Why does my phone keep asking for a paring pin ever five to ten minutes to connect to my Marshall code 25 and keep disconnecting from my phone i have a Google Pixel 7a 

I´ve never palyed with an Amp Stand. I´ve got a CODE 100c and I would like to know if anyone has the esperience and if it is true that it feels diferent.

Hi,

I recently purchased a new Marshall ST20c combo amp. I absolutely love the amp. However, I purchased a Keeley reverb pedal (new) and decided to try it through the FX loop of the amp. I got no sound at all. Then I tried it through the front end of the amp and it works perfectly. Would I need to get this fixed under warranty or is there something I'm not doing correctly. I plugged the send from the amp to the input of the pedal and the return of the amp to the pedal's output. Please advise A.S.A.P. 
regards

Stephen Hubbard

I've got a CODE4X12 cab and want it raised from the floor but I'm struggling to find a stand that will keep it level (i.e. parallel to the ground). Anyone have any ideas?

Cheers.

The above amp loses power after 5 to 10 minutes of play and I get reverb even with the control in the off position. This is with the volume and master at half and on clean. In overdrive it does the same though I ocassionally get chorus or a sort of hammered repeat, It has been checked by engineers at Marshall who found no fault in any mode although I have heard from a reliable source that there have been these sort of problems before and the suggestion was to do with the switches. As i had to send this back via the dealer more than 200 miles away and back to marshall, I wouldn`t want to do it again with the same result even though it`s under warrasnty.

My Marshall CODE 50 presets button is not working anymore, anyone can  tell me  what  part I need to buy to fix it ? 

I think that this forum should be dedicated, if not to Marshall Code exclusively, then to Marshall products and not to anything else such as advertisements that have nothing to do with music or our concerns and hobbies.

Greetings

My Marshall CODE 50 is getting power and display is on, but not making any sound. I have tried disconnecting and reconnecting guitar cables and used two separate guitars, both same result. Hooked the guitar up to another amp to make sure it was not the guitar and the instrument worked. Issue seems to be with the CODE 50 itself. What steps do I need to take to trouble shoot? 

Benjamin Robb

When trying to preform first time firmware update in browser it says "CODE: Not connected", although cable is connected.

Context:

I have a Marshall DSL100 head and a MX212 cabinet. According to the Marshall website, the MX212 is an 8 Ohm cab and it has 2 Celestion Seventy 80 speakers (80W, 16 Ohm each).

Based on this, I supposed that the cabinet should be wired in parallel (16 Ohm / 2 speakers = 8 Ohm cab), like in the following diagram:

Currently, I have the speaker cable plugged from the 1x8 Ohm output to the input of the cab. It works perfectly and I haven't had any problem after almost 2 years of use.

The issue started when I decided to check the inside of the cab. I noticed that the speakers are wired like this:

From what I understand, this may also be another type of parallel wiring (If that exists). I would like to know if this is normal or something is wrong.

Thanks.

Hello, I can't find a preset for playing Immortal band, can you succeed to create such a preset ? Let me know. Thank You !

some time ago the jack imput of my amplifier burned so i was searching for a replacement but i didnt find one so i was wondering how i can get this piece 

Hello,

I got my DSL40CR brand new in November.  I love how it sounds, but it has an annoying and random issue.  Whenever I've been playing my amp for an extended period, about 30 minutes or so, it starts to hiss and buzz.  It starts quietly at first, but in the next few seconds, it gets louder and louder until it's ear-shatteringly loud.  The only way to fix it is by shutting it off and waiting a few minutes, and then the cycle will repeat in an indeterminate amount of time.  Turning it on standby mode does not fix it; shutting it off then immediately back on also maintains the noise.  The only way is to wait a few minutes.  This problem solely depends on how long the amp is on, as playing or not playing the instrument for the full period will result in the same problem.

What is the issue?  And how could I get it fixed/fix it myself?

Is the USB cable supposed to be included with the CODE 25 amp?  Mine didn't come with one.

My stockwell 2 could not pair or connect to any bluethooth nor can be found i reset it and tried all manuals info but still without result any help please?

I just bought my new Marshall Monitor II yesterday and the anc function suddenly goes wrong. It sounds like wind flows in right ear. What is wrong with it? Or is it the problem of the exsistence of app?

Hi, I just want to pass on that I just created a 60s Garage Rock fuzz sound like is heard on songs from the Nuggets box set etc.  Just in case anybody is interested.   Just look up "Garage Rock Fuzz".

Hello,

recently bought a DSL40CR-U a truly fine amplifier brialliant Marshall!

what does the "U" mean in a DSL40CR-U?   thanks Rod

Just got a MG30FX. It has a built in tuner, but nothing in the manual on how it works. Anybody able to steer me in the right place to figure out how to use this built in tuner? Pretty frustrating. Thanks

hola banda quiero saber cual es el programa de marshall con el que s epuede editar presets, a demaas de como ocuparlo como interface ,tengo el marshall code 50