How to best use external pedal (Blaskstar HT Metal distortion pedal) with Code 50 amp? 

Hello from Ukraine, Marshall team!

Can you add in the next update, if it will, fuzz the pedal or create a preset with fuzz sound.
Thank you and apologize for my English.

Using the the Fx Loop with my Boss GT-100 via the four cable method, can I put the Overdrive, Comp, Wah, etc., effects before the Code 100 preamp and the Delay, Reverb, Chorus, etc., effects after the preamp and before the power amp and the cabinet? In affirmative case, these functions (preamp, power amp and cabinet) remain available?

Hello!  I have a Marshall DSL40c, which I absolutely love.  I swapped the speaker out for a Celestion Vintage 30 (16 ohm) a little over a year ago, and it sounds great.  However, I recently got a lower wattage tube amp (Vox AC4TV) and have been running it through the DSL40c (basically using the DSL as a speaker cab, with the power chord disconnected). 

So here's the problem:  After 2 days of using this configuration, the DSL has started making a sound when I play the vox through its speaker.  The best way I can describe the sound is that it is like a tabmourine, like those little metal disks jingling together.  It does this on certain notes, like the open low E string, or a C chord, but not on other notes like a B chord (i.e. 1 fret away).

When I run the the Vox alone through its internal speaker - no issues at all.  When I run the DSL amp section alone through it's vintage 30, no tambourine sounds, although it seems that the green clean channel is lower volume than it used to be (the other 3 channels seem to me the same volume as normal).  There is also some instability in the volume (goes in and out, but in a sublte way).  There is some clicking and popping when I first fire it up, but this stops after it has been on for a while so not sure if this is normal or not.

I have been looking up reasons why amps may rattle, but everything I am finding describes issues with the tubes that are being played through - my issue seems to be a bit different, since the rattling (tambourine jingle) sound I am hearing seems to be coming from the Marshall when I am not using its tubes (playing through the Vox as a head).

Is it possible that a tube has gone bad in the Marshall, and when I play the Vox through the Marshall's speaker, the vibration is rattling the broken tube and making this tambourine sound?  Would a reduction in the volume of the green clean channel imply it is a preamp tube vs power amp tube (since the other channels are unaffected?)

Thanks for any help you can offer.  I don't mind taking it in to a tech, but I have read a lot of posts of people who took their amps to techs and had tubes changed, etc. and the problem persisted.  I want to have a pretty good idea of the problem before I start investing in having it fixed.

Thanks!

Hello!

I just bought a Code 100 head and a cabinet.  I want to use the head in a smaller room to learn more about it, using headphones or a MG15CFR,. Can I plug in the head to the input?  As the cabinet is rather heavy its really hard to move it to another place than my "studio".

After the sparking and smoke, it fried some wire's inside and fried a circuit board!!! Should  I just start over with the new Code!!! I love my old head, but cost is a consideration! Thanks for your outlook !!!

I've been enjoying my Marshall Stanmore Bluetooth Speaker for 5 years and it has suddenly stopped working properly a few weeks ago. When turned on, the red power light is coming on but there is no sound coming out, either when pairing via the Bluetooth connection or the Input source using the audio cable. I can hear a very low buzz sound which stay at the same volume level (even when turning the volume up). The speaker connects to Bluetooth but I can't get no sound out of it. Have tried with my Mackbook Pro and iPhone. I also have a Marshall Acton speaker which works perfectly. Any idea what's wrong with the Stanmore? Thanks.

Greetings from Vienna!

I have this amp since 4 years and the problem is, that the volume control knob is way too sensitive in the low level. Even if I turn it a 1/2 mm up the volume jumps from too weak too much too loud.

As I am using this amp in the studio for rehearsing and use a mic , it is allways a problem of volume. The others go directly into the PA not using the loudspeaker. As I cannot play mine at low volume it is too loud and disturbing the others.

Please advice

best regards

Gerhard

     I picked up a Code 50 last week so far I love it and the possibilities it offers.  Only issue I have had is when the Bluetooth is connected to my phone (Samsung Galaxy S7 Edge) if I get the phone too close to the amp I get a weird digital rattling sound coming from the amp.  I have not tried to see if same issue happens with my Android tablet though.  Has anyone one else had this problem or know the cause?

Where please Marshall Gateway for Android 4.2.2 ???

Latest version is for Android 4.4 and later and in Internet i find old version Marshall Gateway 1.2.6 only  - this version crashed after start :-(

Thang You

I am having problems getting connected through bluetooth. I phone 6s , was working yesterday then phone was turned off and now it will not find amp. I reset settings and no change. Please help.

Anthony

yo, can anyone recommend a mac demarco sounding preset? all his dreamy stuff

Can anyone suggest a preset or make one for the incredible Robin Trower tone.
Bridge of Sighs or Daydream

Hi,

When I connect Phone via bluetooth, I can not see a presets, only "tab to sync" when I tab  it is shows this one and one or two more, but the rest is still tab to sync. Next connecting and all presets list is tab to sync again. Code do not want to synchronized with gateway. Do you have any idea how to change that? 

Great amp but it looks unfinished.

Why is there not a gold strip of pufling under the Marshall logo. It is noticable by it's absents.

I can play my new DSL40 on the 20w setting on the clean 1st channel for 30-50 mins and the sound will shut off (does the samething on 40w setting). Crunch on 1st channel will be muted and the second channel no problem with sound at all. I've taken it back to the store and of course can't get it to reproduce the problem. I've checked my power connection, no reverse polarity, neutral and ground all fine. I do have 126 volts at the outlet. My power company checked the line coming to the house and had 126v on each leg and no problems with the ground and neutral. The shop that I purchased the amp is running 123v. I cannot find anything on this site to tell me the voltage tolerances of the DSL40. Is this problem an over voltage issue or something else?

I have a Code 100 and my instructor has Code 25 amps.  I neeed a consise explaination of how to copy a preset from a Code 25 to my Code 100.  So far, the tutorials and FAQs have been more confusing than helpful.  I have the Marshall Android app and can connect to the Codes but have not method of copying setup from one to another.

Can anyone steer me in the right direction?

Thanks!

The problem is that when I put the distortion pre fx my amplifier does not give the sound even with any preset, the other effects work correctly only the distortion does not, however when I connect my headphones I get the distortion sound but without the headphones it sounds

how can i get the tone for cuts like a knife

Hi I just bought a code 50 and when i try to plug USB cable with my computer (mac pro), evrytime i saw that so it is impossibe to change preset.