I have a hard time to adjust sound levels between clean and super crunch each time I go from clean to super crunch and back the super crunch level is loud and my clean is low...could u please show how to equalize them together thank you!!!

My 2016 Code 50 has a non functioning power supply, i am in Australia and so far both E-mailing the local parts supplier and Marshal support has fallen on deaf ears , I am seeing all over here that there is no replacement for this power supply , if this is so , I can't believe that marshal would release such a shoddy product , it actually is quite a nice little amp , my jcm 800 and 1959 SL have been running since the 70's and eighties rock solid , I guess my question is can someone steer me in the right direction, because I don't want to have a brick in my studio 

i m searching for presets for the darkness, ca you help ? ty

when I bought the amp, some of the pots were scratchy as hell. I cleaned them all with contact cleaner and replaced the od channel gain pot. When I use any sort of gain, or even an od pedal through the clean channel, there is a slight crackling noise in the ‘background’. Lets say I strum a chord using gain, as the notes are dying out I can hear, what can only be describes as a crackle, almost like a crackle on a radio station that isn’t quite tuned in.. The less gain I use, the worse it is.

any help appreciated!

Is there a direct connection from the Code 100 amp to a Scarlett audio interface?  

Hello there!!

I recently bought a used Code 50. It needs to be reset I believe. I can't get the tuner turn on. I can't adjust any settings.  It plays, but sounds a little muddy at times. Would really like to be able to adjust the different mods and amps and what not. Thank you. 

Hi,

I've gotten used to the sound of my MG 15 CDR and I'd like to have a preset to replicate it. Does anyon have one or know how I can achieve that?

Thanks, 

CODE25のチューナーの使い方教えて下さい。

Got my first Marshall yesterday, but it doesnt really work. When I turn it on I sometimes have some sound (sometimes good sometimes bad) for like 10 sec-5 min.

But after that nothing. Turning it on/off doesnt help either. I noticed that it sometimes stops right when my phone connects/disconnects to the amp. Lights and everything is still on tho. What can I do?

My Valvestate VS65R only puts out about 5% of its original wattage. It gave a pop noise a while back while I was playing  at 70% volume and fell silent while I was testing a new capacitor. I found a set of circuit boards and transformer, installed them with a new tube but only get the small amount of sound even with everything turned up. I tested it with different combinations, transformers, boards, tubes, speakers, guitars, cables, but no luck. Any help on what the cause could be, or how to troubleshoot would be greatly appreciated. Peace and Rock On!

Hi I recently purchased a code 50 and try to update cable is connected and says ready for update but is still showing that the cable is not connected on the site 

Hi all, I'm chasing schematics for JMP-1 and 9005.

Thanks in advance. 

Cheers. 

Greetings,

How can I fix this issue while importing patches from my amp to the desktop?

Im connected, and I can change all the settings, but I can't grab the current patches.

I think I have fixed it in the past, but it has been a long time since I have used this software with my amp.

Hi

I am thinking about buying this amp.

Is the effects loop engaged by deafult. i.e no F/S connected

Can Effects Loop be switched  on/off by a Line 6 HX Effects (as well as using HX for channel switching).

Does Effects Loop   "tone suck" much?

Any experience/advice greatly appreciated

Thanks

I got a Marshall mg15fx couple weeks ago but my store button doesnt work. I dont know why. Can you help me?

Good morning

I own a 2555 jubilee and was a bit confused with its serial number 09171

Was it made in 1991? I thought they made them in the 80's

Your help would be appreciated 

Chris

Toda vez que vou trocar de um pré-set para outro gera um atraso enorme.

O  tempo de troca é muito longo deixando muito a desejar para usa-lo somente os pré-set 

do amplificador. A última atualização para corrigir possíveis erros foi em 2017. 

Como posso corrigir esse tipo de atraso?

lookin' for this to mod the amp, and maybe get some better tones out of it. I actually like this amp, regardless all the crap people throw at em'