Hi guys! I’m new with the CODE 50 and unfortunately I saved one music style over the 38' acoustic preset. Is it possible to recover the original preset? Do you know how I can solve this? Please help me.

Please people, could you help us to developing a new firmware update to fix the DSP AMP simulations for Code 25/ Code 50?

If you could make a fast research on web, you are going to see that this is a very common issue for all Code users. Probably the last firmware updates is affecting just a part of the DSP boards, not all, but in my case and many other people, we can not use the AMP simulations anymore, and the Distortion and Overdrive FX are not ok too.

At least,  could you make the older firmware versions available for tests? I'm sure that most part of the users prefer to have the original and very nice tones than bluetooth running better, better connection with the App, or any other improvement.

Thank you, and please, consider our beg.

Hi, I had a marshall code, dsl 1w, 15w and 40w. I liked of 1w, much loud! I sold all and I have been used a app amplitube with iphone and ipad + irig nano amp, but I figure out in the worst way about update versions, It just stops working after the update. A nice day, and you cant play anymore on analogic gear. 

Now Id like a all in gear and the better for me now its the Code 25.  Even without the app I can handle the amp manually. Although, be convenient. 

Whats the current version suportted for code today? My IPAD 9th  is 16.5, IPHONE 7 is 13.  Is it works? 

thanks. 

I have the possibility of buying an used MARSHALL CODE PEDL-91009 FOOTSWITCH for my MARSAHLL CODE 25, and the seller has told me that it does not come with the connection cable to the amplifier, is that really the case? What kind of cable do I have to use to connect the pedal to the mono or stereo jack amplifier?

This pedal has to be powered by a battery or receives electrical power from the connection cable with the amplifier?

Hey Guys

I'm looking for a good home amp that isn't a tube amp that I have to crank loud for my tone. Looking at either one of the amps from the MG series or a Code 50

I'm a blues, blues rock and classic rock player - Allman Brothers, Ten Years After, Savoy Brown, Doobie Brothers, Dire Straits, etc

New to Marshall amps - sure I've listened to a lot of the greats playing thru them but I'm not all that familiar with the various models.

With the Marshall MG series, I see various designations such has MG50CFX, MG50DFX, MG50GFX and the most recent are referred to as the Gold series

I worked in electronics so I would guess that the various designators are revisions that took place in the amps - does anyone have info on what those differences are? Or time lines, approx dates when the CFX, DFX and GFX amps were brought to the market? Any thoughts if one series are seen as better

Or would an older AVT50 be a better choice?

Any thoughts would be welcome and many thanks in advance

Keith

aka GnLguy

So, I have had this problem on my CODE 50.

I turn it on, plugged my guitar in it, everything normally, but after some seconds or minutes playing, it just get muted on! 

The funny thing is that the Bluetooth keeps working on... I tried to eliminate some bad connection but I never found one. My cable is good, my guitar is good too... I don't know, it maybe could be a board problem or a electrical/power supply fault... 

The Amp and display are up to the date, firmware 1.47.

Please any advice is welcomed 

I'm looking for settings on my Code 50 to get the tone that Mark Knopfler has on. "Our Shanghai-La" (live).

Tom F.

Hi there ,
I recently bought a DSL1CR and see that the one speaker output states 1x16 ohms. 
I am aware it can be run without a speaker for silent listening through the emulated output. 
Can I connect my 8 ohm 1923 external 2 -12 cabinet to the DSL1's 16 ohm speaker output and run it safely? 
Thanks,
Russ

bonjour

je recherche une preconfiguration de Mission Impossible Theme de Lalo Schiffrin

pouvez vous m'aider?

I've been holding off for the next-gen Kilburn for the last 2 years, but I'm obviously getting impatient since the last Kilburn was launched some 5 years ago and there's not even a speck of news out there about the next-gen! :((

Now that Middleton has come out, I'm guessing that it is the replacement for Kilburn.  Shall i go ahead with a Sonos, or is there still any hope for Kilburn III?

The Gain and Mid knobs on my Code 25 are unable to reach 0 or 10 despite being turned all the way down and up; the gain's range is 3.7-8.1 and the mids are 1.9-6.1. Resets and reinstalling firmware have yielded no results.

Have enjoyed code 25 for a few years.  Suddenly the amp has started to drop output.  Happens after a few minutes of playing.  All lights on, no noisy pots or anything.  Just no output.  I can switch it off and back on and output restores.  But after a short time, same thing.  No output, suddenly cuts out.  Nothing.  Anyone seen this?

After selecting a Preset, and after playing a song when I go back to the Gateway app I see a message saying, "Amp Disconnected, Connection with your CODE amp has been lost. Please check your amp and try to connect again." When I select "OK" it reconnects then I can select a preset. This seems like a new"bug" since the Gateway app has been updated to the current version. My iPhone is on a stand close to my CODE 50 the entire time. (about 1 or 2 feet at most).

Please advise. Thanks!

iPhone 13 Pro, iOS 16.4.1

Firmware: 01 Sep 2022 - v1.47

CODE 50

i have a question is this a legit one that I bought.??

Dear Marshall....

I'm a total fan and player of the Marshall Code Amp. In my opinion the best amp in the world ( The Marshall Code) that is...

This amp has everything I need to gig.. record..  and just jam... in one easy to carry unit..  But... I have a problem... my USB plug on my Marshall Code 100w Head is broken will not plug into my cord because the USB port was damaged by me. The prongs in the head were bent backwards and are broken...

IS THERE ANY WAY I CAN GET THIS AWESOME AMP FIXED... PLEASE 🙏 

THANKS.. Allen Perez 

allenperez911@yahoo.com 

Hello,

I'm going to replace the power tubes with a new kit of 4 matched EL34 and I would like to know what is the BIAS setting recomended by Marshal in terms of how much mV we should adjust on the reading of the Test Pins  CON5. I found someware that is 90mV per side, but also other different info (some guy said 76mV after consultation with a techician). Please could uoy kindly advice?

thanks!

I have  Marshall Code 100 and it is ususable because the presets keep changing by themselves. Is anyone else facing this issue? 

Why i couldn't can connect my Headphones with my Phone on Bluetooth??

I have the Major IV Headphone andta Phone from Xiaomi M4Pro

Bonjour,

Comment faire pour supprimer un preset de l'appli Marshall Gateway( code25).

Merci

My chassis says PWB980801A and after being told to junk this amp I saw an article that said burnt components definately harm other parts.  The burned parts on my circuit board are 1.) ZD3, 2.)another ZD3, 3.)R111&270J DAEDO, 4.)R112&330J DAEDO, 5.)a blue resistor with 2 black and 2 red rings on it, 6.)desoldered TR10, TR15, TR6 & TR9.  When I lived at 522 Rhea Street in Long Beach, CA  someone I was living with asked me to take my guitar and amp outside and play.  I did but a policeman said he would have me arrested is I didn't go back inside.  I would like to keep this amp but it is kind of loud for the one room where I live.  All the repairmen I've found have refused to fix it.  I told ASCAP about VanHalen and got $5,000.00 and bought this amp in 1984.