I'm looking for a Marshall Cabinet for my newly aquired 3203 - It origianlly paired with a 4x10 but am wondering how it will sound with a 2X12 and also - will just any footswitch do? I think the answer on that last one is yes but I am not sure.

hello, i tried to use the update, but the PC gives an error (windows 7)

Hi, to change the power valves of my JVM 410, do I need a matched quartet or I can use two matched pairs? The bias is set by two separate trimmers, one for every pair, so maybe two matched pairs will be enough?

Thanks!

I wrote in a question you can please excuse me as now that I have the amp in hand, I am very happy. This is excellent.

I would consider how to add a high frequency speaker so music streaming is a bit brighter, but I notice the sound via USB is pretty good and one up on the Mustang series which did not stream music out the USB port. Thank You. I kept my G-Dec 3 Thirty around for that reason (plus tweeter and line outs - I might add). As I get used to this I might find the headphone out sufficient but wish you had added Lineout so the speaker stayed engaged but could take the lineout to other amps or recordering devices.

Can you tell us which interal speaker is used, ohm rating and the frequency response?

I do not want to open it up to figure it out since I plan on maintaing my warranty, at least for the next year.. :)

Thanks,

James

PS who signed off on this design, give them a raise :). But if you had a version with the features I mentioned, I would gladly have paid the additional cost and only been fully satisfied. Like I am at 96.75% now. You can quote me.

Is there an update for the factory firmware yet?

Thanks

Mark

I purchased a G50R CD from a friend. Is there a manual or any downloadable info on this amp? I would like to know more about the CD input on the back and how it's used. I really don't know much about it so any info is helpful.

Thanks....

Is my bluesbreaker a series ll model? The serial number is 1999-48-0866-AG

Hello, I purchased the DSL40C and MX212 Cabinet. I know the Speaker in the combo is 16-ohms. I also know the speakers in the MX212 are wired for 8-ohms. I know if I use the cabinet, I can't use the speaker in the combo together. My question is, has anybody ever put an 8-ohm speaker in the combo? I am thinking that two 8-ohm loads would give me a 3x12 config for extra beef! Would this work, and would the amp still sound just as good if I used it alone (to take to jam sessions) on the 8-ohm output? Thanks   

Hi why was the code amp released when it is imposssible to get a 91009 foot swich anywhere also no covers avalible to protect said amp. I am being told up to october on the swich and who knows on the covers. can you help.

whereis the serial number located on my MG100HCFX amp?

Is there a printable Code owner's manual?

Could you give me a rough age of My JTM45 Lead - Serial appears to be S5002

Cheers

Mike

Hello, I know this has been covered here and I have read all of the messages, but I would like some newer feedback regarding my newly purchased DSL40C implimented with a Line 6 POD 2.0.

I realize you can't shut off amp modeling and that to achieve the least amount of colorization, and preserve my Marshall tone as much as possible, I should set the POD 2.0 to Tube Preamp, and EQs to 12 o-clock, which shuts off Cabinet Simulation.   I want to use the POD 2.0 because it has a bunch of presets I use, which I will modify and it gives me multi effects with a Pedal. 

How should I route this, given the effects send on the DSL40C is probably line level, and has no attenuator. The POD 2.0 has instrument in and I presume Instrument out. I know it will run -10 and +4 when using TRS. I will say I don't see any documentation on the DSL40C loop. 

This is my first Marshall setup and need advice from you gurus.

Any and all advice is appreciated.

Thanks so much!

I updated the gateway app 5 minutes ago to latest version - my phone is an moto g (gen2) running android 5.0.2. The app worked sort of ok on previous version but now its giving a message as follows.

      "Screen not supported - tThe minimum screen size is 640x960" 

From what I can see under the message though looks to me ok I can see "00 EL34 Heaven" and all the initial presets not covered by the message but thats it nothing works so I guess thats it after about 2 and a half weeks of being apple to control from the app I now find that I cannot do anything from the app.

Any ideas what I need to do next.

hi site does noy reconize my model #MG15HCFX ? HOW COME?

Michael 

Is the speaker in the Code 25 a full range speaker and if not, will there be clipping issues streaming music into the amp while playing my guitar?

Thanks

Hi,

Can I check with you do I need to register my new Marshall headphone mode EQ? If so how do I do it?

Regards,

Chin How

Hello, I've noticed that the firmware update is only available for windows not mac. Is there any alternative way mac users can update? Or will this be an option in the future? 

Many thanks

The Amp model 2555x doesn't exist... Or I put wrong product code for this amp (begin with 255...) ? 

Thank you ! 

Best regards, 

Max

Hello. I have a marshall mkii lead head that I've had since I was young. The serial number is 9941L and I was trying to find a new power transformer for it. Can you help? Thank you.