how to use this. It's probably so simple a chimp could figure it out - that must be it. I'm so scattered that I've gone below chimpanzee on the ??? scale. Please help if anyone has or knows how to acquire this manual . Thanks in advance - seriously. D.L.
My JVM 410C doesnt have any volume coming from the channels.
One switch works green yelow, not red. Works fine with switch two. Switch three works green and yellow, not red.
switch four doesn't work at all.
No sound out of these channels without footswitch. Same results. Now, making a poping noise when turned off. I just got htis amp in June. Played a few weeks and then boom, nothing.
I tried using the FX Loop in back. That's when this whole thing started. As I correctly plugged in as instructions say, it immediately didn't make sound in these channels. Unplugged, guitar going straight in, same stuff. No volume through these channels.
The tubes are red, all glowing.
I need help. Thanks.
Hi I thinking about purchasing a footswitch for a MG100 Marshall head I have a G100R Head will these work together?
My amp is amazing but i want to hnow if. It's possible to put a footswitch for the knob clean/ crunch
Hello!
Have a 6100LM three channel head. The footswitch that comes with the amp is huge - it takes up a large amount of space of my pedal board and I only really use it 3-4 times during a set (swapping from crunch to clean and back, never really use the lead channel). Does anyone know of a smaller replacement footswitch that could do the job? I only really need "channel up/down". I know the head has midi switching but this kind of thing is not my strong point......
Appreciate any help I can get!
Best
Andy
what model number footswitch goes with the avt150h (head unit)?
Hello, is there a downloadable manual avaiable for the MG100 HDFX? Also, what footswitches are compatible with it?
Thank you.
I am running a Lexicon MX200 thru the serial loop on my JVM 205C. Sounds great but when I turn off the loop using the front panel selector button via footswitch or manually its still on and making whatever effect I have chosen. What have I not done correctly?
Bob
I'm looking for a Marshall Cabinet for my newly aquired 3203 - It origianlly paired with a 4x10 but am wondering how it will sound with a 2X12 and also - will just any footswitch do? I think the answer on that last one is yes but I am not sure.